Round Snap Ring Swivel Jack w/ Footplate - Bolt On - Black - Topwind - 10-1/2" Travel - 2K
(307 reviews)
Price: $53.35
Round Snap Ring Swivel Jack w/ Footplate - Bolt On - Black - Topwind - 10-1/2" Travel - 2K
Retail:$57.57
Our Price: $53.35
You Save: 7%
Customers prefer these similar products
- All Info
- Reviews (307)
- Q & A (0)
- Photos
etrailer Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- 1001 - 2000 lbs
- Swivel Jack
- Topwind Jack
- Bolt-On
- Leveling Jacks
- Tongue Jacks
- 10 Inch Lift
- With Rectangle Foot
- Steel
- etrailer
Rust-resistant jack has a retracted height of 11" and an extended height of 21-1/2". The deep-seated retaining ring provides extra side-load support, and the spring-loaded pull pin lets you swivel the jack up for travel and down for use.
Features:
- Utility jack lets you raise and lower your trailer
- Ideal for agricultural and commercial applications
- Retaining-ring swivel design lets you swing jack up for storage, down for use
- Deep-seated ring ensures extra side-load support
- Convenient 1/2", spring-loaded pull pin secures and releases jack
- Topwind handle has claw grip for comfortable, easy cranking
- Easily folds away for storage
- Corrosion-resistant finishes
- Outer tube has durable black powder coat
- Inner tube and footplate have rust-resistant clear zinc finish
- Welded-on footplate minimizes sinking in soft ground
- Effortless greasing with built-in grease zerk
- Bolt-on mounting bracket included
Specs:
- Application: trailer frames with a height from 2" to 4"
- No more than 3" wide
- Bracket height
- Retracted: 11"
- Extended: 21-1/2"
- Travel: 10-1/2"
- Outer tube diameter: 2-1/4"
- Inner tube diameter: 2"
- Footplate dimensions: 7-1/2" long x 3-3/4" wide
- Handle radius: 7-3/4"
- Lift capacity: 2,000 lbs
- 1-Year warranty
TJBB-2001-B Ram Round, Pipe Mount Swivel Jack - Bolt On - Black - Top Wind - 10-1/2" Travel - 2,000 lbs
Compare to Bulldog BD151443
Item # TJBB-2001-B
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Did not fit
Customer Reviews
Round Snap Ring Swivel Jack w/ Footplate - Bolt On - Black - Topwind - 10-1/2" Travel - 2K - TJBB-2001-B
Average Customer Rating: 4.9 out of 5 stars (307 Customer Reviews)
Rust-resistant jack has a retracted height of 11" and an extended height of 21-1/2". The deep-seated retaining ring provides extra side-load support, and the spring-loaded pull pin lets you swivel the jack up for travel and down for use.by: Mark J03/09/2024
Perfect. Needed a jack for my off road utility trailer which is only 2” square. Just what the doctor ordered. Super fast shipping. Awesome customer service. Thanks.
by: Jrzoffroad03/16/2024
A great fold up and bolt on trailer jack stand.
by: Michael11/06/2023
This was the best addition to my little utility trailer. Keeps the tongue elevated and out of the rain and snow and makes everything easier in hooking and unhooking the trailer. Works great, mounted easily. Only issue was with me. Once I forgot to flip it up and rode off but that was my fault. Still works great. By the way I caught that within thirty feet so no damage.
by: Jason 02/24/2024
Just what I was looking for! Have it mounted - fits trailer nice and rated for what I need. Haven't put it to work yet.
by: James11/09/2017
A nice heavy duty jack that will serve me well. Great packaging and customer service is excellent. I plan on using this jack on my trailer that is made from an old model camper frame with an old model jack and large tongue frame. This trailer is used for hauling my side by side on hunting trips and for hauling my riding lawn mower. A+++++++
by: Angela07/22/2020
We bought this jack for a very small MC pop up trailer. Fits as described. Shipping was fast and the quality is impressive. Very sturdy. Still building so we have not tried it under more than 350lb. load. So far so good.
by: Schuyler09/09/2023
Good product, however NO printed instructions on how to install it. The diections covered how to weld it to the trailer chasis. This is a non-welded installation.
by: Peter 02/21/2024
Still working great!
by: Dennis 02/06/2024
This is really a heavy duty piece of eq uipment.
by: Daniel10/12/2023
It's perfect for my needs. I will be back for future purchases. Swift response on purchase.
by: Karen 08/04/2023
Jack as advertised. Instructions were for weld on only, but assembly was simple.
by: John 02/22/2023
Jack was more heavy duty than I expected, which is great. Delivery was quicker than expected. The Jack I purchased is a bolt-on, but the instructions that came with the jack were for a weld-on. However, installation was very straightforward.
So far, I am very pleased.
by: Todd 05/06/2023
It was exactly what I needed for my tra iler.
by: Lon B09/07/2020
I got this for a 5x8 utility trailer, for my uses it's perfect. It is much more solid and stable than cheaper versions. I also prefer the foot plate, it provides a more stable stand for working on the trailer if it's not attached to a vehicle. It saves the trouble of finding a block when storing the trailer, and it's always at the right height to hitch up when I need it.
by: Matt S08/30/2020
I’m so glad I purchased this jack for my trailer. It arrived quickly and when I got it I immediately installed it. It was very easy to install with just two brackets and four bolts and nuts. Done in five minutes. It is a very solid design and I like how the leg folds up with ease! I can now put my tailgate down without worrying about dinging it up! Should’ve bought this jack when I first got my truck! Thanks e trailer!!!
by: Michael 06/16/2023
Delivered as scheduled and promised.... Item fits the dimensions as indicated on the website and should work perfectly after installed.
by: George04/18/2019
Trailer jacks work like a charm. very easy to crank. bought 4 jacks to mount to boat trailer. The 4 jacks lift 3500lbs with no problem. I would recommend these
by: Wm06/01/2023
Exactly what I ordered as the description said!!
by: Dennis02/16/2019
Very good trailer jack, It was easy to install and holds the trailer tongue up nicely for hook up and un hooking. Thank you Etrailer for a fine product!
by: Richard 06/26/2021
For my application this replacement trailer jack was a huge up grade, especialy with the grease zerk ability to lube and protect from the elements.
by: Josh03/19/2018
I searched all over a jack like this that bolted up. Most places only had the weld on type. This jack is year old and still working great. I also like that it rotates up instead of pointing down like my old jack that was installed from factory.
by: Billy04/06/2018
I received this trailer jack (TJBB-2001-B) in a timely manner and it was exactly as described on your website. The person I talked with was very helpful when assisting me with the order. Installation looks very easy and I like the fact that it has a grease fitting for lubrication. I hope to get many years of service from this product.
by: Benedict07/23/2018
This trailer jack is a lot better quality than the one it replaced. Good price, good quality, I like the grease zerk makes it easy to keep lubricated.
by: Doug07/31/2018
This product is a value for what it does. I needed a short lift for a small trailer and this met my needs. I have not mounted it to the trailer yet however I did see if all was going to fit and it did. The hardware is included so it should be an easy install. Thanks eTrailer for all the good equipment to chose from.
by: Kirb06/19/2019
Put this Jack on my utility trailer and use it regularly. A real plus when the trailer is loaded and means I don't have to unload it immediately to drop the trailer. Easy install and plenty strong.
25
302
Show More Reviews
See what our Experts say about this etrailer Trailer Jack
- Recommended Replacement Tongue Jack For Additional Ground Clearance On Angle Iron Trailer FrameFor the etrailer Round, Snap-Ring Swivel Jack #TJBB-2001-B to fit properly on your homemade camping trailer the frame will need to be boxed. This would require having additional frame material welded where you intend to mount the new jack. I recommend installing the Ultimate Trailer Jack # 322-RDJ-2K in your A-frame mount. This jack assembly can be raised to 1-3/4" with the jack retracted and moved to its lowest setting. The jack can then be adjusted in 2" increments up to 12" and raised...
view full answer... - Recommended Replacement Trailer Jack for 1996 Viking Pop-Up CamperI don't have any trailer jack information specific to a 1996 Viking Pop-Up Camper but I was able to find some rough photos online and it looks like the etrailer Round, Snap-Ring Swivel Jack part # TJBB-2001-B with a welded on footplate. This might look a bit different than what you have now but should still work nonetheless.
view full answer... - Availability of Bolt-On Pipe Mount Trailer Jack with 10" LiftAll of our pipe mount trailer jacks do require welding, but we do have bolt-on jacks like the etrailer # TJBB-2001-B that should work. I was able to see that Kendon motorcycle trailers tend to have smaller frames and this jack is compatible with 2" - 4" tall frames that are no wider than 3". If your trailer frame is smaller than that please let me know and I can see if we have any other options available.
view full answer... - 2000 lb A-frame Jack that Cranks Faster than Lippert A-Frame JackThe etrailer Jack part # TJBB-2001-B has a 2,000 lb capacity and it would crank faster than what you currently have, but it is not an A-frame jack. I went out into our warehouse to determine how many cranks it would take to lift 1 inch and found that it takes 8 revolutions of the crank for the jack to raise 1 inch. Not all jacks have the same cranks per inch. Typically, the more cranks per inch the jack have, the more mechanical advantage it has over the lifting. But the length of the...
view full answer... - Trailer Frame Size, Footplate Compatible with a 2K Bulldog Snap-Ring Swivel Trailer JackThe etrailer Round, Snap-Ring Swivel Jack, # TJBB-2001-B, will fit on trailer frames up to 3 inches by 4 inches, so it should fit your 3 inch frame. It includes a footplate that is permanently welded to the jack.
view full answer... - How to Pick Out New Trailer JackThe best way to pick out a jack is to pick out one that has enough capacity to handle the tongue weight of your trailer. Typically, tongue weight is 10-15 percent of the total weight of the trailer. So, let's say your trailer weighs a total of 10,000 lbs. Most likely you would have a tongue weight of 1,000-1,500 lbs. Typically you don't have to measure first to pick out a trailer as the ability to crank the jack up and down give enough flexibility to allow for the standard trailer heights...
view full answer... - Is the Inner Tube Stationary on the etrailer Snap-Ring Swivel JackThe inner tube of the etrailer Round, Snap-Ring Swivel Jack item # TJBB-2001-B does not rotate when the jack is being cranked. It does stay static. The jack is grooved in the rear to keep the inner tube from rotating. I have attached a picture to show this.
view full answer...
- Can The Wheel be Replaced With a Foot On The Round Swivel Marine Jack # MJ-1500B? As the wheel mounts are welded on the Round Swivel Marine Jack # MJ-1500B you would have to cut them off and weld on a plate for this jack. We do have the Round Snap Ring Swivel Jack # TJBB-2001-B which also fits trailers with a 2" to 4" tall frame but comes with a 7-1/2" x 3-3/4" footplate rather than a wheel.
view full answer... - Length of Fulton Jack # FXP15L In Stored PositionThe Fulton Bolt-Thru Swivel Marine Jack - Bolt On - Sidewind - 12" Lift - 1,500 lbs # FXP15L has a complete length when stowed sideways of 27-1/4 inches from the top of the jack to the bottom of the wheel. Your tongue length is incredibly short so you most likely won't be able to use a jack with a wheel as the wheel itself is either 6 or 8 inches diameter on jacks. I recommend part # TJBB-2001-B which will be just over the 14 inches of space you mentioned when in that stored position....
view full answer...
- Trailer Jack Compatibility with 14 Inch Tongue SpaceThe Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson # DL22800 has an overall length of 26-5/8 inches, so it will not fit where you are desiring. The height to the bracket when retracted is 13 inches, but the overall will to too long. The closest I found was the # PS1400300303 which is 11 inches to the center of the bracket when retracted as is # TJBB-2001-B.
view full answer...
- Recommended Marine Trailer Jack w/ a WheelI do have a jack for you but the etrailer Item # TJBB-2001-B you were looking at does not have the option to add a wheel. Instead you will want the Pro Series Snap-Ring Swivel Marine Jack item # PSEJ10000101. This jack is similar to the Fulton F141005014 you referenced that is no longer active. It is a side wind jack, with a wheel, that has a 1,000 lbs capacity. It has a small foot print for the mounting bracket. I have linked a diagram below that will show the dimensions.
view full answer...
- What Mounting Bracket Is Needed for the Round Snap Ring Swivel Jack TJB-2001-ZThere is only one bracket needed to install the Round Snap Ring Swivel Jack part # TJB-2001-Z on your utility trailer and the bracket is included with the jack so no additional purchases are necessary. I have pointed this bracket out for you. It will need to be welded to the trailer frame. If you don't want to do any welding on the trailer then you can use the Round Snap Ring Swivel Jack w/ Footplate part # TJBB-2001-B instead which is essentially just a bolt-on version of the above jack...
view full answer...
- Availability of Swivel Jack and Trailer Tailgate Lift AssistThere are bolt-on swivel jacks you could change to that would offer similar specs to your current one. The Round Snap Ring Swivel Jack # TJBB-2001-B has a 2,000 lb lift capacity, extended height of 21-1/2" and retracted height of 11". It is for trailer frames that are between 2" and 4" high and no more than 3" wide. I've added a link to each of our bolt-on swivel jacks for you to take a look at. As for a lift assist, I recommend the Gorilla-Lift Utility Trailer Tailgate Lift Assist # GL1....
view full answer...
- Swivel Jack with Sturdy Pull Pin To Eliminate Jack Movement While Winding and UnwindingI'll start off by saying that part of the play that you're experiencing has a bit to do with the bolt on feature vs. a welded on jack; bolted on jacks are going to have a bit more play on them, but there are some features in jacks that you can look for that will lessen the play/wiggle you're experiencing. First, choosing a top wind jack over a side wind jack will help reduce some of the movement when you're winding/unwinding. Second, a strong pull pin that locks the jack into position...
view full answer... - A-Frame Trailer Jack that Can Attach to Inside of Trailer FrameSo the Trailer Valet 5X Swivel Jack # STC-V211 uses brackets to mount to the side of a trailer frame. For a trailer jack that uses the same style of topwind handle and mounting brackets we have the Round Snap Ring Swivel Jack w/ Footplate # TJBB-2001-B which would work well.
view full answer... - Is There a Blank Cover Plate Which Can Mount Over Holes For A-Frame Trailer Jack Holes? I have never seen a blank cover plate to cover the hole on your trailer A-frame, but you should be able to easily fabricate one out of a steel or aluminum sheet. As an alternative to the Snap Ring Swivel Jack # TJBB-2001-B you could also consider the Ultimate Trailer Jack # 322-RDJ-2K. This jack mounts in the same space as your current A-frame jack and will allow you to lower it to one of 7-different heights to clear your tailgate.
view full answer... - Bolt-On Swivel Jack For Improved Ground ClearanceYou are correct that welding steel to aluminum is a tricky process best left to experienced welders, but if your issue is that you jack sometimes scrapes on the ground you can avoid the need to weld by simply bolting on a swivel jack. Pull Pin Swivel Jack # TJBB-2001-B has a 2000-lb rating, includes a foot plate and bolts on to the side of trailer frames up to 3-inches wide and from 2 to 4 inches tall. Just pull the pin to swivel the jack up and out of your way for travel. This jack extends...
view full answer...
- Trailer Jack to Avoid Tailgate Clearance IssuesThere are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like # D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the hitch on your vehicle is, the rise or drop of the ball mount for your trailer, if you're using weight distribution or not, and the measurement from the center of the hitch pin hole to the center of the ball hole I can make the best recommendation...
view full answer...
- Replacement Tongue Jack for 2002 Triton LT Snowmobile TrailerWe don't have any offset jacks like the one you have on your 2002 Triton Trailer. I recommend going with the etrailer Round, Snap-Ring Swivel Jack # TJBB-2001-B as this jack will be more convenient as you will not have to reach down as far. This jack includes a welded footplate.
view full answer... - Measurements of etrailer 2K Snap-Ring Swivel Trailer JackI went out to the warehouse and pulled an etrailer trailer jack # TJBB-2001-B. From the center of the mount to the bottom when retracted is approximately 11 inches.
view full answer...
- Does Trailer Jack # TJBB-2001-B Include Mounting HardwareThe topwind swivel jack, part # TJBB-2001-B, does include the hardware to mount to the trailer frame. The trailer frame needs to be within 2 to 4 inches tall and no more than 3 inches wide.
view full answer... - Can Trailer Jack # TJBB-2001-B Have the Gears and Shaft Removed?You can use the Round Snap Ring Swivel Jack w/ Footplate # TJBB-2001-B for just the outer tube and mount while removing all the inner parts. The capacity of the parts will not be rated any higher than the 2,000 lb rating of the jack because it has not been tested in that manner.
view full answer... - How to Pick Out a Trailer Jack for a Boat TrailerThe best way to pick out a jack is to pick out one that has enough capacity to handle the tongue weight of your trailer. Typically, tongue weight is 10-15 percent of the total weight of the trailer. So lets say your boat and trailer weight a total of 10,000 lbs. Most likely you would have a tongue weight of 1,000-1,500 lbs. Without knowing your tongue weight but knowing the weight of your boat I recommend you take a look at a 2,000 lb jack like the etrailer Round Snap Ring Swivel Jack...
view full answer... - Recommended Bolt-On Swivel Jack for 5K Food TrailerI recommend using the 2K Round Snap Ring Swivel Jack w/ Footplate # TJBB-2001-B OR the 1,500 lb Round Swivel Marine Jack # MJ-1500B if you'd like a jack with a wheel. Both of these are cost-effective options that are still quality products. The 2K jack has an extended height of 21-1/2" while the jack with a wheel has an extended height of 24". Every bumper pull trailer should have a tongue weight that is no less than 10% or no more than 15% of the weight of the trailer. Since your 5K trailer...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Jameson C
Expert Research:
Adam R
Video by:
Joshua S
Installed by:
Cole B
Installed by:
Brent H
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Mike S
Written by:
Amanda M
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.