Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks Parts DL21754 & DL21755

See what our Experts say about this Dutton-Lainson Boat Trailer Parts

• Are Longer Axles Available For Single Axle Pontoon Boat Trailer
  I did some research on your 1994 Sylvan Pontoon boat and found that the beam is 8-ft. The pontoon boat trailers I was able to find information on said the distance between the center of the bunks for a boat with an 8-ft beam are spaced 72 inches apart. I have attached a photo that shows how the bunks are placed under the pontoons. If your trailer frame is wide enough to be able to place the bunks with those dimensions then you would not need to try and extend the axles. You may want to...
  view full answer...
  
• How Do The Roller Bunks Attach to Roller Bunk Bracket # DL21762
  The roller bunks themselves, like # DL21755, have holes on the bottom at either end. You place a bolt through these holes. The hook part of the bracket, # DL21762, goes around the the bolt underneath the rollers. The slotted portion of the bracket is then bolted to the trailer or existing wooden bunks. The holes are slotted so it can be adjusted higher or lower on the bolts. The roller bunk brackets, # DL21762, are sold in quantities of 1 but a total of 4 are needed to mount a pair of...
  view full answer...
• Can the Dutton-Lainson Bunk Board Bracket DL21762 Rotate to Match Hull Angle
  I apologize for all of the confusion. I can tell you with absolute certainty that the Dutton-Lainson Roller Bunk Bracket, # DL21762, will pivot to allow the roller bunk to conform to the angle of the boat or watersport vehicle's hull. The hook piece at the top of the bracket will pivot at the rivet that holds the hook to the mounting bracket. The hook is not easy to rotate because it is designed to have enough tension to hold itself in place once you set it to your desired angle, but a...
  view full answer...
  
• Connecting Bunk Rollers to Form a 10' Roller on my Boat Trailer
  We have a great solution for you. Using the Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks part # DL21762 and two of the Dutton-Lainson Boat Trailer Deluxe Roller Bunk 5' part # DL21741 you will be able to get the 10' roller bunks you are looking for. These are also available in 4 foot sections as part # DL21740. Some of the factory bunk brackets are welded on and some are bolted on if they are bolted on simply take off the single middle and replace it with two of the...
  view full answer...
• Roller Bunk Bracket Recommendation for Mounting to the Cross Member of a Traile
  The Boat Trailer Roller Bunk Bracket # DL21762 that you referenced would work well as a roller bunk bracket for installing onto the cross member of your trailer. I attached a page that has all of our roller bunks also.
  view full answer...
• What Are Dimensions Of Dutton Lainson Roller Bunk Brackets
  The slots in the Boat Trailer Roller Bunk Bracket, part # DL21762 are 7-1/4 inches long so you will be able to use that length to move the brackets where you need them on your trailer frame. Here are the dimensions of the brackets you may find helpful. I have also included a photo of the bracket you can check out. 10-3/4 Inches Overall length 3 Inches Overall Width 2-3/4 Inches Inside Width 7-1/4 Inches Slot Length 7/16 Inch Slot width 3 Inches from Top of Bracket to the Start of the...
  view full answer...
  
• Roller Bunks And Brackets That Can Be Angled To Fit V-Bottom Boat
  To be able to mount roller bunks to your trailer and allow them to be angled to match the hull of your boat there are rollers and brackets that will work for you. You will need to use the Dutton-Lainson Boat Trailer Standard Roller Bunk, part # DL21755. These are black rollers that are 5-ft long. There are 12 sets of 2 rollers with this set. The brackets that can be used with these rollers is part # DL21762. Four brackets are needed for a pair of roller bunks.
  view full answer...
• Roller Bunk Replacement for 2004 Bear Trailer w/ G3 1860 CCT
  Rollers like the part # DL21741 that you referenced can attach to the top of bunk rollers like you have, or if they need to be replaced we also have swivel hangers you can use as well for install with # DL21762. The roller section referenced is a 5 foot section which we also have 4 foot sections with # DL21740 which you can use to come up with the best length for your trailer.
  view full answer...
• Mounting Brackets for Roller Bunks
  You will still want to use two of the Boat Trailer Roller Bunk Bracket item # DL21762 with the 5' long Boat Trailer Standard Roller Bunks item # DL21755. If you are just mounting the bunks using the bracket you won't have enough support with just one on each side.
  view full answer...
• Recommendations for Boat Trailer Roller Bunks for a 2400 Pound Boat
  First off, there may be a solution to the bunks not aligning with the hull. With the Dutton-Lainson roller bunks we offer, you can also get Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks, # DL21762, for the pivoting black steel roller bunks, or # DL21742, for the galvanized. These brackets allow the roller bunks to be adjusted vertically from the trailer and angled to cradle the boat hull. Neither galvanized roller bunks, # DL21741, and # DL21740, will pivot. But both...
  view full answer...
• Roller Bunks Rated for More Than 1,500 lbs
  There are roller bunks for boat trailers rated for over 1,500 lbs; you could use the Dutton-Lainson Boat Trailer Deluxe Roller Bunk # DL21740, which are rated for 2,500 lbs and install with Boat Trailer Roller Bunk Bracket # DL21762. I've attached links to video reviews of the roller bunks for you to take a look at.
  view full answer...
  
• What Is Center-To-Center Dimension Of Slots On Dutton-Lainson Boat Trailer Roller Bunk Bracket
  I called my contact at Dutton-Lainson and asked about the Boat Trailer Roller Bunk Bracket, part # DL21762. The center-to-center slots on the bracket measurement is 1-1/4 inches. I have attached an updated photo of the bracket with the dimensions noted you can take a look at.
  view full answer...
  
• Recommended Roller Bunks for 22' Pontoon Boat Trailer
  There are a lot of great options for roller bunks for your 22' pontoon boat trailer. I've included a link to our selection of roller bunks below. I recommend the Dutton-Lainson Boat Trailer Standard Roller Bunks # DL21755 for their clean look and high weight capacity. These are 5' bunk boards that have 6 sets of 2 rollers along each board and have a weight capacity of 3,000 lbs. They can be attached to your trailer using existing 2' x 4' bunk boards or with the Mounting Brackets # DL21762....
  view full answer...
• Fitment and Parts Needed To Mount Roller Bunks On a Trailer For a V-Hull Boat
  Yes, you can use the Boat Trailer Standard Roller Bunks # DL21755 on a boat that has a V hull. These can be attached to the edge of 2" X 4" Bunk Boards # CE27820 or to Boat Trailer Roller Bunk Brackets # DL21762. The mounting brackets can be angled to match the angle of your boat to ensure that the weight is evenly distributed across all the rollers.
  view full answer...
• Additional Height of Boat Trailer Standard Roller Bunk # DL21754 When Mounted on Bunk Boards
  The Boat Trailer Standard Roller Bunk # DL21754 is going to add 3" of height to the 2'X8" vertical bunks that you have. We do have the Boat Trailer Roller Bunk Bracket # DL21762 that can be used if you feel that the rollers and bunks would raise the boat higher than you would like.
  view full answer...
• Installation of Boat Trailer Standard Roller Bunks 5 Foot # DL21755
  The 5-foot roller bunks # DL21755 can be attached directly to vertically-mounted 2 x 4 bunk board. I would suggest using stainless steel or galvanized hardware. Another option is to use the # DL21762 brackets, 4 brackets are needed to mount a pair of roller bunks. With the brackets, the bunk can be adjusted vertically and can be angled for a custom fit to your boat hull. I have posted a short video showing how the bunks attach to a 2x4 and to one of the brackets for you to review.
  view full answer...
• What Size Roller Bunks for 16 DLX Carolina Skiff Boat Trailer
  I checked with Carolina Skiff and they were able to give me the trailer specifications for the size 1655 DLX. They recommend that you use 2" x 6" wood, carpet-covered bunks that are 10' 6" long spaced 40" apart when measuring from the outside edge of the bunks. They also require that the front end of the bottom bunk extend past the flat bottom of the boat. If you'd like to stick with the wooden bunks they recommend, we do sell the marine grade carpeting in the 18" width, # CE11349. If...
  view full answer...
• Recommended Roller Bunks To Make Loading and Unloading G3 1710 On Bear Boat Trailer Easier
  Adding roller bunks like the Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers # DL21741 you were looking at are a great option to make loading your G3 boats 1710 on your bear trailer much easier. If you have 10' bunks using two of the # DL21741 to match your bunks is recommended. If you have 8' bunks you will want to use Boat Trailer Standard Roller Bunk - 4' Long- 10 Sets of 2 Rollers - by Dutton-Lainson # DL21754 instead. To attach the roller...
  view full answer...
• Roller Bunk Bracket # DL21762 Recommendation
  For a roller bunk bracket designed for roller bunks you would want a Boat Trailer Roller Bunk Bracket # DL21742. If you wanted a set of roller bunks for this bracket I would recommend the Boat Trailer Standard Roller Bunk # DL21754. I spoke to my contact at Dutton-Lainson and he informed me that the Slotted Bunk Bracket # DL21584 that you referenced was designed to work on wooden bunks and would not be recommended for a roller setup.
  view full answer...
• Dimensions of the Slotted Bunk Bracket for Boat Trailers # DL21762
  The dimensions of the Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks Parts DL21754 & DL21755, item # DL21762, are as listed below. 10-3/4 Inches Overall length 3 Inches Overall Width 2-3/4 Inches Inside Width 7-1/4 Inches Slot Length 3/8 Inch Slot width 3 Inches from Top of Bracket to the Start of the Slots 10-3/8 Inches from Top of Bracket to the End of the Slots
  view full answer...
• What Size Bolts to Use to Install Dutton Lainson Roller Bunks
  There isn't an exact bolt size used to install the Roller Bunk part # DL21755 to the bracket part # DL21762. What I can do is show you a picture that shows all of the dimensions of the # DL21762 that will help you pick out the correct size hardware to use based on your application.
  view full answer...
  
• Roller Bunk Recommendation For Bear Trailer With CCJ G3 Jon Boat
  Since you said the bunks on your trailer are 8 ft long, I recommend two sets of part # DL21754, which are 4 ft long and attach them end to end to your bunks, which would cover the 8 ft span your current bunks measure. If you wish to remove the bunks you currently have you could use a bracket like part # DL21762 to attach the roller bunks directly to the trailer frame. These are sold individually and 4 are needed to mount a pair of roller bunks. If you choose to use two sets of rollers,...
  view full answer...
• Recommended Roller Bunks for 600 lbs. Boat
  The Dutton-Lainson Boat Trailer Standard Roller Bunk # DL21754 has a combined weight capacity of 2500 lbs. for both bunk rollers. They can be mounted right on top of wooden bunks. Also, if you 'd like to remove the wooden bunks that are likely on your current trailer you will need the brackets # DL21762. You will need 4 brackets to mount the two roller bunks. I've attached the review video of the roller bunks for you to look at.
  view full answer...
• Will Dutton-Lainson Boat Trailer Standard Roller Bunk # DL21755 Handle 3000-lb Sea Ray 190
  According to the Sea Ray website (which has an excellent archive section with complete specs) your 1997 model year 190 Bowrider has a dry weight of 2750-lbs. Since the boat's entire weight will never be concentrated in one spot you will have no problem using the Dutton-Lainson Boat Trailer Standard Roller Bunk # DL21755. You can also use multiple sets if you want to. The roller bunks are sold without hardware or mounting brackets; we offer bracket # DL21762 and four are needed for each...
  view full answer...

Do you have a question about this Boat Trailer Part?