CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks - Galvanized Steel - Qty 4

See what our Experts say about this CE Smith Boat Trailer Parts

• What Rollers Would You Recommend For My Ramp For Loading Kayaks
  When designing your new kayak ramp I recommend The Yates Keel Roller for Boat Trailers - TPR - 10" Long - 5/8" Shaft - Blue # YR1000B. They're 10 inches long and fit a 5/8 inch shaft. They're constructed from a thermal-plasticized rubber. It is non-marking, and non-scratching material. They're made in the USA. If you're not wanting to design one yourself I recommend going with The CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5 foot Long - 1,500 pounds - 1 Pair # CE27710....
  view full answer...
• How Would Roller Bunks Install on Karavan Boat Trailer
  Since the picture you submitted belongs to Karavan I can't post it here on our site, but if you check out the attached picture you can see how a very similar trailer had a set of rollers like the part # CE27710 installed. For a set of swivel brackets like what you see in the picture that are holding the bunks you'd then want the part # CE10003G-4. I also attached a couple install video links for you to check out as well.
  view full answer...
  
• Can 5 Foot Roller Bunks & Carpet Bunks be Installed Together
  Sure, if you have the room and you'd like to you can install 5 foot roller bunks and carpeted bunks together: - CE Smith Carpeted Bunk Boards for Boat Trailers - 5' Long # CE27820 - CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long # CE27710 For the roller bunks you'll need CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks # CE10003G-4 along with the appropriate size U-bolts, and I've added a link below to our selection so you can get the right size. The...
  view full answer...
• How to Add Bunk Boards to Malone MicroSport Trailer
  To add bunk boards to the Malone MicroSport Trailer # MPG460G you'll want 2 of the Bunk Kit # MPG561 which actually installs on the crossbars. Since the Malone trailer frames are different you'll need to source U-Bolts to install the CE Smith Bolster and Swivel Bracket Assemblies # CE10003G-4 locally as we don't have any standard-sized U-Bolts that fit the MicroSport.
  view full answer...
• How To Install The CE Smith Roller Bunks for Boat Trailers # CE27710
  If you have adjustable brackets for the bunk boards then you could lower them down and mount the CE Smith Roller Bunks for Boat Trailers # CE27710 directly to them. If you don't have adjustable brackets then you would need to remove the bunk boards and install new brackets like the CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks # CE10003G-4. These brackets can be attached to the frame of the trailer with U-bolts like the CE Smith U-Bolts # CE15283GA-4. You'll want to measure...
  view full answer...
  
• Roller Bunks For Shorelander Boat Trailer And Lund Fury 1600 Aluminum Boat
  You have a couple of options for rollers on your Shorelander trailer. If you want to completely cover the 7 foot bunks you currently have, you can attach a 4 ft roller like part # CE27700, and cut another to cover the 7 ft board. If you do mount the roller bunks to the boards you currently have you will want to make sure your rollers for the bow are adjusted at the proper height to offer support for the boat when loaded. I have attached a link to our boat trailer parts. Another option...
  view full answer...
• Recommendation For Adding Bunks or Rollers to a Calkins Boat Trailer for a 21' Boat
  As far as size is concerned, you want the bunks/rollers to be at least half the length of your boat. Whether bunks or rollers are the better option really comes down to your use. If you take your boat on and off of the trailer quite a bit, then going with rollers would be a good choice. The boat will smoothly roll over the bunks which is easier and less taxing on the hull of the boat. Given the size of your boat you would need to use 3 of each product below: - CE Smith Roller Bunks for...
  view full answer...
• Recommended Bunk Roller Setup For A 5,000lb Boat
  Hey Dan, The roller bunks that we offer max out at 3,000lbs per pair so the only way to make this work would be to install a second set of roller bunks to help distribute the weight between both sets of the # DL21741. You'll most likely need to pick up some extra mounting brackets # CE10003G-4 to secure the second set and possibly move the first set to better distribute the weight across all rollers.
  view full answer...
• Does it Matter Which Side of the Crossmember the Boat Bunk Brackets Install On
  It doesn't really matter which side of the crossmember of the trailer frame the bunk brackets install on. As long as they are torqued down properly either way will be perfectly safe. Since the brackets have swivels like # CE10003G-4 there would be no need to cut the boards at a different angle.
  view full answer...
• Parts Needed to Convert a Boat Trailer From Bunk Boards to Roller Bunks for a 21' Boat
  Each pair of Boat Trailer Deluxe Roller Bunks # DL21740 have a 2,500 lb. capacity. Your bigger consideration will be the length because with needing multiple pairs of rollers, you will have enough weight capacity. Typically you will want to match the length of your current bunks with the news ones. But a good rule of thumb is to have at least 50% of the length of your boat. I have included enough bunk rollers and parts needed for that below. Bunk Rollers - Boat Trailer Deluxe Roller Bunks...
  view full answer...
• Roller Bunk Recommendation for a Boat Trailer with Wood Bunks
  The CE Smith Roller Bunks, # CE27700, that you referenced would be a great option for your boat trailer. These roller bunks are 4 ft long and they can be mounted directly on top of your current wood bunks. You can also use the CE Smith Mounting Brackets, # CE10003G-4, if you want to replace the wood bunks with the roller bunks. Keep in mind, these bunks have a weight capacity of 1,500 lbs, but based on your photo, I do not think you will have much of an issue with that.
  view full answer...
  
• Recommended Roller Bunks For 26' Seaswirl Boat Weighing 4200lbs
  You could absolutely replace your standard wooden bunk boards with the CE Smith Roller Bunks for Boat Trailers - 5 Rollers Each - 4' Long - 1,500 lbs - 1 Pair # CE27700 you were looking at, but since they have a 1500lb rating each you will need to make sure to use at least 3 pairs due to your boat being 4200lbs. These roller bunks will allow you to load your 26' Seaswirl much easier. The easiest way to install these is to just attach them directly to your existing bunk boards, but if...
  view full answer...
• Roller Bunks For 8 Foot Long Bunk Boards on Jet Ski Trailer
  Since you have 8 foot wooden bunks already, you can indeed just mount the roller bunks directly to the wooden bunks with 3/8" lag screws, and you're correct you'd need four of the CE Smith Roller Bunks for Boat Trailers - 4' Long # CE27700. The lag screws are something you'd have to pick up at your hardware store, and that's the route I'd go since it's just easier overall (and just as safe) than removing your current bunks. But if you're more comfortable removing your current bunk boards...
  view full answer...
• Using Roller Bunks for PWC Ramp & Trailer
  Roller bunks like the 5-foot Dutton-Lainson # DL21755 and the other similar products shown on the linked page will work best when they are positioned on the trailer or ramp surface in such a way that allows the maximum contact between the watercraft's hull and the flat top surface of the rollers. The fuller and more even the contact the easier the rolling action will be. On a PWC the hull can have many different profiles or shapes. These can include the common V and modified V, and the...
  view full answer...
• Comparing Dutton-Lainson and CE Smith Roller Bunks
  There isn't a whole lot of difference between Dutton-Lainson roller bunks # DL21741 and CE Smith roller bunks # CE27710. Both have 5 foot long sections. Each section is rated for 1500 pounds. There are 6 rollers per section on both. Both are made with galvanized steel and heavy duty black rubber rollers. The main difference besides price is the shape of the rollers is not exactly the same. Either set can be mounted on a bunk or independently. To mount independently you would need the...
  view full answer...
• What Size Mounting Hole is On Top of Roller Bunk Bracket CE10003G-4
  The hole in the top of the swivel bracket of the bunk bracket part # CE10003G-4 is 7/16 inch in diameter. You would need to go with a nut and bolt that matches that hole size the best when securing your roller bunk to it. We don't have a specific size recommendation as applications can differ.
  view full answer...
• Does Rhino Rack Roof Rack part # RR44SR Come with Fit Kit and Install Hardware
  The Rhino Rack roof rack part # CE10003G-4 that you referenced comes with all needed install hardware and fit kits to install on a vehicle.
  view full answer...
• Converting Bunk Boards to Roller Bunks of 2019 Bayliner 195 Boat Trailer
  I recommend replacing your bunk boards with the CE Smith Roller Bunks you were looking at. We have the following sizes: -CE Smith Roller Bunks for Boat Trailers - 5 Rollers Each - 4' Long - 1,500 lbs - 1 Pair # CE27700 -CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair # CE27710 You can choose the size or a combination of sizes based on the length of your current boards. You have the option to mount these on your existing bunk boards or you can use...
  view full answer...
• Will the CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunk Work On Outside Frame Rails
  The CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks part # CE10003G-4 are designed to be mounted to the horizontal center sections of the trailer also know as crossmembers. These will not work when mounted to the vertical outside frame rails. The swivels would be in the wrong position and the bunk boards would tilt front to back and not side to side. They are designed to be used with the CE Smith Carpeted Bunk Boards for Boat Trailers like part # CE27840.
  view full answer...
• Can Roller Bunks Be Used on Tritoon Boat Trailer
  Roller bunks like those shown on the linked page will work just as well on a 3-hull tritoon as on a pontoon boat. If you intend to mount the rollers onto the flat surface of existing wooden/carpeted 2x4 bunk boards you will want to use a flat-bottom type roller like # DL21741, but we also have rollers like # DL21755 that have a channel that fits over the narrow side of a 2x4. The flat-bottom type can also be directly mounted to bolster brackets like # CE10003G-4 as shown in the linked photo.
  view full answer...
  
• Recommendation for Spool Rollers for 18ft Wood Boat on Custom Boat Trailer
  I do have a solution for you, however the CE Smith Spool Roller Assembly # CE32100G aren't wide enough to safely support the boat keel of your 18 foot Norwegian Faering. I recommend something a bit wider like the CE Smith Deep V Keel Roller Assembly # CE10453G with an 8 inch roller and mounting slots spaced 6 inches apart. You will want to have one for each cross member on your boat trailer. The only other thing you will need are 1/2" or 7/16" fasteners. I have included a video review...
  view full answer...
• Comparing the Dutton-Lainson and CE Smith Roller Bunks
  I would be happy to compare the Dutton-Lainson Roller Bunks item # DL21741 and CE Smith Roller Bunks item # CE27710 but there's not that much of a difference. Both are 5 foot long and have 6 rollers per section. Each section is rated for 1500 pounds. Both are made with galvanized steel and heavy duty black rubber rollers. The main difference besides price is the shape of the rollers is not exactly the same. The CE Smith rollers are more round where the Dutton-Lainson are boxy and almost...
  view full answer...
• How To Install Roller Bunks on a Malone Watersport Trailer
  In order to convert your Malone trailer from a roof rack on wheels to a full on boat trailer with roller guide-on's, I recommend using the CE Smith Roller Bunks for Boat Trailers part # CE27700 and CE Smith Bolster and Swivel Bracket Assemblies for Roller Bunks part # CE10003G-4. The crossbars and brackets will need to removed and then you can install the swivel brackets to the crossmembers and the bunk rollers to the swivel brackets. That said, you will still need u-bolts that match the...
  view full answer...
  
• Are CE Smith Roller Bunk Brackets Compatible with Dutton Lainson Roller Bunks
  Hey Rusty, yes the Dutton Lainson roller bunks part # DL21740 are compatible with the swivel bracket assemblies part # CE10003G-4.
  view full answer...

Do you have a question about this Boat Trailer Part?