Draw-Tite Ball Mount - 3" Rise, 4" Drop - 8-1/2" Long - 12,000 lbs

See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Trailer Hitch, Wiring Harness and Ball Mount Recommendations for 2015 Hyundai Santa Fe Sport
  The Curt Class III hitch you referenced, part # C13152 would be an excellent choice. For wiring, the Curt # C56332 would work well as long as the connectors you found at the rear of the vehicle are active. I'd recommend having a helper activate the turn signals, brake lamps and running lamps as you use a circuit tester like # PTW2993 on the pins of the connectors you found to make sure they're active. If they're not, you'll want to go with the # C56184 wiring harness. When we installed...
  view full answer...
• Shortest Available 2-Inch Ball Mount
  You can see all fixed 2-inch ball mounts by clicking on the linked page. The shortest of these is the Curt Ball Mount # C74WR. This aluminum ball mount measures 8-1/2-inches from the center of the hitch pin hole to the center of the ball hole. It offers either 2-inches of drop or 1-inch of rise. Tow rating is 8K and tongue weight is rated at 800-lbs. A video is linked for you.
  view full answer...
• Difference In Draw-Tite Class IV Hitch Compared To Lower Priced Class IV Hitch
  When comparing the Draw-Tite Ultra Frame Trailer Hitch Receiver - Class IV, part # 41929, to the Curt Trailer Hitch Receiver - Class IV, part # 14361, they are similar, but the new version of the Draw-Tite # 41929 is rated higher. The Draw-Tite Class IV Hitch has a tongue weight capacity of 1,200 pounds and towing capacity of 12,000 pounds. The Curt Class IV Hitch has a tongue weight capacity of 1,000 pounds, and towing capacity of 10,000 pounds. Both part # 41929, and part # 14361 have...
  view full answer...
• Fit of Draw-Tite Class IV # 41936 Trailer Hitch on 2008 Dodge Ram 1500 Mega Cab
  For a Class IV hitch, I'd recommend the Draw-Tite # 41929. The Draw-Tite Class IV hitch you referred to, part # 41936 is a fit for cab and chassis trucks only. Cab and chassis trucks have a narrower frame than the regular truck models do, and therefore the hitch wouldn't fit your truck. I've linked you to the installation instructions. For a 12K rated ballmount, I'd recommend # 4281. For a 12K rated 2-5/16 inch ball, use # 19286 or # A-90 for a 2 inch ball.
  view full answer...
• How to Select a Ball Mount or Draw Bar with the Correct Ball Hole Size 1-1/4"
  This is a great question! Although we do list the ball hole diameter in the specs for each ball mount, there is an easier way to make sure a ball mount has the hole size you need. Any ball mount rated for Class IV hitches will have a 1-1/4" ball hole. As you have discovered, ball mounts rated for Class III hitches can have either a 1" or a 1-1/4" ball hole. If you stick with Class IV ball mounts you can be sure they will have the correct ball hole diameter and they will fit 2" hitches that...
  view full answer...
  
• How Close To a 3" Rise Ball Mount For 2" Receiver Do I Need?
  The Draw-Tite Ball Mount for 2" Hitches # 2753 will work just fine for your situation. I wouldn't be to overly concerned over a 1/4" difference in the height measurement. I usually suggest to be plus or minus 1" for the height. This ball mount is rated for 7,500lbs towing and 750lbs tongue weight. You will need a 2" Hitch Ball # 63845 or 2-5/16" Hitch Ball # C40007 with a 1" shank. If you are concerned we do have the Draw-Tite Ball Mount # 4281 that is a 3" rise. This ball mount is rated...
  view full answer...
• What Ball Mount and Suspension Kit for Towing 2000-lb Trailer with 2013 Toyota Highlander SE Model
  A ball mount with rise or drop is helpful in matching the different heights of the trailer hitch on a tow vehicle and the coupler on a trailer. It is important that your trailer frame be level when hitched to your Highlander to ensure stability when towing. Please note that a different height ball mount will not reduce rear-end sag in your tow vehicle; but we do offer suspension products that will help. We offer a wide range of both fixed and adjustable ball mounts (the adjustable type...
  view full answer...
• Availability of Reese Class IV 2 Inch Hitch For 2008 Dodge Ram Quad Cab
  I do have a Reese Class IV 2 inch hitch for your 2008 Dodge Ram Quad Cab, but it will not fit a Mega Cab. You can use It Draw-Tite Class IV 2 Inch Hitch, part # 41929. This hitch has a gross trailer weight capacity of 12,000 lbs, 15,000 lbs with weight distribution, and a maximum tongue weight capacity of 1,200 lbs, 1,500 lbs with weight distribution. If your Ram has an factory hitch this Reese hitch is designed to fit underneath the factory hitch. I am including a link to the installation...
  view full answer...
• How to Pick Out the Correct Rise Ball Mount for a 2007 Volvo XC90 towing a Boat Trailer
  I attached an FAQ on determining the correct rise/drop ball mount for you to check out, but it sounds like you have determined that you need a ball mount with a 3 inch rise. Check out the Draw-Tite Ball Mount # 4281, when used in the rise position this ball mount will give you 3 inches of rise. What hitch do you have? Thule does not make hitches for vehicles so I am wondering if you meant to type Valley. The reason I ask is that because all of the hitches we offer for your vehicle recommend...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?