Replacement Switch for Stromberg Carlson Electric Landing Gear
(56 reviews)
Price: $74.61
In Stock
Replacement Switch for Stromberg Carlson Electric Landing Gear
Item # LG-145236
Retail:$80.32
Our Price: $74.61
You Save: 7%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (56)
- Q & A (0)
- Videos (1)
- Photos
Stromberg Carlson Accessories and Parts - LG-145236
- Camper Jacks
- Trailer Jack
- Switches
- Stromberg Carlson
Replaces the IP-rated switch for your Stromberg Carlson electric landing gear set (LG-1, LG-2, LG-3, or LG-4).
Features:
- Replaces the IP-rated switch for your electric, tandem landing gear
- Designed for use with Stromberg Carlson models LG-1, LG-2, LG-3, and LG-4
- Can be used with most electric landing gear sets, including Atwood, Venture, and Lippert models
- Switch measures 2-1/4" long x 3-1/4" wide
- Arc resistant switch
- Mounting hardware included
- Made in the USA
LG-145236 Stromberg Carlson Replacement Venture IP Rated Switch for Fifth Wheel Landing Gear
Installation Details
California residents: click here
Video of Replacement Switch for Stromberg Carlson Electric Landing Gear
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Stromberg Carlson Trailer Jack LG-145236 Review
Today we're going to review part number LG-145236. This is the Stromberg Carlson Replacement Switch for the Stromberg Carlson electric landing gear. This part will replace the IP-rated switch for your tandem landing gear. It is designed for use with the Stromberg Carlson LG-1 landing gear, and we do sell that product separately on our website. The switch is a toggle switch as you can see. When you push it, you can extend, and push it to retract.
It does come with about a 4' length of wire and it comes with the wires to connect to the motor, and then the wires to connect to the power source. This will also work with most other brands of electric landing gear including Atwood and Lippert. Comes with everything shown here, the switch with the harness, the instructions and set of screws for mounting it. The switch, give you a measurement. On the mounting bracket itself is 2 1/4" wide by about 3 1/4" tall. That should do it for the review on part number LG-145236.
This is the Stromberg Carlson Replacement Switch for the Stromberg Carlson electric landing gear.
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- etrailer mistake
- Alternate product found
- Arrived Damaged
Customer Reviews
Replacement Switch for Stromberg Carlson Electric Landing Gear - LG-145236
Average Customer Rating: 4.9 out of 5 stars (56 Customer Reviews)
Replaces the IP-rated switch for your Stromberg Carlson electric landing gear set (LG-1, LG-2, LG-3, or LG-4).by: Jimmie D03/10/2023
Service was very quick and it was shipped in a few hours after I ordered it. Part was spot on!!
by: Steve S.04/27/2015
Top notch quality, and great service.
These parts were used to upgrade a 5th wheel camper with manual crank for the landing legs. The motor fit perfectly my Atwood landing legs gear drive, and the switch was an easy install, with good directions on wiring install.
They are working like a champ. Thak goodness, there will be no more manual cranking of the landing legs for me… ;)
by: Kevin04/27/2018
Bought these to run dual landing gear motors. Switch was pre wired for reverse polarity motors, making install easy. Fast shipping and well made.
by: Terry 09/28/2023
Great customer service. Chelsea is very knowledgeable about the replacement part that we needed. Super quick at processing the order and getting the items ordered, to us earlier than expected. Excellent!!!
by: Michael04/28/2023
Gear box worked great. It was the legs that was the problem. Replaced the legs with the bulldog individual leveling and everything is working great.
by: Matt W09/11/2016
Switch is exactly what I needed. I bought my fifth wheel camper used and the original owner must have added the power feature to the landing gear. He used a regular DPDT toggle switch and cobbled up a mount. Switch was not rated high enough for the max DC amps that the landing gear motor was rated for. I decided that I needed to install a proper landing gear switch kit and etrailer's experts answered my product question promptly as this was the only switch that was listed as weatherproof. I needed to install in existing switch location and did not have a switch compartment. Switch seems quality and is proper rated to handle the landing gear motor. Wires are heavy gauge also which I like. It seems that my landing gear travels faster than it did with the old switch and lighter gauge wiring.
Matt W.
9/11/2017
Works the way it should. Nice to not burn out an underrated switch twice a season. Has worked flawlessly for over a year. Rain or shine.
by: Floyd04/04/2018
etrailer got my order late on a Friday, mailed it on Saturday and sent me tracking info. Great service. My landing gear was not a Stromberg Carlson, so I had to drill a couple of hole, shorten some really long wires, and reverse the wires to the motor, but it all worked fine and solved my problem. Very grateful for having it behind me in such a short time.
Floyd
4/4/2019
Have not used it for about 3/4 of the past year, but assume that it still works fine. Thank you for your excellent service
by: Bruce04/12/2019
Installed new switch yesterday,exact match and easy to install. Product received in less than a week . E trailer is great a company and Crystal was very impressive to work with,knowledgable, polite and polite. She is an asset to your company. Will definitely use e trailer whenever needed !
Bruce
4/12/2020
Still working flawlessly,will definitely use your company again when needed
by: William09/03/2023
Outstanding Performance
by: Ken 11/10/2022
Switch works well. However, no wiring instructions were included. I wired red-red, and black-to-black. This caused jacks to go up when pressing down. A quick wiring switch made everything work correctly. Flawless ever since.
by: Keith04/08/2019
Product recommended was perfect fit for my 2007 5th wheel. Fast shipping. All parts and hardware included. Easy installation to replace my existing landing gear, motor and switch. Great company to buy from. Thanks Etrailer
by: Michael 06/08/2020
Product was top-shelf quality and a huge improvement over the OEM switch my Geneisis Supreme came with. E-Trailer was terrific to deal with and order shipped promptly. If you need a replacement Landing Jack switch, this product will satisfy!!!
by: Duane08/26/2016
This hard wire harness worked perfect for the application and I was able to connect it in about 5 minutes
by: John P.06/29/2015
Fast shipping. Improved quality switch with instructions included.
John F.
6/28/2016
This switch is very well made and is superior to the OEM jack switch I replaced on my fifth wheel.
by: Paul10/04/2016
At the time I traded the 5th wheel in they were performing as advertised.
by: Billy W11/08/2013
Excellent, Better Than The Original Equipment.
etrailer.com is an exceptional place to buy parts, everything was as they advertised . service and delivery was very good.
keep up the good work,nice to deal with you folk, will use in future.
by: Donna12/20/2018
So far so good. Fifth wheel jack switch is working well.
by: Michael09/11/2018
I replaced a lesser quality switch with this one and could not believe the difference it made. It's as though the previous switch was not letting full electrical current through to the motor. Now the motor is quieter and appears to work easier.
by: DeanJ 10/14/2018
Heavy Duty wiring , everything you need to replace the jack switch on a 5th wheel rv
by: Dennis02/10/2019
Replaced switch for jacks on front of fith wheel. Colored coded to match old switch which made it an easy change out.
by: Mark546106/24/2016
Out of the box the item looks like a direct replacement for the bad switch. It was nice to see a wiring diagram included with the package.
by: Darrell05/31/2019
I installed the switch and ran the wires like the drawing showed and it works fine, goes up and down like it used to. Thanks, Will buy from again. Darrell
.
by: Richard D08/26/2017
Haven't installed it yet... but appears to exactly match previous switch that I installed... now both jacks will be independently controlled. Fast service too!
by: Bob W04/22/2017
Easy installation, works great...better than the original switch.
by: Tony B11/10/2017
Perfect fit, works great.
Great Company to deal with.
Tony B.
11/10/2018
Its been a year, and the switch is working great. No failures, or sticking. Id definitely buy from here again.
25
56
Show More Reviews
See what our Experts say about this Stromberg Carlson Accessories and Parts
- Replacement Switch For 5th Wheel Landing GearWe do indeed have replacement switches for 5th wheel landing gear. There is a switch that is universal for landing gear as well, which has the retract and extend functions: - Replacement Switch for Stromberg Carlson Electric Landing Gear # LG-145236 While the # LG-145236 says it is "for Stromberg Carlson" it can be used on all standard 5th wheel landing gear.
view full answer... - Will etrailer Landing Gear RVLG-8000 Fit a 1994 Terry 5th Wheel TrailerLanding gear set # RVLG-8000 will likely fit your 1994 Terry 5th wheel trailer. The size of the jack tubes are standard for 5th wheel jacks and the stop in the legs for the frame clamps have a standard spacing. I have included a picture showing the stop measurements on the legs so you can compare that to your existing set. If that and the other measurements match up then this kit is a great option. The hand crank is available as a separate item and is part # RVLG-HDL. Or you can add a...
view full answer...
- Replacement Landing Gear Switch for Model Number 1A065012-02-01The correct replacement switch for your electric landing gear model number 1A065012-02-01/1-065-041012-01 is the Stromberg Carlson Replacement Switch # LG-145236. The switch itself measures 2-1/4 inches long and 3-1/4 inches wide. The required mounting hardware is included. I have attached a short video demonstration on this product for you to check out.
view full answer... - Best Cost-Effective Solution for Broken Ultra-Fab Landing Gear LegThank you for reaching out! The UF17-841002 part number that you're seeing tells me you have the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 on your Keystone 5th wheel trailer and while I do have a solution to help you get some working landing gear, unfortunately there aren't replacement inner parts for this landing gear so you'll have to replace it. You can use the landing gear set I mentioned above or you can go with more of a cost-effective solution like the Lippert Manual...
view full answer... - Landing Gear Not Working on NUWA 2000 Snowbird 5th Wheel TrailerIf the landing gear is electrically operated and the motor makes noise but the legs do not move then it could just be that the battery does not have enough charge to run the landing gear. You can have the battery tested at an auto parts store. If the battery is fine and the motor makes no noise then you may just need to replace the switch. If you did raise the jacks too high then it could have damaged the threads on the screw and nut which would mean that you would need to replace the...
view full answer... - Replacement Landing Gear Extend/Retract Switch for Keystone Montana TrailerThe extend/retract switches for landing gear legs are more or less universal so I recommend the Replacement Switch for Stromberg Carlson Electric Landing Gear part # LG-145236. I am not sure why you have a total of six pins but this is sorta irreverent as a landing gear motor is only going to have two wires, power and ground. If the switch has any lights then that may then be why other pins are present but nonetheless you can still use the above and just wire it using the following diagram....
view full answer...
- Explanation of Landing Gear Switch Operation The Replacement Switch for Stromberg Carlson Electric Landing Gear # LG-145236 will be open and not moving in the middle position. The switch will close and complete the circuit to give you the extend or retract functions of the switch.
view full answer... - Replacement Motor For Stromberg Carlson Landing Gear 1A065012-02-01The replacement motor you need is the Replacement Motor for Stromberg Carlson Electric Landing Gear, part # LG-142178. The replacement gearbox needed for this motor is part # LG-179015. If you need a switch for this motor, you can use part # LG-145236.
view full answer... - Troubleshooting Landing Gear That Retracts But Does Not Extend ProperlySometimes landing gear will retract but not extend due to an issue with available trailer power. It takes more current to make the legs extend (when they are pushing against gravity) than when they are retracting, at which time the trailer's own weight helps to push the extended legs back in. You could have an issue as simple as a bad ground and/or loose power cables. This is easy to check and will cost you nothing. You can also do a bypass test on the switch to find out if the landing...
view full answer... - Is a Stromberg Motor Compatible with Ultra Fab Landing GearAs long as the mounting holes for the Stromberg motor are the same as what is on your Ultra Fab landing gear then it will fit. The Replacement Motor for Stromberg Carlson Electric Landing Gear, part # LG-142178, is a widely compatible motor and has a two bolt holes that have a distance of 4-1/8 inches center-on-center. You might also want to install the Replacement Switch, part # LG-145236, and use some Butt Connectors, part # DW05745-5, for your installation as well.
view full answer... - Are Wires Connected to Replacement Switch # LG-145236 with Spade TerminalsI went out to the warehouse and inspected a Replacement Switch # LG-145236. The wires on the back of the switch do indeed attach with spade connectors. But you have to remove the protective heat shrink covering around it to access the back of the switch.
view full answer... - Is the etrailer.com Landing Gear Set RVLG-8000 a Replacement Fit for a 1998 Sandpiper 5th WheelOur Landing Gear Set - 20-1/2" Travel - 8,000 lbs # RVLG-8000 has the weld stops in the standard dimensions where the inside measurement of the weld stops is 15-1/2 inches and the outside measurement is 17-1/2 inches (see attached picture). Since we do not have access to every trailer and RVs landing gear specs you will need to go measure where the weld stops are on your current landing gear. These should fit though since they use the standard weld stop locations. You have the option of...
view full answer...
- Replacement Landing Gear for a 1996 Sea Breeze 5th Wheel TrailerIf you take a look at the picture I have included you will see several measurements on a landing gear leg. If your existing landing gear jack legs match then it has the standard spacing so # RVLG-8000 with motor # LC142178 is a great option that won't break the bank. If you also need to replace the switch use # LG-145236. If your legs have different measurements let me know what they are and I can determine if there is a better option.
view full answer...
- Replacement Switch for Stromberg Carlson Landing Gear System on Trailer We do have a nice selection of replacement switches available for camper jacks and landing gear systems. If you have a Stromberg Carlson Electric Landing Gear System like what the Replacement Motor # LG-142178 you were looking at is designed to work with, the you can use the Replacement Switch # LG-145236. This particular switch can also be used with most other landing gear sets from Atwood, Venture, and Lippert. The switch is only available with the wiring included. I have attached...
view full answer... - Replacement Switch For Electric Landing Gear on 5th Wheel TrailerThe Replacement Switch for Stromberg Carlson Electric Landing Gear # LG-145236 will work with Stromberg Carlson models LG-1, LG-2, LG-3, and LG-4 as well as most electric landing gear sets, including Atwood, Venture, and Lippert models. So this is likely the correct option as that covers the majority of the landing gear options for your 5th wheel. The reason that you only have 4 wires for the new switch is that the ground is done through the black wire that runs to the negative battery...
view full answer... - Landing Gear Replacement for 2007 Keystone Cougar 29BHSIf your brackets are 2" tall then you most likely have the standard weld stop measurements of 15-1/2" inside to inside (see attached photo). With this being the case I recommend going with the Landing Gear Set # RVLG-8000 which has a weight rating of 8,000 lbs and offers 20-1/2" of travel. Since you have an older trailer I bet the weld stops have just been wedged in the mounting brackets which is why you are having a hard time finding them. This set comes with the gearbox and you can either...
view full answer...
- Troubleshooting a Venture Landing Gear Not Retracting If you can hear the motor moving when you hit the switch then it's probably the gear box. To replace it you would want the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies item # LC276602. You will also want to check your switch. If you can't hear the motor you can use a 12V battery to get power to the wire that signals the gear to extend. If it does extend with the 12V battery, the issue is the switch and the replacement you'd need is item # LG-145236.
view full answer... - Is There a Replacement Landing Gear Switch Available Without the Wiring PigtailAll of the replacement landing gear switches that we carry include the switch and the wiring pig tail. The correct switch will depend on what landing gear you have on your 2006 Ragen 3405. The Replacement Switch for Stromberg Carlson Electric Landing Gear # LG-145236 you were looking at is designed for use with Stromberg Carlson models LG-1, LG-2, LG-3, and LG-4 and can also be used with most electric landing gear sets, including Atwood, Venture, and Lippert models. If you have something...
view full answer... - How to Run Wiring for Replacement Landing Gear SwitchIf you are using either the Lippert Components Landing Gear Switch # LC145236 or the Stromberg Carlson Landing Gear Switch # LG-145236 you will connect the red wire without the fuse along with the longer black wire to the red and black wires on your motor. The short black wire will be run to the battery's negative post and grounded and the pink or red wire with the fuse will be connected to the battery's positive post.
view full answer...
- Needed Landing Gear Capacity for 5th Wheel Toy Hauler w/ 11,000 GVWRThe # RVLG-8000 would be a great choice. Since the axles will be supporting a good percentage of the weight when the landing gear are being used, a set of landing gear with a 8,000 lb capacity would be perfect. This supports more than half the maximum amount of weight the trailer will ever hold, so you'll have plenty of capacity plus some in reserve. Having more capacity than needed means that the landing gear won't need to work as hard and therefore you should get more life out of them....
view full answer... - Recommendation for Replacing Bevel Gears for Atwood Landing Gear or Replacing Entire Landing GearSince Atwood is no longer in the landing gear making business and you have an older 5th wheel trailer I recommend just replacing your entire landing gear set. This not only gives you peace of mind that everything is in good shape but it also makes tracking down replacement/repair parts in the future much easier. For your application I recommend the Landing Gear Set # RVLG-8000 which has up to a 36-1/2" lift and is rated for 8,000 lbs. This cost-effective option comes with the landing gear...
view full answer...
- How to Wire Replacement Landing Gear Switch Do you know who the manufacturer of the landing gear is? That would be the only way to know for sure if a switch will work so the best option is going to be the Replacement Switch # LG-145236 which is designed for Stromberg Carlson landing gear but will work with most electric landing gear sets, such as Lippert, Venture and Atwood. Wiring this is pretty straightforward and I have included a diagram showing you how it is done (the switch also comes with written instructions). You only need...
view full answer...
- Landing Gear Switch Installation and Wiring DiagramThe Replacement Switch for Stromberg Carlson Electric Landing Gear # LG-145236 has the wiring colors you specified and will connect in the manner shown in the attached photo. The pink will connect to the positive battery terminal. The short black will attach to the negative battery terminal. The long black will connect to one side of the motor and the red to the other side of the motor. These wires will change the direction the motor turns, so you will want to make sure they are connected...
view full answer...
- Landing Gear Legs Will Not Retract But Will ExtendYes, the issue that you are having with your landing gear set is most likely the switch. Luckily, these are pretty universal so you can use the Replacement Switch for Electric Landing Gear part # LG-145236 to replace this without issue. Please make sure to check the spade terminals at the back of the switch first to make sure one has not wiggled its way out.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Sarah H
Installed by:
Jeff D
Updated by:
Shelly K
Updated by:
Hannah L
Updated by:
Mike S
Updated by:
Matthew E
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jimmie D.
3/11/2024
Product is still working well with no issues.