How to Install the Replacement Electric Jack Switch with Harness # LC387874
Question:
Can you tell me which wire goes where. Trying to do it myself. Which is Pos and negative .
asked by: Duane B
Expert Reply:
I have attached a diagram that demonstrates how the typical wiring will need to be installed for the Replacement Electric Jack Switch with Harness # LC387874 that you referenced.
Black Wire - Ground Battery
Red Wire - Power Battery (20A Auto Reset Breaker # PK54520 will need to be installed in-line)
Yellow Wire (Retract) - Black Motor Wire
Blue Wire (Extend) - Red Motor Wire (6A Auto Reset Breaker # LC134181 will also need to be installed here)
Products Referenced in This Question
Replacement 6-Amp Auto Reset Breaker for Lippert Power Stabilizer Jack
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Breaker
- Lippert
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 20 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 20 Amp
- Pollak
more information >
Product Page this Question was Asked From
Replacement Electric Jack Waterproof Switch with Harness for Lippert High Speed Stabilizer Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Switches
- Lippert
more information >
Continue Researching
- Shop: Replacement 6-Amp Auto Reset Breaker for Lippert Power Stabilizer Jack
- Q&A: What is the Difference Between the 2 Breakers Needed to Install a Lippert Electric Jack Switch
- Shop: Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs - Black
- Shop: Pollak Circuit Breaker - Cycling/Automatic Reset - 20 Amp - Straight Mount Bracket
- Shop: RV Landing Gear Switch - 12V - Black
- Video: Stromberg Carlson Electric Trailer Jack Review JET-3755
- Search Results: electric jack motors
- Q&A: How to Connect Replacement Switch for 3,500 lb RAM Electric Trailer Jack
- Q&A: Can the Stromberg Carlson Electric Jack Part # JET-3755 Draw Power from the Vehicle's Battery
- Q&A: How to Wire the Toggle Switches on the Lippert Electric Trailer Jack LC285318
- Q&A: What Is This Part W/ Two Threaded Studs In My Stromberg Carlson Electric Trailer Jack JET-3755?
- Q&A: Wiring Diagram and Fuse Location for the Lippert Ground Control 3.0 4-Point Leveling System
- Q&A: Wiring Guide for Installing 5th Wheel Landing Gear Motor Switch
- Shop: Seaflo Diaphragm Pump for Boats and RVs - Variable Flow - 3 GPM - 55 psi - 12V DC
- Shop: Seaflo Diaphragm Pump for Boats and RVs - Variable Flow - 3 GPM - 45 psi - 12V DC
- Shop: Seaflo Accumulator Tank for RV and Boat Water Pumps - 0.75 Liter
- Video: Review of Seaflo Boat Accessories - Accumulator Tank - SE38FR
- Video: Seaflo Marine and RV Water Pumps Accumulator Tank Review
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: 5 Tips to Confidently Choose Your Weight Distribution Hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: 44649
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: B and W Hitch Ball - Trailer Hitch Ball - BWHB94005 Review
- Shop: Trailer Wiring
- Shop: Fifth Wheel Hitch
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Search Results: 68149
Richard V.
7/11/2020
The wiring is schematic is excellent but i have a jayco eagle ht fifth wheel the wires have rotted off cannot figure where they go, the wire broke at the connector no vinyl left my jacks also work with a remote that's the puzzling part any help is appreciated