Trailer Jack to Avoid Tailgate Clearance Issues
Question:
Checked clearance, not even 11 Jack would work. Not too keen on a longer shank ball mount would have to be over 8 longer?? Looks like frame mounts? Pivot type bolt on? Trailer weighs approximately 1200#. Would prefer casters, but a foot plate could work too. Trailer is a tandem 16 footer. Frames are 4"
asked by: Edward L
Expert Reply:
There are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like # D-26, that would move the trailer back further away from the truck and give you clearance you need.
If you know what size the hitch on your vehicle is, the rise or drop of the ball mount for your trailer, if you're using weight distribution or not, and the measurement from the center of the hitch pin hole to the center of the ball hole I can make the best recommendation based on your trailer.
Another solution is to use a side mounted trailer jack. This moves the jack back further and to the side and provides you the clearance for you tailgate. We carry jacks that have casters on the bottom like # FXPD15L and jacks that have foot plates on the bottom like # TJBB-2001-B.
I linked the pages with our extended ball mounts, and our selection of side mounted trailer jacks for you to check out.
Products Referenced in This Question
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Fulton Boat Trailer Jack w/ 2 Wheels - Sidewind - Swivel - 12" Lift - Zinc - 1.5K
- Trailer Jack
- Boat Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 12 Inch Lift
- Bolt-On
- With Wheel
- Fulton
more information >
etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 29-1/8" Lift - Zinc - 2.5K
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 2001 - 3000 lbs
- Sidewind Jack
- 29 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Round Snap Ring Swivel Jack w/ Footplate - Bolt On - Black - Topwind - 10-1/2" Travel - 2K
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Swivel Jack
- Topwind Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- 16 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: 7-Way Molded Trailer Wire Connector, 4' Long
- Shop: RV Interior Lighting
- Video: etrailer Single Axle Trailer Fender with Backing Plate Installation
- Shop: Fusion LED Hardwired Trailer Light - Stop, Tail, Turn, Backup - Oval - Red/Clear X Lens - 20 Diodes
- Shop: Gustafson 12V LED RV Dome Light - Single - 5-7/8" Long x 3-3/4" Wide - White
- Shop: Mini LED Trailer License Plate Light - 2 Diodes - Clear Lens - 12V/24V
- Shop: Roof Rack
- Search Results: license plate light
- Shop: Optronics LED Trailer License Plate Light with Bracket - 1 Diode - Clear Lens
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Solution for Tailgate That is Hitting A-Frame Jack
- Search Results: 54006~058
- Search Results: 7 way
- Search Results: 7 way extension
- Video: Review of Optronics Trailer Lights - Tail Lights - OPT59NR
- Video: Review of Optronics Trailer Lights - Tail Lights - OPT67NR
- Search Results: 7 pin trailer plug
- Search Results: flush mount backup light
- Search Results: back up lights
- Video: Hopkins 7-Way Molded Trailer Wire Connector Review
- Video: Optronics Trailer Lights - Tail Lights - STL78RB Review
- Video: Optronics Oval LED Trailer Light Review
- Video: Optronics Trailer Lights - License Plate Lights - LP31CB Review
- Shop: Fusion LED Hardwired Trailer Light - Stop, Tail, Turn, Backup, Warn - Oval - R/W/Y Lens - 20 Diodes
- Shop: Peterson Great White LED Trailer License Plate Light w/ Bracket - 1 Diode - Clear Lens
- Q&A: What Are The Replacement Adapter And Seat For Yakima CoreBar Crossbars Made Out Of
- Shop: Trailer Hitch
- Q&A: Which Is Easier to Crank, a Side Wind Jack or a Top Wind Jack
- Q&A: Difference in Side Wind Operated A-Frame Jack and Top Wind A-Frame Jack
Edward L.
1/1/0001
Checked clearance, not even 11 Jack would work. Not too keen on a longer shank ball mount would have to be over 8 longer?? Looks like frame mounts? Pivot type bolt on? Trailer weighs approximately 1200#. Would prefer casters, but a foot plate could work too. Trailer is a tandem 16 footer. Frames are 4"