Trailer Jack, Sidewind Swivel Jack with 6" Wheel - 1200 lbs. by Dutton-Lainson
(93 reviews)
Price: $87.34
In Stock
Trailer Jack, Sidewind Swivel Jack with 6" Wheel - 1200 lbs. by Dutton-Lainson
Item # DL22300
Our Price: $87.34
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (93)
- Q & A (0)
- Photos
Dutton-Lainson Trailer Jack - DL22300
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- Bolt-On
- Leveling Jacks
- Tongue Jacks
- 10 Inch Lift
- With Wheel
- Steel
- Dutton-Lainson
Trailer Jack, Sidewind Swivel Jack with 6" Wheel - 1200 lbs.
Features:
- Bolt on mounting
- Enclosed outer tube retards sand and dirt from contacting miter gears and heavy-duty Acme screw
- Fits channel tongues up to 3" wide x 5" tall
- All mounting hardware included
- 2.5" Diameter mounting hole in swivel bracket fits most other brands of mounting hardware
- Floating miter gears allow for proper clearance and easier operation
- Maximum maneuverability from offset swivel caster assembly
- Zinc plated TUFFPLATE finish for longer life
- Zinc plated yellow chromate TUFFPLATE finish has three times the corrosion resistance of standard zinc plated trivalent chrome process and 30 percent greater corrosion resistance when compared to powder coated finish. Results of lab test using 5 percent neutral salt spray confirms our TUFFPLATE finish provides in excess of 500 hours against First Red Rust and in excess of 100 hours of First White Corrosion.
- Ergonomic hand grip with textured surface
Specs:
- 10" Lift
- Measurement of mounting plate: 6-3/4" x 5-3/4"
- Capacity: 1200 lbs
- 1-Year limited warranty
When hitching and unhitching loaded trailers, D-L tongue jacks are real back savers. These easy-to-install smooth operating tongue jacks can be mounted in a variety of ways on various sizes of trailer tongues. Heavy-duty D-L tongue jacks reduce physical effort required to maneuver a loaded trailer into hitching position or removing the trailer from a vehicle. All models are made from heavy-gauge steel for strength and durability.
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
22300 Trailer Jack, Sidewind Swivel Jack with 6" Wheel - 1200 lbs. by Dutton-Lainson Model 3400
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
Customer Reviews
Trailer Jack, Sidewind Swivel Jack with 6" Wheel - 1200 lbs. by Dutton-Lainson - DL22300
Average Customer Rating: 4.7 out of 5 stars (93 Customer Reviews)
Trailer Jack, Sidewind Swivel Jack with 6" Wheel - 1200 lbs.by: Terry07/04/2019
This device is fairly heavy-duty, sturdy, and the swivel works easily and smoothly from horizontal to vertical and latches/unlatches easily. It adds flexibility to the trailer's built-in screw-up/down jack with a flat plate on its bottom. It allows me to move the trailer easier without having to lift up the front end. The customer service was great: a customer service rep got involved and expedited the order processing so it arrived a lot earlier that I expected from the website,. That's excellent customer service. Thanks!
by: Joyce B03/17/2015
I needed one for my woodsplitter which has a 2”x2” tongue, this works great. It was easy to install and it makes raising and lowering my woodsplitter a breeze. I would highly recommend this product . I use my 4-wheeler to move my splitter and this works perfectly, glad I found it. thanks so much
by: Joe09/30/2019
Problem was that regular Cargo trailer front Jack had to be removed every time I hooked it up behind Camper because of zero turning clearance to rear bumper.
Swing Jack installed closer inboard of hitch on Trailer frame and folded after hook up provides unlimited turning clearance. Added value was the ability to move trailer since Jack has large diameter wheel.
Special brackets allowed for easy installation. (no drilling/tapping of holes)
by: Stewart 05/01/2024
Delivery date as promised, good service.
by: Terry 10/09/2022
Greatjack, much better than I had
Terry
11/3/2023
Great jack. Has done well.
by: Chad 11/11/2022
This took a small modification to my trailer as I had angle rails and not solid rails. But this has held up great. Sturdy design, ease of use!
I am very pleased with this product.
by: Eric08/12/2021
I'm writing this review one year after purchasing. The original reason for buying was to allow room for a double hitch with a bike rack in it while towing a pop-up camper. It did the job well enough that I decided not to take it off & put the original back on. I don't trust it enough to turn the trailer on the wheel with the exception of perhaps on a smooth driveway and while not too-extended.
by: John L.06/21/2016
I use this product on a shorelander boat trailer hauling a 16.5 ft Lund Mr. Pike.
I have had no problems with this wheel jack. In fact it has performed admirably for me.
by: Shel10/07/2015
Pro: Seems well built. The swivel is much heavier duty than the original that came with the trailer. Well packed and all the mounting hardware was present. Con: No grease fitting for lube.
Shel
10/6/2016
It hasnt gotten a lot of use as its on a snowmobile trailer and we didnt have much snow. It has been outside all this time and no rust:
by: Tony 09/24/2023
Fast delivery
by: Steve L.08/08/2014
This was a replacement jack for the original which was accidently damaged and the new one works perfectly. I'm very happy with the jack, the ordering process and the overall experience with etrailer. I highly recommend this company.
Steve L.
8/8/2015
After ~ 1 year, the trailer jack still works perfectly. Very satisfied wthe product and the etrailer company.
by: Chuck Campbell03/22/2016
After 1 year I can say that my Trailer Jack, Side wind Swivel Jack with 6" wheel has made this old guys job moving, hitching and storing so much easier. It is installed on my 16 foot cargo trailer (Motorcycler Hauler). We have travelled all over the Eastern USA and Canada taking in the Calbot Trail Nova Scotia and the Florida Keys. There has only been the wife and I and both in our 60's and we have no problems now moving the trailer loaded or unloaded and it moves and stores easily. Great Product!
by: Rob08/13/2014
This swing-back marine jack is a great buy and the materials are nice quality. I used this to replace my original 800lb. Fulton jack that came with my Shorelandr' double PWC trailer (long overdue). Since this jack is rated at 1200 lbs., I had to drill a larger hole on the trailer frame and on the jack swivel bracket, plus I had to move the pin from the right side to the left side of the jack (left side is meant for smaller pin/right side for larger/picture online is incorrect). This is a nicer jack than the original, the pin is heftier and the extra work was worth it. Time will tell how long it lasts around salt water.
by: Richard08/17/2018
Trailer jack has functioning very good.
The only problem is the finish is starting to corrode for some reason. I am going to try to put a coating of wax on it to see if it helps.
The trailer jack is only used in the spring summer and fall and is stored inside and has never been out in the weather. The trailer jack is always inside in the winter.
The finish is not adequate and I am not sure why the corrosion is taking place.
by: Creeker204/23/2014
Looks well-made, install went well. Will reserve final judgement until after the season as to long-term reliability. Great initial follow-up service from e-trailer.com.
Creeker2
4/23/2015
Best one Ive had
by: MAK07/26/2017
Trailer tongue lift fit well, easy install, works great and I still using it.
Mak
7/26/2018
Still works fine
by: Joe05/11/2020
This is a great product. Sadly it was made in China. At one time they were made in the United States. Hopefully, someday they will return production to the USA.
Joe
5/12/2021
Working fine. Dont like it was made in China.
by: Brian 09/26/2022
Easy enough switch out. Bolts are much longer than the original on mine so I felt like I was ratcheting forever, but that's what makes it a mostly universal fit. Take a look at your original bolts and see if you would rather use those to make install a little faster.
by: Slob08/28/2015
I purchased two of these jacks to mount on my portable welders so they could be rolled around by hand in the shop. Both installed easily without reading the instructions and function flawlessly. Although manufactured in China, they are of good quality and will serve my purpose well. The welder in the photos weighs just over 1400 pounds and pushes/rolls very easily on the shop floor. etrailer.com and their usual outstanding service provided these at a good price shipped rapidly.
I will continue to use etrailer.com for my light trailer needs.
by: Bob08/20/2015
This an extremely well made trailer tongue jack at a reasonable price. I especially like the 6" wheel. My previous jack did not have a wheel and this wheel makes it much easier to move the trailer by hand when I need too.
by: Ray H04/03/2018
Ordered this boat jack...was missing one of the brackets in the parts bag...I called and received great customer service...they looked up the missing part and sent a replacement out to me asap. Jack works great so far and installed easily. Thanks
by: Gary S.10/22/2014
This is a GREAT company to do business with. I have been burned many times ordering things over the interweb; but this company has it all together. I received my trailer jack in record time. It is just what I needed. The quality is exceptional for the low price I paid. I will recomend this company to everyone I know.
Thanks etrailer, sort of restores a persons faith in humanity!
by: john w06/17/2014
as described, easy to install ( no installation instructions included but offers from eTrailer to help & instructions/video on website), works great, A++++++
by: MotoMac11/10/2014
Outstanding. This was ordered for my 6x12 enclosed dirt-bike hauler because a fold-up model gives much better ground clearance when going on rough dirt roads. It is well-designed and well-put-together. The installation was a breeze and it works perfectly. I strongly recommend this jack.
by: Bill M.02/21/2017
Very nice. Replaced 25 year old jack that had begun to grind. Easy install. Crank is very smooth. Quick shipping from etrailer. Thanks.
25
93
Show More Reviews
See what our Experts say about this Dutton-Lainson Trailer Jack
- Bolt-On Trailer Jack for Small Ironton Utility TrailerFor your trailer you might like a rack and gear jack such as # BD169201. This jack will bolt around trailer frames or tongues that are up to 3"x5". This type of jack has the ability to draw the wheel up very close to the mounting bracket which means the clearance from where it mounts to the bottom of the wheel is only 7-1/2 inches when the jack is fully retracted. I have linked a video review of this jack for you. It isn't a swivel jack but since it can retract so far it is an alternative...
view full answer... - Trailer Jack Recommendations for a 10,000 Pound A-Frame TrailerA trailer jack only lifts part of the weight of the trailer and not the whole 10,000 pounds of your trailer. A 10K trailer would have a tongue weight of around 1,000 to 1,500 pounds. But the higher the capacity of the jack the easier it is for the jack to lift the weight and the longer it will last. A jack rated for 5,000 pounds such as # TJA-5000S-B is an option. You could add foot # JF-99 as well. I have linked a video review of the jack for you. If you'd prefer an electric jack then...
view full answer... - Side Jack Mounting Hardware for a 2021 Bass Tracker 175 TXWThanks for the picture! I would be happy to help you. To mount your jack to your Bass Tracker 175 TWX trailer you will need the Mounting Hardware for Dutton-Lainson Bolt-On Trailer Jacks item # DL22443. This kit includes four 3/8"-16 bolts that measure 4 inches in length. I have linked a diagram I made of the back piece of the mounting bracket so you can confirm this will fit your boat trailer.
view full answer...
- Swivel Trailer Jack with Bracket Height Under 12 InchesRack and gear jacks like # BD169201 can get low with a bracket height when retracted of only 8 inches. But rack and gear jacks are low capacity, 750 pounds, and do not swivel. Another low option is Fulton fixed jack # TJ12220301 which can actually get lower than even a rack and gear jack. This jack measures a mere 9 inches from the center of the mounting bracket to the bottom of the wheel. But it does not swivel. The lowest I can get on a swivel jack with a wheel is 12-3/4 inches like...
view full answer... - What 3/8 Diameter Swivel Pin Replacement Do I Need?For a 3/8" diameter swivel pin replacement that is similar to # DL22454, I recommend the Replacement Swivel Handle Kit for Dutton-Lainson Jack # DL22449. However, this part is only designed to fit the Dutton-Lainson Jack # DL22300.
view full answer... - Replacement Trailer Jack for Dutton Lainson Jack of Ranger TrailerThe only trailer jack we can recommend that would fit on the same frame mount as your 2012 Ranger trailer that has a Dutton Lainson jack currently is another DL jack like with the part # DL24MR since all of the jack manufacturers use slightly different mounts. Typically the DL jacks work well so I would be inclined to believe that your jack had issues before you got it and the new # DL24MR would work well in place of it. If you did want to switch up the brand the Fulton part # FXP10 that...
view full answer... - Replacement Trailer Jack Wheels for a Bass Tracker Boat TrailerWe have lots of wheels for jacks, see link to the right. If you know the manufacturer and model/capacity of the jack that you have on your Bass Tracker boat trailer I can determine which is the proper wheel.
view full answer... - Trailer Jack Recommendation that Has Tires that are InflatedWe currently only have one jack that has tires that are filled with air and that's the Trailer Valet 5X part # STC-V211 which actually is designed to allow a trailer to be moved around by hand with it's crank handle. The jack you mentioned part # DL22300 that you referenced has plastic wheels. I attached an install video for the Trailer Valet for you to check out as well.
view full answer... - Recommended Swivel Jack With Wheel For Small Utility TrailerThe trailer jack I recommend for your utility trailer is part # DL22300. This is a sidewind swivel jack and it has a 1,200-lb weight capacity. This jack also comes with a 6-inch wheel, and has a 10-inch lift. This is a bolt-on installation and will fit trailers up to 3-inches wide and 5-inches tall.
view full answer... - Availability of a Bolt On Swivel Trailer Jack That Can Accept a Wheel or FootplateAll of the side mount jacks that we carry either come with a welded footplate or welded wheel. Though the tubing size is 2 inches, I cannot recommend modifying jack # DL22300, or any jack with a wheel or footplate welded on, as it will void the warranty and make the capacity unknown. If you could go with an a-frame mount, we have several options for jacks. You could go with something like the etrailer Round A-Frame Trailer Jack - Topwind - 14-1/8" Travel - 5,000 lbs # TJA-5000-B, and...
view full answer... - Distance From Mounting Bracket U-Bolt To Ground On Fulton Jack # F1413020134I pulled the Fulton F2 Swing-Up Trailer Jack, part # F1413020134, from our warehouse and took a photo and some measurements for you. This jack has dual 7 inch wheels and features a sidewind handle. The jack has an adjustable mount, and is a bolt-on installation, and does feature a swing-up option. This jack fits up to 3 inch by 4 inch tongues, and has a weight capacity of 1600 lbs. I moved the mount to the position that would be lowest on the jack leg and measured the distance from the...
view full answer...
- How to Mount the Bulldog Pipe Mount Swivel Sidewind Jack BD158109The Bulldog Pipe Mount Swivel Jack, item # BD158109, has a short pipe that will need to be welded to the trailer frame. The jack can then be rotated on the pipe to swing it up out of the way when towing. The jack can also be easily removed if needed. If you are looking for a bolt on jack we have several models available, see link. Your trailer frame height and width will help when selecting a bolt on jack. I would recommend the Sidewind Swivel Jack by Dutton-Lainson, item # DL22300, if...
view full answer... - Dutton-Lainson Trailer Jack # DL22300 Replacement Wheel # DL22440 RecommendationIt looks like you will need a Replacement 6 Inch Poly Wheel for Trailer Jacks, part # DL22440. This wheel is an exact replacement for your Trailer Jack, Sidewind Swivel Jack with 6 inch Wheel - 800 lbs. by Dutton-Lainson, part # DL22300.
view full answer... - Corrosion Resistant Trailer Jack for a Trailer with 2 Inch by 4 Inch FrameI think the best choice is going to be a bolt-on Dutton-Lainson jack with a Zinc plated yellow chromate TUFFPLATE finish. If your trailer has a channel tongue, jack # DL22300 fits up to a 3 x 5 inch frame. If you have a square tongue use # DL22800. The finish on these jacks is very corrosion resistant. An aluminum jack that will fit your frame size is not available.
view full answer... - Does Dutton Lainson Trailer Jack DL22300 Require any Ground ClearanceFrom the center of the mounting bracket down to the bottom of the wheel of the Dutton Lainson Jack part # DL22300 that you referenced measures 13 inches. You'd want to compare the height of your trailer coupler to the ground when it sits level to see how much clearance you'd have. The good thing about this jack though is that it is designed to swivel out of the way when not in use so it essentially does not require any ground clearance.
view full answer...
- Mounting Hole Size and Placement on Dutton-Lainson Sidewind Swivel Jack # DL22300I checked the Dutton-Lainson website but a complete engineering diagram of this item is not available, so I took a piece from inventory and measured the mounting hole spacing. All eight mounting holes on the Dutton-Lainson Sidewind Swivel Jack # DL22300 are the same diameter, 0.42 inches (or 10.6 millimeters). The attached photo indicates the measurements which are taken from hole-center to hole-center. This jack includes mounting hardware and offers a 1200-lb lift capacity. A review...
view full answer...
- Recommended Futon Swivel Jack on Sled Bed Trailer With 6 Inch Tall Frame MemberWe have a solution that will work for you, but none of the bolt-on trailer jacks we offer are compatible with a 6 inch tall trailer frame. For a trailer frame of that height, I'd recommend you use a weld-on jack like part # FTJ120W0301. This jack has a 1200 lb capacity, and easily swivels rearward for storage with the pull of a pin.
view full answer... - Can Jammed Fulton Trailer Jack Be Freed UpWhat you describe typically happens if the jack has been over-extended or retracted. I'd continue spraying PB Blaster on the screw, followed by some raps on the end of the screw with a mallet or dead-blow hammer which will hopefully free things up. If that fails, unfortunately your best bet would be to replace the jack. I'd recommend a US made jack from Dutton-Lainson, part # DL22300 which is a bolt on jack with a 1200 lb capacity. The outer jack tube is sealed to prevent dirt and debris...
view full answer... - Trailer Jack Recommendation for Trailer with 2 inch Tall Trailer FrameSounds like you are looking for a trailer jack for your trailer that has a 2 inch tall frame. On a trailer with frame dimensions as small as yours I would recommend a pipe mounted jack like the Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate # PS1401440303. This jack comes with a 2 inch outer diameter pipe that gets welded to the trailer frame that the jack installs onto. It can swivel out of the way when not in use too.
view full answer... - Replacement Cap for a Dutton-Lainson Model 3400 Boat Trailer JackIf you have Dutton-Lainson jack # DL22300, which is model 3400, then you can use replacement cap # DL22354. If you have a different model or brand then we may have a cap for it. I have included a link to the jack caps we carry.
view full answer... - Availability of 1000-lb-Rated Dutton Lainson A-Frame Tongue JackWe do carry trailer tongue jacks including products from Dutton Lainson. We offer the 1000-lb-rated side-wind tongue jack # DL22530 which comes without a wheel or foot and that can be installed either by welding or by bolting it to your trailer tongue. This jack provides 15-inches of lift height. All 1000-lb-rated a-frame tongue jacks are displayed on the linked page. I searched the Dutton Lainson website for your original part number and it no longer returns any results so it is likely...
view full answer... - Are There Any American Made Trailer Tongue Jacks Available?We do indeed carry American made jacks. You will want to check out the Dutton-Lainson line. All of their jacks are made here except the Model 7201 # DL22320 and Model 3400 # DL22300. With that said, if you are specifically looking for an A-Frame jack, you will want to check out the Dutton-Lainson A-Frame Trailer Jack - Topwind - 5,000 lbs. # DL22772. This will have 14" of lift , but does not include a foot plate. If you prefer a foot plate, you will want the # DL22542, but if you wanted...
view full answer... - Trailer Jack Recommendation with Short Distance from Mounting Bracket to Bottom of WheelFrom the center of the mounting bracket down to the bottom of the wheel of the Dutton Lainson Jack part # DL22300 that you referenced measures 13 inches. Another low option is Fulton fixed jack # TJ12220301. This jack measures a mere 9 inches from the center of the mounting bracket to the bottom of the wheel. But it does not swivel.
view full answer...
- Recommended Trailer Jack To Replace 1,000-lb Shelby JackWe do have a replacement trailer jack that will work for you but it is not a Shelby. I recommend the Dutton-Lainson Trailer Jack, part # DL22300. This is a bolt-on jack that will fit trailers up to 3-inches wide and 5-inches tall. This jack has a 1,200-lb capacity and features a 6-inch wheel.
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Jacob T
Updated by:
Adele M
Updated by:
Wilson B
Updated by:
Mike S
Video by:
Kathleen M
Installed by:
Randy B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Terry
7/5/2020
Great! It makes it so much easier to hookupunhook my trailer.