What Is Center-To-Center Dimension Of Slots On Dutton-Lainson Boat Trailer Roller Bunk Bracket

Question

Question:

The diagram highlights all dimensions but the slot-to-slot center to center width. I am guessing 1 1/2? Thank you.

asked by: David L

0

Expert Reply:

I called my contact at Dutton-Lainson and asked about the Boat Trailer Roller Bunk Bracket, part # DL21762.

The center-to-center slots on the bracket measurement is 1-1/4 inches. I have attached an updated photo of the bracket with the dimensions noted you can take a look at.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

There are roller bunks for boat trailers rated for over 1,500 lbs; you could use the Dutton-Lainson Boat Trailer Deluxe Roller Bunk #DL21740, which are rated for 2,500 lbs and install with Boat Trailer Roller Bunk Bracket #DL21762. I've…

view full answer...

Answer 2

Two 12 foot long bunks boards will work well to support your 21 foot boat. Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like. Due to…

view full answer...

Answer 3

No worries, you can easily construct some bunks yourself. Go to your local lumberyard and get some treated yellow pine 2x4x10 boards. You can then purchase some of the marine-grade carpet we offer, like part #CE11372. You'll need one roll…

view full answer...

Answer 4

I spoke with my contact at Dutton-Lainson about storing your pontoon boat on the #DL21755 roller bunks. They said there is no problem with storing your boat on the roller bunks over the winter. The bunks have a weight capacity of 3,000 pounds, so…

view full answer...

Answer 5

There isn't an exact bolt size used to install the Roller Bunk part #DL21755 to the bracket part #DL21762. What I can do is show you a picture that shows all of the dimensions of the #DL21762 that will help you pick out the correct size…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

What Is Center-To-Center Dimension Of Slots On Dutton-Lainson Boat Trailer Roller Bunk Bracket

Product Page this Question was Asked From

Continue Researching