Pollak Circuit Breaker - Cycling/Automatic Reset - 20 Amp - Straight Mount Bracket

See what our Experts say about this Pollak Accessories and Parts

• Hooking Up Lights for Inside and Enclosed Trailer
  The easiest way to do this would be to run a wire to the positive battery terminal, via a 20 amp inline circuit breaker, item # PK54520.
  view full answer...
• How to Install the Replacement Electric Jack Switch with Harness # LC387874
  I have attached a diagram that demonstrates how the typical wiring will need to be installed for the Replacement Electric Jack Switch with Harness # LC387874 that you referenced. Black Wire - Ground Battery Red Wire - Power Battery (20A Auto Reset Breaker # PK54520 will need to be installed in-line) Yellow Wire (Retract) - Black Motor Wire Blue Wire (Extend) - Red Motor Wire (6A Auto Reset Breaker # LC134181 will also need to be installed here)
  view full answer...
  
• Does a 7-Way Trailer Connector on a 2007 Volvo XC90 Have to be Fully Functional for a Prodigy RF
  For the Prodigy RF # TK94FR two work the only functions that need to be active are the lighting circuits and the 12 volt circuit. The 12 volt circuit actually powers the RF so it must be installed. To make it active you will run the 12 volt circuit wire from the back of your new 7-Way connector, under the vehicle using about 20 feet of # 10-1-1 wire, and into the engine compartment near the battery *unless the vehicle battery is located elsewhere then you would run it to that location instead). Make...
  view full answer...
• Tekonsha Voyager Not Sending Power to the Trailer Brakes
  The Adapter # 3034-P that you referenced is the correct adapter to connect the Tekonsha Voyager # 39510 to your RV on a 2017 Ford E-450 Chassis. The part of your description that sounds like it is the problem is where you say the Black wire grounds into the Blue wire - this should not be the case and is most likely your issue. The Black, White, Blue, and Red wires from the Voyager should be connected to the following functions: Black - Battery for Power (20 Amp Circuit Breaker # PK54520...
  view full answer...
  
• Installing a Tekonsha P2 Electric Trailer Brake Controller # 90885 on a 2004 Hummer H1
  To install the Tekonsha P2 Brake Controller # 90885, in your 2004 Hummer H1, you will need to do a little hardwiring, but since you already have a functioning 7-Way trailer connector, there will not be too much work involved to get it installed and ready to tow. First, you will need enough wire # 10-1-1 to reach from the 7-Way trailer connector at the back of the H1 to the cab of the vehicle where you plan to mount the brake controller. This wire is sold in 1-foot increments. I recommend...
  view full answer...
• Where are Circuit Breakers/Fuses Installed on Lippert Electric Stabilizer Jacks
  The Lippert stabilizer jacks like you have use an 6 amp auto reset circuit breaker and a 20 amp fuse or breaker. If you check out the diagram I attached you'll see how it normally would be wired. For a 20 amp breaker you'd need the part # PK54520 and for a 6 amp breaker part # LC134181. If somehow the motors are bad they are part number # LC138445.
  view full answer...
  
• Installation Of The Redarc Tow-Pro Elite RED44FR For 2022 Subaru Ascent?
  Yes, whoever it is that told you about the Redarc Tow-Pro Elite Trailer Brake Controller, # RED44FR has definitely made a great recommendation to you, absolutely this will work in your 2022 Subaru Ascent. The installation process depends if your Ascent is equipped with the factory tow package. If your Ascent has the factory tow package you will be able to use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, # 3062-P. This plugs into the factory trailer brake controller...
  view full answer...
• Installing an Electric Trailer Brake Controller on a 1997 Winnebago Motorhome
  To install the Tekonsha P2 Brake Controller, # 90885, on your 1997 Winnebago, you will most likely have to hardwire the controller. You will need the controller and a 7 and 4 Way Installation Kit, # ETBC7. If the Winnebago has a 4-Way then it will be a little easier to install. If it does not, there is just a little more hardwiring that will need to be done. If the Winnebago has a 7-Way, you will need the controller and Universal Brake Control Wiring Kit for 2-8 Brakes, # 5506, a 40-amp...
  view full answer...
• Troubleshooting No Power to Prodigy P2 Brake Controller Installed in 2012 Dodge Journey
  It sounds like your Prodigy P2 trailer brake controller # 90885 may not be getting the 12V operating power from the Journey's battery. With a hardwired type of installation this input power is routed from the battery positive terminal through a circuit breaker and on to the controller's black power wire. It is possible that if your installation used a non-resetting circuit breaker that the breaker could be tripped/bad. You can use a circuit tester like # PTW2993 to check for power on...
  view full answer...
• Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
  The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, # HA100400C. This unit connects to the air brakes on the truck and when the brakes are applied it sends an electric signal back to the trailer brakes. The other option, and what I would do, is to use an electric brake controller like # 90885. For either of these controllers, the red wire attaches...
  view full answer...
• What Size Wire Should be Used for Wiring the Blue and Black Brake Controller Wires
  We actually sell a duplex cable that would be perfect for this application. Take a look at Jacketed 2 Wire, 10 Gauge, Brake Wire, # 10-2-1. This is a jacketed wire with 2 wires inside, both are 10 gauge wires. It is sold in 1 foot increments so if you needed 32 feet, enter 32 as the quantity. We actually use this wire in our 7 and 4-Way Installation Kit, # ETBC7, which is for hardwiring brake controllers. You also may need either a 20 amp circuit breaker, # PK54520, or a 30 amp circuit...
  view full answer...
• Adding Electrical Connector for Wash Down Pump on a 2005 Dodge Ram 1500
  I have a simple solution that I think you will like. All you will need is some 10 gauge wire, # 10-1-1, and some quick connectors, # DL24085. For the wire you will change the quantity to the amount of feet you will need which will depend on where you want the connector to go on the truck. You would attach the power (and ground if applicable) wires to one of the connectors from the pump. The other connector will use the 10-1-1 wiring and will need to connect to the positive battery terminal...
  view full answer...
• Wiring In-Bed Truck Camper Running Lights and 12 Volt Circuit to 2012 Toyota Tacoma
  Tapping into the vehicle's 4-Way trailer connector for running lights will work great. It is the pin next to the ground pin, usually a brown wire. The aftermarket 4-Ways for the 2012 Toyota Tacoma are all going to be circuit protected so you would not have to worry about that circuit causing any trouble with the vehicle wiring. You would not have to use diodes for the 12 volt circuit. What I recommend is 10 gauge wire, # 10-1-1 sold by the foot, and a circuit breaker such as # PK54520...
  view full answer...
  
• Is There a Replacement Circuit Breaker Available for the Ultra-Fab UF38-944017 Jack?
  We do indeed have replacement 20-Amp circuit breakers, like the Pollak Circuit Breaker - Cycling/Automatic Reset - 20 Amp - Straight Mount Bracket # PK54520, but the Auto-Reset Circuit Breaker for Ultra-Fab 3,500-lb Electric A-Frame Jack UF38-101238 is no longer available, unfortunately. Though this will not be a direct replacement available from Ultra-Fab, it will definitely work with your # UF38-944017.
  view full answer...
• Installation of Power Wire to Brake Controller and 7-Way Connector on Motor Home
  The connection you will need to use is most likely the chassis connection in the case of the brake controller. You will want the connection that is hot at all times ran to the brake controller so that the trailer brakes can be operated at any time whether the ignition is on or not. The brake controller should be wired through at least a 20 amp circuit breaker, item # PK54520, and a 30 amp circuit breaker, item # PK54530, if the trailer has more than 4 brakes or the brake controller calls...
  view full answer...
• Draw-Tite Brake Controller # 5504 Does Not Have Power After Switching Out Goosenecks on a 1999 Z71
  First thing you need to do is trace back and make sure your Draw-Tite Controller # 5504 is properly and securely hooked up. Your issue sounds as if your black 12V POWER wire has come loose and is not pulling the voltage. I have attached the installation directions as well as the wiring diagram; however, I will briefly go through them. Start with your black wire; it needs to run from the brake controller to the 20A Auto-Reset Circuit Breaker, such as Pollak # PK54520. The red wire runs...
  view full answer...
  
• Adding a 7-Way Trailer Connector to a 2005 BMW X3
  If the trailer you plan to tow has a 7-Way round pole connector, you can install a matching connector on your 2005 BMW X3. But an adapter to go from a 4-Way flat to a 7-Way round pin is not available. Below I have explained how to install a 7-Way round pin connector on the vehicle, but it may be much easier to install a 7-Way blade connector on the trailer using # PK12706. You can use the wiring diagram I have linked to wire the 7-Way blade correctly. I have also included a video that should...
  view full answer...
• Size of Circuit Breakers to Use To Install 7-Way Trailer Connector on 2012 Chevrolet Equinox
  If you are installing a 7-way and brake controller you will want to use a circuit breaker in-line when connecting the Black wire from the 7-way to the battery and in-line from the brake controller to the battery. The Black wire will draw 12 volt power. For the Black wire that connects from the rear of the 7-way to the battery it is recommended to use a 40 amp circuit breaker, part # PK54540. The Black wire running from the brake controller to the battery should also have a circuit breaker...
  view full answer...
  
• Does the Prodigy RF Brake Controller Need Brake Output and Reverse Lights Circuits to Work
  Since you are using the Prodigy RF brake controller # TK94FR you will only need to have the 4-Way plugged into the adapter, the white wire grounds to the vehicle frame, and the black wire needs to have power because that is where the RF gets its power. The blue and yellow wires on the adapter, # C57674, will not be used for the RF. But if your trailer has an electric reverse lock out then you would have to attach the yellow wire to a reverse light wire on the vehicle The black wire is...
  view full answer...
• Bully Brake Controller Wiring on a 2009 Chevrolet Silverado
  I have wired a Bully TC-301 Brake controller before and the wiring is as follows. Black = Negative Battery Terminal Red = 12 Volt Constant Power from the Battery Blue = Stop Light Switch Yellow = Power to the Trailer Brakes When connecting the constant power wire from the battery to the Red wire on the brake controller use a 20 amp circuit breaker, item # PK54520. You may also need the Twist-in, 7-Pole, RV-Style Trailer Connector for Chevy and GMC Vehicles, item # PK110916, if your truck...
  view full answer...
• Wiring A 2008 Toyota Highlander for Towing a 1996 Flagstaff Cobra Camper with 6-Way Square Connector
  Jayco uses a different wiring code than most, so in all likelihood, it will not work. I would just cut off the 6-Way square, tape off the brake and battery wires, and connect the 4 wires to a new 4-Way flat connector like part # 9653P. A better solution may be to install a more common 6-Way Round trailer connector on the vehicle and trailer. You could use the Pollak 6-Pole, Round Pin, Trailer Wiring Connector, item # PK11604, on the trailer end and a 4 Pole to 6 Pole Adapter, item # A10-6034VP....
  view full answer...
• Brake Control Installation Instructions for a 1996 Chevrolet C/K Pickup
  You will need to hard wire the Tekonsha # TK63VR, on your 1996 Chevrolet CK Pickup. Hard wiring is straight forward and fairly easy to do. We have instructions and a video that I have linked below for you. From the Brake controller here are your connections. White wire to negative battery post. Black wire through a 20-amp circuit breaker, item # PK54520 (included in kit), to the positive battery post. Red wire to the stop light switch wire behind the brake pedal, use a circuit tester,...
  view full answer...
• Brake controller Installation with OEM Chrysler Wiring Harness Installed
  I would recommend the Tekonsha Prodigy Proportional Brake Controller, item # 90885, for your vehicle. This is one of our best selling proportional units and it will help conserve the brakes on the trailer and vehicle by applying the appropriate amount of braking pressure to the trailer brakes based on your settings and the speed which the vehicle is decelerating. This controller has a digital display and a manual brake lever to power the trailer brakes. If you had a 7-Way wiring harness...
  view full answer...
• Installation of a Pinnacle Draw Tite Brake Controller On a Land Rover Defender
  The blue wire is the trailer brake feed that is wired to the trailer connector at the back of the vehicle. A 10 gauge wire, item # 10-1-1, is used for this connection. The red wire is connected to the cold side of the brake pedal switch. Use a circuit tester, item # 3808, to find the circuit that is hot only when the brake pedal is pressed. The white wire goes to a secure vehicle ground or the negative battery post. Finally the black wire goes to the positive vehicle battery post through...
  view full answer...

Do you have a question about this Accessories and Part?