Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black
(326 reviews)
Price: $349.00
In Stock
Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black
Item # ORJW750BD
Our Price: $349.00
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (326)
- Q & A (0)
- Photos
- Used (1)
Ark Trailer Jack - ORJW750BD
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- Bolt-On
- Leveling Jacks
- Tongue Jacks
- 10 Inch Lift
- With Wheel
- Steel
- Ark
The dual wheels on this jack run through mud or over gravel and sharp rocks without getting stuck or damaged. Easy-to-grip handle lets you drop the entire jack tube down for quick adjustment with minimal cranking. Great for everyday and off-road use.
Features:
- Sturdy jack supports, lifts, and lowers your boat or recreational trailer
- Thick-walled, square tubing is precision machined to limit play between inner and outer tubes
- Dual steel wheels with off-road rubber tires provide increased traction and maneuverability
- Wheels lock into place when stowed to provide clearance and prevent damage during travel
- 4 Height settings allow for fast, easy positioning - no block or drop leg needed
- Drop jack to desired height with easy-to-grip handle
- Reduces cranking time and effort
- Spring-loaded pin with easy-to-grip handle lets you easily swing jack into place
- Pivot up to stow parallel to trailer tongue for travel
- Move back into upright position for use
- Sidewind hand crank easily removes for storage
- Attaches for use with sturdy internal magnet
- Bolt-on installation - hardware included
- Sturdy steel construction is durable and built to last
- Corrosion- and rust-resistant black powder coat finish has 600-hour salt spray rating
- Designed in Australia to stand up to the rigors of the Outback
Specs:
- Application: 3" to 6" tall x 2" wide trailer tongues
- Retracted bracket height: 12"
- Extended bracket height: 29-5/8"
- Maximum height when moving trailer: 23-1/2"
- Usable lift (screw travel): 10"
- Total travel (including pin adjustability): 17-11/16"
- Static load capacity: 1,650 lbs
- Dynamic load capacity: 1,100 lbs
- Wheel dimensions: 8" diameter x 2" wide
- 1-Year limited warranty
Designed in the Outback for all-terrain use, this rugged jack is equipped to handle just about anything, from moving your boat trailer to accompanying you on off-roading adventures. You'll appreciate the smooth operation and adjustability for everyday use just as much as you'll enjoy the special features designed for extreme use. From jobsites to campsites, the Ark Extreme trailer tongue jack will work for you.
Easily Move Your Trailer over Any Terrain
Dual steel wheels with rubber tires provide increased surface area for smooth, steady travel. The rubber tires can cruise over rocks without breaking or getting flat spots, and the tread helps prevent sliding in wet conditions. The overall strength and durability of these wheels also keep them from stalling in sand or light mud.
Sealed bearings act as bushings to hold the wheels in line on the cross shaft. This is an improvement over traditional plastic jack wheels, which often have just a bolt going through them, providing very little stability and causing the wheels to wobble, lock up, and drag over time.
The heavy-duty, durable design of this jack lets you take your trailer off-road, over rough terrain, and through various climates. The sturdy steel, square body provides increased side-load capacity and superior strength, and limits play between the tubes. And the corrosion- and rust-resistant zinc finish offers a 600-hour salt spray rating to withstand wet or rainy conditions. The built-in grease zerk lets you lubricate the internal screw when necessary for continued smooth operation over time.
Safe, Easy, Out-of-the-Way Positioning for Travel
A sturdy magnet is built into the jack's easy-to-grip crank handle for secure attachment of the jack crank. The handle detaches easily to store away and prevent hang-ups while traveling, yet it's strong enough to stay put while you're cranking the jack up and down.
The convenient, side-mounted swivel pin has an easy-to-grip handle, making it fast and simple to swing the jack down for use or up alongside your trailer tongue for travel.
The yoke latch at the bottom of the jack offers 5 positions to hold the wheels in place. This allows you to tailor the configuration of the stowed jack to suit your needs. So if you have anything mounted on your trailer tongue that the wheels might hit if they're positioned upright, you can lock them in place facing down instead. If you're off-roading and traveling through rough terrain where you might have issues with ground clearance, just lock them upright. This locking feature also keeps the wheels from swinging around while you drive, which will help to ensure that the bearings don't wear out prematurely.
Fast, Easy Setup with Minimal Cranking
Once you've arrived at your destination, setting up is a breeze thanks to the quick-release jack tube on the Ark Extreme jack. Just tug the spring-loaded handle to quickly drop the jack tube to your desired height. This handle allows you to set the jack in 1 of 4 positions. Once you have it as close to the ground as it will go, just rotate the crank handle on the front of the jack to fine-tune the height.
Having the ability to drop the jack tube in this manner means that you won't need a drop leg or space fillers like blocks or bricks. And far less cranking is needed to get the jack into position, which will you save you both time and effort.
When you're ready to pack up and hit the road again, hitch the trailer back up to your vehicle, retract the jack's inner tube using the crank, and reposition the jack back alongside your trailer tongue.
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
ORJW750BD Ark Extreme Off-Road Trailer Jack with Dual Wheels - Black Edition - Bolt On - Sidewind - 10" Usable Lift - 1,650 lbs
Alt XO750 Black Edition
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Arrived Damaged
Customer Reviews
Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black - ORJW750BD
Average Customer Rating: 4.6 out of 5 stars (324 Customer Reviews)
The dual wheels on this jack run through mud or over gravel and sharp rocks without getting stuck or damaged. Easy-to-grip handle lets you drop the entire jack tube down for quick adjustment with minimal cranking. Great for everyday and off-road use.by: Marc04/26/2022
I installed my Ark750 on my small off-road camper trailer about a year ago. I was needing a trailer jack that did more than just help me more my trailer around my garage and on easy flat terrain. Found myself is a situation where heavy truck sunk in some soft/wet soil. Disconnected my trailer, got my truck out and was able to winch out my trailer with my truck with the trailer jack down. There is no way my stock trailer jack could have handled this job!
by: Michael10/16/2022
I needed a rugged off road jack. Our factory jack didn't last one season on our 2021 Intech Flyer Chase. After fabbing up a new, heavier duty jack plate, the XO750 black edition complimented our overlanding trailer nicely!
by: Greg05/31/2023
The package came destroyed, missing the crank handle. I contacted etrailer for a replacement, got the run-around, sent them pictures, continued to get the run around, after a year, I am still using a crescent wrench to lift my trailer. I had to take it apart to re-drill a hole so things lined up better.
by: Brandon 05/19/2023
This is a very well designed trailer jack. I have a 21ft yamaha boat and a factory height 2015 gmc sierra. Using the OEM shorelander trailer jack required the use of a 4 inch block of wood to hitch the trailer. I needed extra height and a much heavier weight capacity over what came with my boat trailer originally. This jack solved both of those issues. I now have a few extra inches of height left in the jack when I hitch up. The extra lift also comes in handy when I want to get the bow up to drain the boat. The magnetic jack handle is genius. I also love how the spring loaded stowing handle folds out of the way and allows me to stow the jack in multiple positions. My tongue weight was 780lbs and the oem jack struggled big time and just wasn't safe with that load. This jack has no issue easily lifting that. I've since moved the boat back on the trailer and lightened the tongue weight to 480lbs to keep the truck suspension happy. If you have a newer yamaha boat with a factory shorelander trailer, do yourself a favor and get one of these trailer jacks. They are pricey but absolutely worth the money. Rest assured you are getting what you are paying for with this trailer jack.
by: Kevin04/12/2022
I purchased a “Stealth Hitch” and “Extreme Off Road Trailer Jack.” Both are awesome! The hitch is exactly what I was looking for because it doesn’t hinder the appearance of the rear bumper when not in use. The Jack is also perfect because it rolls easy and doesn’t mark up my paver driveway. Oh and looks awesome!!! GREAT JOB etrailer!!!
by: Nate08/29/2021
This off road Ark trailer jack is great! Very well built and looks great too. Just as important more to me as buying a product is customer service and etrailer is top notch. I had a small issue when mine arrived and Carol C was all over it as if I was her top priority fixing it promptly. I was starting to think that in the world we live in that there is no customer service left. Thank you Carol C. for giving me hope! I will continue buying all of my trailer needs from you! Quality, fast shipping and good coroner service. Can’t ask for more
by: Matt S.05/01/2024
Quality product! This will be the 2nd one I bought, the first stayed on the trailer I sold, when I bought my new trailer this was the first thing I ordered.
etrailer has always been awesome, fast shipping and great information.
by: Marcia 08/25/2023
This is our third trailer jack for a 2019 Sea Fox Commander 328 boat. The other two broke. We are not worried about this one breaking. Thank you!!!!
by: Bob Z07/26/2023
This trailer jack is very well built. It's solid with heavy duty parts. I have used it for a full year of service and it shows almost no wear.
by: Trailering happily in Boise !04/20/2023
First of all, this is a SOLID unit, extremely hefty. Have yet to actually put it through the paces, but initially, very impressed. FINALLY, a trailer jack that allows me to actually turn the trailer when maneuvering it by hand, unlike single wheel jacks that simply will not turn in the desired direction. Two wheels is the only way to go if you have to move a trailer by hand. As with most products these days, the instructions are incomplete. Right off the bat, you are faced with two wheels and 4 sets of bearings, none of which are assembled. The first item the instructions SHOULD say is before putting the wheel assembly together you have to install the bearings into the wheels, and there is zero mention of that. Fortunately etrailer took my call immediately and walked me through the process, and I'm glad I called. Instinctively I knew the bearings had to be inserted into the wheel hubs but they are tight. My first inclination was to grab a hammer and start pounding them in. That would have been a big mistake. The etrailer rep told me to use a rubber mallet, not a hammer. A hammer would have probably destroyed the bearings and maybe the wheels as well. Start the bearing install with them square to the hole and take your time, they will go in, but its a process. After that, everything is pretty straightforward. The bolt heads and the nylock nuts are different sizes, which may or may not be 'normal', but it makes no sense to me. Other than that, I think this jack is going to serve me very well for a long time!
by: David 03/09/2023
Easy install within 30 min. Very heavy duty. Pull pins to swivel and raise lower are a bit tight but shod get better with time. Solved my Cricket trailer issue with previous jack interfering with tailgate. Also like the handle is removable.
by: Doyle08/27/2021
Wheels wobble. One bearing fell out during assembley. The other bearing had to be pounded in with a hammer. Bolts are too short to mount on a 3 inch square hitch. I expected better for $xxx. Disapointed!!!
Sierra K.
9/7/2021
If you believe the bearings are defective on this product, it does have a 1-year warranty through the manufacturer. Unfortunately, this product is designed to fit 2 inch wide trailer tongues.
by: 10/06/2022
exactly what was described and i wanted
Kent
10/9/2023
Strong and sturdy for support. Wish it had rubber or nematic tire. I use mine as a wheel at the ramp for launching a boat so i am using for other than it was really created.
Mike L.
10/25/2023
@Kent A rubber pneumatic tire is kind of a double edged sword, they ride a little better, but they can puncture which would be a bad thing...
by: JW05/30/2023
Brilliant design. Non-existent instructions, written or online, on how to install it. I spent a solid day trying to figure out how to do it.
by: Corey08/01/2023
Product is fine but this item didn’t work for me and it will cost xx of the xxx I paid to return back. Make sure you get the correct item or better yet buy on [online] returns are easy and free and item was 9 dollars cheaper I really wanted to give my business to smaller companies but I can see why [online] wins.
by: Larry 11/17/2021
Love the adjustable height
Larry
11/18/2022
This jack is definitely strong and sturdy. I use it on a boat trailer and so far so signs of rust or corrosion. Definitely recommend over any stock jack.
by: Bradley 02/04/2023
Very solid build. Functions as described. Replaced existing trailer jack of lower quality.
by: John05/14/2021
I am rating this it’s a one star because of the poor customer support I received from etrailer. I emailed etrailer asking if the bolts provided would fit a 3 inch frame, they replied and said the bolts will fit from 3 to 6 inches Frame width. Boots provided are only 3 inches long, and I needed 4 1/2 inch bolts.
Heather A.
5/19/2021
Thank you for your review. The bolts provided with the Extreme Off-Road Swing-Up Trailer Jack w Dual Wheels part # ORJW750BD are 3.14 long so the trailer frame cannot be wider than 3 wide. It does fit frames 3 to 6 tall.
by: Jonathan02/03/2022
Great replacement for cheap standard jacks. Love how solid it is- especially with my off-road trailer. Moves in dirt relatively easily with two wheels. The fact I can take off the handle off is just one extra bit of security for piece of mind.
Would like to get the matching leveling jacks someday.
by: Burgess08/13/2019
Added this to my camper, and can't say enough good things about this jack! Manufacturer thought of everything! 1st: was easy to install and plenty of factory holes for adaptability. 2nd: This thing is beef cake. Burly construction. Could withstand winching your trailer. 3rd: Adjustability... you can actually use the 10" of crank, because the wheel has holes to adjust downward, before using the crank extension. 4th: stores up, out of the way, and can rotate the wheel and lock in multiple positions so it's not banging around, roughing up your trailer.
by: Rick01/24/2021
Awesome jack. Should have downsized to the smaller unit but wasn’t available in black.
by: Lee02/26/2022
This trailer jack is the bees knees. No more lifting the trailer and pulling it around. It is compact, heavy duty, and everything they say in the video. Great product, quick shipping.
I also bought the extended tongue and this awesome hitch. ETrailer is my credit cards new best friend.
by: Moab Trailer Time10/08/2020
Great upgrade for a Moab camping trailer. I broke the wheel on the standard jack but based on how much easier moving the trailer is now I don't expect any issues. Not shown is that the wheels are steel centers with ball bearings - much better than all plastic wheels on a sleeve. I will be ordering this again for my boat.
by: Alex 10/26/2022
donna was the absolute best; she was very kind and very thorough; im going to keep working with etrailer as long as i have someone like donna to work with.
25
325
Show More Reviews
See what our Experts say about this Ark Trailer Jack
- Swivel Jack With Wheel For 6 Inch Tall x 2 Inch Wide Trailer FrameWe have one option for a swivel jack with a wheel for a trailer with a 6 inch tall x 2 inch wide frame: - Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black # ORJW750BD or Zinc # ORJW750D While the # ORJW750BD is more for off-road applications, this is the only option for a jack that is going to fit the frame size of your trailer as they are generally for a maximum of 5 inch tall frames. This is a heavy-duty jack with steel wheels and rubber...
view full answer... - Dimensions Of Mounting Plate For Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BDHere is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack # ORJW750D in zinc which will have the same dimensions as the black Jack # ORJW750BD you are looking at.
view full answer...
- Replacement Handle For ARK Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BDWe have the Replacement Jack Handle # ORJW750SH which will fit your Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BD. This handle has a zinc finish as opposed to the black finish on your jack.
view full answer... - Installing Extreme Off-Road Swing-Up Trailer Jack On Trailer With 3" Wide TongueThe Extreme Off-Road Swing-Up Trailer Jack # ORJW750BD is listed as fitting 2" wide trailer tongues, but I reached out to Ark and you can still use it with your trailer. The jack uses M8 high tensile bolts so you will just need to find some that are the correct length at your local hardware store in order to install the jack.
view full answer... - Folded Jack Length of the Xtreme Off-Road Ratcheting Trailer JackWhen folded up and traveling the Xtreme Off-Road Ratcheting Trailer Jack item # ORJW750BD is 29" long from the top of the jack to the bottom of the wheels. From the bottom of the wheel to the center pivot point where the bracket attaches is 14". When folded up this hitch can still slide forward and backwards on the mounting bracket to accommodate limited space. The Extreme Off-Road Swing-Up Trailer Jack item # ORJW750BD will fit any trailer with a tongue ranging from 3" to 6" tall. The...
view full answer...
- Will the Ark Extreme Off-Road Swing-Up Trailer Jack ORJW750BD Fit on a 16 Foot Cargo Trailer?To make sure the Ark Extreme Off-Road Swing-Up Trailer Jack # ORJW750BD will fit your trailer, there will be two things that need to be confirmed. First will be the tongue weight of the trailer you want to attach it to. This has a static, or resting, load capacity of 1,650 pounds and a dynamic, or lifting, load capacity of 1,100 pounds, so you will want to make sure your trailer does not exceed these tongue weights. Next, the # ORJW750BD will fit on 3 inch to 6 inch tall trailer tongues...
view full answer...
- Can the ARK Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels be Welded On my Frame is OversizedWhile it is typically used as a bolt on jack the ARK Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels part # ORJW750BD can be used as a weld on jack. The bracket that is used to mount it is a standard steel. You will have to clean off the finish on it of course but touch it up afterwards and you'll be in good shape.
view full answer... - Specifications Of The Ark Extreme Off-Road Swing-Up Trailer JackThe Ark Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels # ORJW750BD you referenced weighs roughly 40lbs. The Ark # ORJW750BD has a 1650lb static weight capacity, and an 1100lb dynamic weight capacity. This jack will offer up to 10" lift and will work on trailer tongues between 3" - 6". This jack will be a great addition to your trailer allowing you to move your trailer around due to the two 8"x2" wheels, and a strong black powder coat finish to protect the jack from rust and corrosion...
view full answer... - Does Extreme Off-Road Swing-Up Trailer Jack Fit 2 x 6 C-Channel Trailer FrameIt sure does! If you take a look at the accompanying photo I added from an install we did, you can see the Ark Off-Road jack installed on a C-channel trailer frame. The correct part number for this jack is the following: - Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs # ORJW750BD The # ORJW750BD will fit trailer tongues up to 2" wide and between 3" and 6" tall. You asked about other jacks, but this would actually be the only option for a jack...
view full answer...
- What Is The Max Height Fully Extended On The Xtreme Off-Road Trailer Jack # ORJW750BDThe Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels # ORJW750BD has an extended bracket height of 29-5/8 inches. The maximum height when moving a trailer is 23-1/2 inches. It has a static load capacity of 1,650 pounds and has a dynamic load capacity of 1,100 pounds. This jack has a bolt-on installation with the hardware included and has a sturdy steel construction that is durable and built to last. It has a rust-resistant black powder coat that has a 600 hour salt spray rating. I...
view full answer... - Can ARK Extreme Off-Road Trailer Jack w/ Dual Wheels Fit 23" High Trailer FrameYes, the ARK Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW750BD can easily fit and work with a trailer frame that sits 23" off of the ground. In the attached photo the bottom of the trailer frame sits 19" above the ground and the jack not only has another 5" of travel (at least), the main body tube can be adjusted further down so there is more than enough clearance at a 23" height.
view full answer...
- Recommended Replacement Jack for a Shelby 5856A-24Z I recommend going with the Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheel # ORJW750BD to replace your Shelby 5856A-24Z. This jack is a bit heavier duty than your current jack with a max weight capacity of 1,650 lbs, has a simple bolt-on install, and has 4 different height settings for easy and quick adjustments.
view full answer... - Recommended Replacement Trailer Jack for a 20-Year Old Four Winns Boat TrailerI recommend going with the Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels # ORJW750BD. This jack is similar to what you have now, has a 1,650-lbs lift capacity, a 10" lift height, and is coated with 600 hours salt spary corrosion resistant coating making this ideal for marine use.
view full answer... - Extreme Off-Road Swing-Up Trailer Jack Shipping Weight The shipping weight of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black item # ORJW750BD is 44 lbs.
view full answer... - Recommended Bolt On Trailer Jack with Rectangle Foot For 1,200lb TrailerWe do have a potential option for your with the ARK Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BD. We do not offer any thing with a foot plate that will fit your parameters. So if you are willing to use a jack with a dual wheel, this will be a great option. The dual wheel is very stable, and can be used just like a foot plate for long term storage. The ARK jack is extremely well-made, it will ride sideways when you are driving, it has a hand crank, and it will fit frames up to 6" tall....
view full answer... - Smoother Trailer Jack For Moving Enclosed Trailer AroundI've had the same issue before and converting to a rubber wheel helped me a lot. It seems that the bearing inside your jack isn't doing the best job. Since your hauling a snow mobile I can presume that snow is on the ground which of course means salt.. The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels # ORJW750BD has a 600 hour salt spray rating which will help keep the salt from corroding the bearings keeping it moving smoothly in your garage over time. This is for sure a great...
view full answer... - Will Ark Extreme Off-Road Jack ORJW750BD Fit 2" x 2" Trailer Frame?I reached out to my contact at Ark and he was able to confirm that the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels # ORJW750BD you were looking at will work just fine on your seeder with a 2" x 2" frame. This jack offers up to 10" of lift, and has a 1650lb capacity with dual wheels with rubber tires to allow you to easily move your seeder around when it is unhooked from your tow vehicle. I included a video of the # ORJW750BD for you to take a look at.
view full answer... - How To Confirm Fit of the Extreme Off-Road Swing-Up Trailer JackThe Extreme Off-Road Swing-Up Trailer Jack part # ORJW750BD will fit any trailer with a tongue ranging from 3" to 6" tall. The width does not matter as longer bolts can always be used to accommodate different needs. That said, I don't have any sort of copy to provide you with but so long as you go by the above you will not be lead down the wrong path.
view full answer... - Can Bulldog Square Swivel Jack # BD190708 Be Fitted with a Caster Wheel AssemblyThe square-tube jack you referenced, the Bulldog Swivel Jack # BD190708, is a drop-leg type and this cannot be fitted with a caster assembly. However we do offer a range of jacks that have caster wheels, both A-frame and side-mount types, and these can be viewed by clicking on the link to your right. Do please note that any jack with a caster wheel will have a lower lift rating than the Bulldog. Wheels do not have the same weight capacity as a standard foot plate, so if a jack were available...
view full answer... - Xtreme Ark Off Road Trailer Jack that Can be Used on Trailer Frame with 19 inch Above GroundThe Ark jack you referenced would not go up high enough for the height of your trailer but we do have the similar Ark jack part # ORJW750BD that can go up several inches taller and would work for you.
view full answer... - Are Wheels of Extreme Off-Road Jack Available Separately for use on Other JacksThe wheels alone are not something that can be purchased separately from the Extreme Off-Road Swing-Up Trailer Jacks, so if you wanted the benefits of the jack's steel wheels and off-road rubber tires you would need to get the whole jack. There are a number of different sizes and weight capacities available for this jack, which are the following: - 7" Lift, 770 lb Capacity: Extreme Off-Road Swing-Up Trailer Jack with Dual Wheels - Zinc # ORJW350D - 10-3/4" Lift, 1,100 lb Capacity: Extreme...
view full answer... - Will the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303 Fit a 2" Wide by 3" Tall Frame? The Pro Series Round, Snap-Ring Swivel Jack # PS1400300303 will fit on your log splitter with the 2" wide by 3" tall frame. It has multiple mounting hole sets which allow it to fit a 3" to 4" tall frame. And the included bolts allow for a 2" to 3" wide frame. The only other recommendation I would make is possibly using a jack with a wheel like the # ORJW750BD if you often push the log splitter around. This will save you from having to lift the front of the trailer to push it around.
view full answer... - Bolt On Trailer Tongue Jack Capable Of Fitting a 6" Tall FrameFor a 6" tall frame I recommend the ARK Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BD as the Dutton-Lainson # DL22320 will only fit a trailer frame up to 5" tall. The ARK jack is rated for up to 1,650lbs capacity and fits trailer frames up to 6" tall and 2" wide. It uses dual wheels allowing you to position the trailer in tight areas.
view full answer... - Recommended Bolt On Jack w/ a Wheel for a 3 Inch x 2 Inch Trailer Coupler We've got a couple of options for jacks with a wheel that will bolt to your 3" x 2" trailer tongue. Both have the ability to swivel up when you are towing your trailer. Which one you choose is going to depend on the terrain you store your trailer in. I have listed them below and included a couple of review videos so you can see them demonstrated: Swivel Marine Trailer Jack with Caster Wheel - Bolt On - Sidewind - 10" Travel - 1,500 lbs item # DL67MR Xtreme Off-Road Swing-Up Trailer Jack...
view full answer...
Do you have a question about this Trailer Jack?
Used Items Available
Condition: Installed
Notes: Item has been previously test fitted and has minor cosmetic install marks.
Info for this part was:
Edited by:
Lindsey S
Installed by:
Jeff D
Installed by:
Jacob H
Expert Research:
Jameson C
Video Edited:
Dustin K
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Mike S
Updated by:
Matthew E
Updated by:
Noah M
Updated by:
Manda E
Video by:
Shane H
Written by:
Kristina F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
6/3/2023
I am not sure what happened as it looks like the manufacturer was set to ship out a replacement handle. I will have our Customer Service team reach out to you and we will contact the manufacturer.