How Close To a 3" Rise Ball Mount For 2" Receiver Do I Need?

Question

Question:

I need a ball mount for a class III hitch with 2inch receiver. Based on my measurements I need a 3inch rise. It seems like the closest I can find in terms of rise is a 2 3/4inch like this one. How much difference would the 1/4inch difference make? Could I safely use this, or do I need to search harder for an exact 3inch rise?

asked by: Matt

0

Expert Reply:

The Draw-Tite Ball Mount for 2" Hitches # 2753 will work just fine for your situation. I wouldn't be to overly concerned over a 1/4" difference in the height measurement. I usually suggest to be plus or minus 1" for the height. This ball mount is rated for 7,500lbs towing and 750lbs tongue weight. You will need a 2" Hitch Ball # 63845 or 2-5/16" Hitch Ball # C40007 with a 1" shank.

If you are concerned we do have the Draw-Tite Ball Mount # 4281 that is a 3" rise. This ball mount is rated for 12,000lbs towing and 1,200lbs of tongue weight. It will require a 2" Hitch Ball # A-90 or 2-5/16" Hitch Ball # C49FR with a 1-1/4" shank.

expert reply by: Bud M

0

Answer 1

This is a great question! Although we do list the ball hole diameter in the specs for each ball mount, there is an easier way to make sure a ball mount has the hole size you need. Any ball mount rated for Class IV hitches will have a 1-1/4" ball…

view full answer...

Answer 2

In most cases it's a bit safer to go on the slightly lower nose height setting instead of slightly higher since higher can sometimes cause sway. But if the vehicle is going to squat quite a bit from the weight of the trailer then the higher would…

view full answer...

Answer 3

A great majority of standard ball mounts are designed so that they can be used in either the drop or rise position. Using a ball mount like the Draw-Tite #2753 that you were looking at in the rise position is just a matter of turning it upside down…

view full answer...

Answer 4

The Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K #2753 is not the correct fit for zero rise or drop. For the zero rise or drop you will need the Curt Solid 2-Ball Mount for 2" Hitches - 2"…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...