Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front
(18 reviews)
Price: $52.59
In Stock
Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front
Item # APS6SE
Our Price: $52.59
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (18)
- Q & A (0)
- Photos
etrailer Trailer Leaf Spring Suspension - APS6SE
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Slipper Springs - 2 Inch
- Single Axle
- etrailer
Kit includes 3-3/4" tall front hangers, 5-1/6" tall rear hangers and hardware for mounting 2" springs to your 2,000-lb to 8,000-lb, single-axle trailer frame. Components for mounting axle to springs sold separately.
Features:
- Attaches 2 leaf springs (sold separately) to your trailer frame
- Use table below to determine hanger location based on type of leaf springs
- Achieves 4-3/4" or 5" clearance between trailer frame and axle, depending on axle size
- Includes:
- (2) 3-3/4" Tall front hangers
- (2) 5-1/6" Tall rear hangers
- (4) 3-1/2" Long x 9/16" diameter shackle bolts
- (4) 9/16" Diameter locknuts
- Designed for use on trailers with single, 2,000-lb to 8,000-lb axles
- Does not include components for mounting axle to springs
| Leaf Springs | A - Distance Between Hangers | B - Distance Between Center of Axle and Trailer Frame | Axle Diameter |
|---|---|---|---|
| SP-230275 (803T3) SP-232275 (1203T3) SP-285275 (1403T3) | 25" | 4-3/4" | 3" (typical 5,200-lb to 7,200-lb trailer axle) |
| SP-160275 (E5226) | 26" | 5" | 3" (typical 5,200-lb to 7,200-lb trailer axle) |
| SP-161275 (E5115) | 28" | 5" | 3" (typical 5,200-lb to 7,200-lb trailer axle) |
Note: The above table provides an indication of where the included hangers can be mounted on your trailer. The distance between the hangers may vary depending on your specific application. Be sure to verify proper positioning before welding.
TSW-S8 Single Axle Hanger Kit - 1.75" or 2" Slipper Springs - 2,000 lbs to 8,000 lbs
Replaces APS6SE
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
Customer Reviews
Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front - APS6SE
Average Customer Rating: 4.8 out of 5 stars (18 Customer Reviews)
Kit includes 3-3/4" tall front hangers, 5-1/6" tall rear hangers and hardware for mounting 2" springs to your 2,000-lb to 8,000-lb, single-axle trailer frame. Components for mounting axle to springs sold separately.by: Tyler05/02/2022
Product serves its' purpose. The steel welded well. I've put 1-2k miles on these hangers so far and they are working correctly.
The bolts are way too short. The threads do not reach through the hanger to start threading the nut. I had to clamp the heck out of each one to get a nut to bite. Had to go to Tractor supply and pick up 2 extra bolts that were 1" longer to even use two of the hangers. Product is good but save yourself some headache and pick up longer bolts before trying to install.
by: Santos 10/23/2022
Excellent product and excellent service. I received my order 2 days earlier than expected! Thank you for your prompt attention!
Santos
10/25/2023
The new leaf springs are excellent. My trailer is now sturdy.Great product!
Mike L.
11/11/2023
@Santos We're glad to hear that!
by: Dennis09/04/2022
Thanks for the followup, Hanger kit arrived on time and worked perfectly.
by: Mike n. Massachusetts 10/14/2016
Purchased eight leaf slipper springs for a logging trailer I am building great quality also got u bolt and hanger kit great prices and heavy duty also fenders very impressed with everything great service and fast shipping I will recommend etrailer to all
by: Mark06/24/2022
Item its great but shipping was so poor, i know the excuse is that “due to covid” but working as a art director in the movie industry i order hundreds of this per week and this is the only company that seems to take this long so I'm thinkIng its management or a problem with the company not the “covid” excuse since every other company i deal with seems to have survived. Oh well good product though
by: Bruce 12/14/2019
great products, fast shipping, great communication and follow up. Huge inventory makes for ease of finding anything trailer related. E-trailer is my best and only source for trailer parts.
by: Kenneth 03/09/2023
first quality
by: Bill08/27/2020
Great service, bolts could be 1/4" longer for easier installation.
by: DAW04/11/2015
Very pleased with the parts. Everything was exactly as described.
by: Alvin 09/01/2021
Good product fast delivery
by: Dwight 10/01/2022
by: Wayne 09/05/2022
by: Robert 10/19/2023
by: Royce10/19/2021
by: Ed03/26/2021
by: Macon08/20/2021
by: Glenn 08/20/2021
by: Steve 10/22/2021
18
18
See what our Experts say about this etrailer Trailer Leaf Spring Suspension
- Dimensions of Hangers Included with Single-Axle Trailer Hanger Kit for 2" Slipper Springs APS6SEThe front hangers in kit # APS6SE are # 721584. They measure 3-3/4 inches from the top to the center of the mounting hole. The hole is 9/16 inches in diameter. The holes that are in the top are not for bolting the hanger. They are there to mount the hangers using button welds. Very few hangers are designed to be bolted on. The rear hangers in the kit are # 721585. They measure 5-1/6 inches tall from the top to the center of the 9/16 inch diameter hole. It also features the 2 holes for...
view full answer...
- Tandem Axle Hanger Kit for 2 inch Wide Slipper SpringsYes, you can mount two 6,000 lb capacity axles that use slipper springs in tandem on your trailer. What you'll need is a tandem axle slipper spring hanger kit like the part # APT6SE which is designed for 2 inch wide springs like what you have. What equalizers do is prevents any of your axles from ever carrying the full weight of the trailer at any time like over a bump. The weight is always "equalized" between the two axles.
view full answer... - Do Leaf Spring Hangers Need To Be Welded To Bottom Of Frame Or Can They Be Welded To The Side?Leaf spring hangers like the Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front # APS6SE you were looking at need to be installed on the bottom of the frame, and installing them on the side of the frame would cause the axle to be the frame. You could fabricate a bump out on the frame to give you a place for the hangers to mount if needed, but I recommend having a qualified welder do the welding as it will be what is keeping your axle connected to your trailer. I...
view full answer... - What to Consider When Lifting a Boat TrailerI would first recommend that you see our article "How to Raise Your Travel Trailer"(linked below). This may help you find the best way to add 2" to your boat trailer. As we do not sell or recommend lift blocks on a trailer. Being that you are asking about lift blocks I am going to assume that your axle is already located below the leaf springs. If not you can use the Over-Under Conversion Kit # K71-384-00 if you have an axle diameter or 2-3/8". For 3" axles use Kit # K71-385-00 to achieve...
view full answer... - How Does the Single-Axle Trailer Hanger Kit #APS6SE Work with 1.75 Inch Slipper SpringsTo assemble a slipper spring suspension system, you'll need several components: the hangers and bolts (included in the kit APS6SE); slipper springs, such as the 1.75 inch # e33SR; spring seats such as # TRSS300; and a U-bolt mounting kit such as # # APUBR-8. The 1.75 inch springs attach the same as 2 inch springs would. The hangers attach the springs to your trailer frame. The U-bolt plates attach the springs to the axle. The spring seat welds onto your axle to provide additional support....
view full answer... - Width of Leaf Springs For Use With Single-Axle Trailer Hanger Kit APS2The Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear # APS2 is designed for use with 1-3/4" wide double-eye leaf springs, so it wouldn't work with 2" wide springs. Double-eye springs are standard 1-3/4" and the only hanger kits we have for 2" springs are for slipper springs. If you have 2" slipper springs instead of double-eye springs you can use the Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front # APS6SE.
view full answer... - Upgrading Tire Size and Suspension on a Homemade Hovercraft TrailerThe wheels that are currently on your tires are 3-3/4 inches wide, but the width of the actual tire (section width) will be greater. The section width of your 4.80/4.00-8 tires is 4.6 inches. Moving up to a 6 inch wide, 10 inch diameter wheel like the Kenda 205/65-10 Tire and Wheel Combo 4 on 4 Bolt Pattern, # AM3H460, will have a section width of 8.07 inches. This will bring the tire approximately 1-3/4 inches closer to the trailer frame leaving a 1-3/4 inch gap. This will be plenty...
view full answer...
- Best Parts to Upgrade a Harbor Freight TrailerI can confirm that the parts listed below are all compatible. I do recommend replacing your spring hangers since you are upgrading everything else on your suspension. The Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front item # APS6SE will work great with your springs. Dexter Idler Trailer Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs item # 20545I-EZ-60-10 Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel - 5 on 4-1/2 - Load...
view full answer... - Which Trailer Suspension Hanger Kit Do I Need For 27 Long x 2 Wide Slipper Spring On 6000-lb AxleTo mount your 27" long slipper springs # e67SR you'll need to choose between a kit for single axle trailers or a tandem axle trailer. If you have a single axle trailer you'll want to use the Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front # APS6SE. If you have a tandem axle trailer you'll want to use the Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers # APT6SE. Since these kits do not come with the mounting bolts to secure the springs...
view full answer... - Thickness of Metal of Single Axle Hanger KitThe metal is 3/16" thick on the hangers in the Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front # APS6SE.
view full answer... - Bolts Needed To Install Slipper SpringsFor the spring eye you would use the Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long # 166079, but slipper springs don't have the second spring eye, so a bolt is not used on the back end. You can also use a wet bolt like # 126B2, for less friction. The Shackle Bolt with Locknut for Double-Eye Springs - 3" Long # 166081 are for use with the spring and shackle straps used with a shackle straps on a tandem setup with an equalizer but it could be used for the springs and the...
view full answer... - Axle Recommendation for a Trailer for Best Ground ClearanceActually if you are looking for the best possible ground clearance for your trailer a Timbren Axleless system with a lift built into it like the part # ASR3500S06 would be your best option. Not only will there not be an axle running down the middle of your trailer which would limit ground clearance, but the spindles have a lift built into them to give even more ground clearance than a standard axle or torsion axle. This system has a 3,500 lb capacity as well.
view full answer...
Do you have a question about this Trailer Leaf Spring Suspension?
Info for this part was:
Updated by:
Lindsey S
Updated by:
Alexander C
Expert Research:
Michael H
Expert Research:
Jameson C
Installed by:
Jeff D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Tyler
5/3/2023
They are still holding good. I get a sick feeling every time I see the connections with the bolts that are too short. There is just something unsettling about the nut not even threading enough for the bolt to protrude the other side.