Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
(168 reviews)
Price: $696.96
In Stock
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
Item # LG-3
Retail:$906.01
Our Price: $696.96
You Save: $209.05
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (168)
- Q & A (0)
- Photos
Stromberg Carlson Camper Jacks - LG-3
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Electric Jack
- Landing Gear
- 6001 - 7000 lbs
- 2 Jacks
- 35 Inch Lift
- Stromberg Carlson
- Weld-On
- Steel
Electric, fifth-wheel landing gear set's motor has an IP-rated switch for fast, easy, and safe operation. Each leg is 29-1/2" tall, offers 19-7/8" of travel, and has a 15" drop leg for extra lift. Combined weight capacity is 6.5K.
Features:
- Perfect for raising, leveling, and supporting your 5th-wheel trailer or RV
- Electric-powered adjustment for easy operation
- Direct drive reduces strain on your jack and allows landing gear to lift with ease
- No clutch that could slip
- Single-speed motor won't trip circuits or cause problems with coach's electrical systems
- IP-rated switch will not spark, so it can be mounted safely in bottle-gas area
- Drop legs minimize jacking time and help to level the trailer on uneven ground
- Legs adjust in 1" increments
- Cage pins included to release drop legs
- Upgrade to spring-loaded pull pins (LG-119113 - sold separately) for simpler drop leg release
- Hand crank included for manual operation
- Heavy-duty steel construction
- Gearbox is housed in a corrosion-resistant aluminum body
- Landing gear welds onto trailer frame
- Set includes 2 jacks, gearbox, motor, switch, footplates, cross shaft, hand crank, and hardware
- Made in the USA
Specs:
- Leg length: 29-1/2"
- Total lift: 34-7/8"
- Travel: 19-7/8"
- Drop leg: 15"
- Rate of travel: 5-1/2" per minute
- Combined weight capacity: 6,500 lbs
- Cross shaft length: 41" - 71"
- Footplate dimensions: 8" long x 5" wide x 2" tall
- Outer tube width: 2-1/2"
- 1-Year warranty
Note: Landing gear is designed to stabilize a portion of your trailer's weight, not to support the full GVWR of your trailer. Do not use landing gear to lift your trailer or RV during tire changes or service work because doing so will exceed the capacity of the landing legs.
Stromberg Carlson's landing gear was designed with safety in mind. The motor, manufactured by Lippert, won't trip circuits or cause problems with the coach's electrical systems. In addition, the IP-rated switch will not spark, so it can be mounted safely in the bottle-gas area.
Convenience is also a hallmark of this product. An inner drop leg on each jack makes leveling easy by allowing the jack feet to reach the ground quickly and at varying heights, saving time and thus reducing the draw on the trailer's battery. The cage pins that secure the drop legs can be replaced with spring-loaded pull pins (LG-119113 - sold separately) that allow for single-handed operation. Large, rectangular, pivoting footpads are included, but you can use larger, 9-inch-diameter pads (LG-210475 - sold separately) instead if you often camp on soft ground.
This system and its parts were designed to be compatible with most of the other fifth-wheel landing gear on the market, including Atwood and Lippert. If you're replacing your old landing gear, you can install this set from Stromberg Carlson using your existing mounting hardware.
LG-3 Stromberg Carlson Deluxe Electric Landing Gear for Fifth Wheel
Installation Details
California residents: click here
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
Customer Reviews
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs - LG-3
Average Customer Rating: 4.6 out of 5 stars (168 Customer Reviews)
Electric, fifth-wheel landing gear set's motor has an IP-rated switch for fast, easy, and safe operation. Each leg is 29-1/2" tall, offers 19-7/8" of travel, and has a 15" drop leg for extra lift. Combined weight capacity is 6.5K.by: Troy05/03/2024
Great jacks and great fit, however the motor already went out not sure why just quit.
by: Steve B.09/20/2017
Let me start by saying this review is about the product, not e-trailer. etrailer is great. I love doing business with them. Their prices beat anybody, and the free and FAST shipping is a bonus. Now to the review of the LG-3 landing gear. The pros of this product are they are a direct replacement for the Lippert system on my trailer. No cutting, drilling or welding. They fit in the original brackets. I installed them while camping in about 2 hours with simple hand tools. The cons are they are a direct replacement for the Lippert system on my trailer. They use the same weak motor, that struggles to lift my trailer. The kit was missing bolts and pins and I had to use my old hardware until I could get back to town to buy new hardware. I wanted to go with the Bulldog 10K system, but wanted something that work with my Lippert remote system. The original system failed. I suspect this one will too. Next time I will go with something heavy enough to do the job. Check out the before and after pics and the pic of what can happen when your jacks fail and you have to resort to using hydraulic jacks to lift your trailer. A $4000.00 repair that could have been much worse.
Steve B.
9/20/2018
So far these are working. I got the higher torque model, which operates at a lower speed. I dont necessarily like the slower speed, but hey, at least they go up and down and the trailer hasnt fallen on my truck again. I am still disappointed that this landing gear is supplied by the manufacturer. It is woefully inadequate. As a side note, it is impossible to raise these legs with the coat hanger they give you for a hand-crank. This thing is ridiculous. That is why I keep a set of bottle jacks on-hand just in case of emergencies, and hope I never have to use them again.
Rachael H.
9/24/2018
Thanks so much for the follow up. If you do need to use your bottle jacks in an emergency situation, we do recommend to chock your trailer wheels and minimize all trailer movement as much as possible since bottle jacks are less stable than your primary landing gear.
by: Jared 08/17/2023
i had ordered the Stromberg Carlson landing gear to replace the broken set on my 5th wheel. When the package arrived the box was pretty rough and the motor was not in the package. I emailed etrailer late on a Thursday night and they emailed right back and by Friday morning they had already shipped out a replacement. on the following Monday UPS picked up the original and dropped off the replacement package. What an easy company to work with and the customer service is top notch. As for the landing gear set it seams to be better built than what the RV manufacture originally installed. Quality is better and the legs them selves are heavier so i am sure they will do a better job and should last longer than the original set. Very happy with the purchase and using etrailer.
by: Vikki11/21/2023
Box was ripped open I inspected and all parts are there, only problem the cross bar is not long enough. I had to use the old rod.
by: Mike08/04/2023
Missing pieces. Not impressed at all.
Katrina D.
8/8/2023
That is not good at all! Lets get the missing parts sent out to you.
by: Rosa M.08/12/2017
We installed the landing gear for our Montana.... it was a perfect fit. We highly recommend you. Thank you
by: Charles M10/04/2021
The motor on my 2002 Carriage Cameo landing gear went bad. This motor is louder than the original one was but it is also faster than the original one. The legs are a couple of inches shorter but not hard to work with. I do most of my own work on my vehicles, so found them easy to install.
Charles M.
10/10/2022
They have worked flawlessly for the past year and Im very pleased with the purchase!
by: Lane J12/11/2020
With a few minor modifications, I mounted the landing gear on our 1998 5th wheel and all is well. Has worked flawlessly since. Thanks for the fast delivery and great service.
Lane J.
12/12/2021
Outstanding product. Installed easily and works flawlessly.
by: Andy C.07/01/2017
I have a 2008 Keystone Montana Mountaineer 345DBQ. My Lippert Landing gear had broken with age and wear causing my truck and fifth wheel had become one. I was desperate to get the landing gear fixed for a trip in 6 days. Sandy J assisted me on the phone on a SUNDAY afternoon and was able to have the parts on my doorstep by noon on the following Thursday. The installation took me less than two hours and the landing gear works perfectly. It is quiet and operates very smoothly. I recommend etrailer to my family and RVing friends. They saved my vacation!
by: Jeff10/19/2022
The jacks do not have grease serts and no way to keep the gears and drive lubricated. The motor is wired backwards so the legs operate opposite of what the buttons indicate.
by: Larry 07/29/2022
I would recommend to anyone who needs parts for their travel trailer.
Etrailer keeps you informed on the progress of your order and if you have any issues they resolve it asap.
Great place to do business with.
by: Eric 08/26/2021
This landing gear was perfect for my trailer. They are really strong and can lift just about anything. I will say though, they are very slow. The electric motor isn't all that slow but doing it by hand takes a long time. But that's just a backup anyways.
by: Troy 10/13/2019
I replaced my landing gear with this unit a year ago. It fit perfectly on my 2007 37ft keystone challenger. Easy to install, took about two hours to complete. Not overly powerful motor but as good as original equipment. My trailer weighs 12000#. No issues so far.
by: Gary S06/13/2020
The landing gear that I bought from Etrailer was the exact one I needed. The lady that helped me did a great job. I was not sure of what I needed but she knew the correct parts and the correct size. I am very happy that I bought from this company.
by: Pamela11/13/2017
Received product as promised and in good condition. Installed it yesterday without too much fan fair. Working on any RV is always is treat. The only thing that didn't seem to fit was the cross rod, it was too short to go across our 5th wheel and ours isn't an over wide one. Just used the old rod and so far everything works fine. I didn't measure the width when we were ordered I concentrated on the length of the main tubes. All is good
by: Mike C08/24/2017
etrailer was extremely helpful finding a replacement for my RV 5th wheel landing gear. I have a '08 Cardinal 3100RK and the RF landing gear failed. The LG-3 was a drop-in replacement so I did not have to use the weld-on frame brackets that come with the package. I had to do a little grinding on the "follow" leg but otherwise it was a simple installation.
by: Allen G08/05/2016
I replaced both landing gear, motor and gear box on my fifth wheel. I was able to install all of it within a few hours with very little assistance. Mandy was very helpful from choosing the right set to keeping me informed on the shipment. I will definitely purchase all my trailer parts from etrailer in the future.
by: Mike C.05/01/2019
Received in a timely manner. Exact fit. The original landing gear on out fifth wheel had gotten very weak and would stall out during the lifting process. The LG-3 lifts our 33 footer with ease.
by: Steven Smith04/24/2020
They work good a little under powerd compared to the original ones if I run them for more then 10 seconds lifting the trailer the fuse burns not sure why but they get the job done
by: Leroy 10/25/2019
Fast, free shipping, three days from order to porch. Installed easily was almost a direct replacement for the manual landing gear that was on the trailer. The 6500 pound motor is fast but not very quite. Beats hand cranking any day of the week.
by: John H.08/14/2018
The LG3 system was a direct replacement for my original Atwood system.spacing was correct but I needed to grind about .020 off the top of the existing bracket. The jacks then bolted in perfectly. However the wiring diagram is incorrect for the leads to the motor from the switch. Just reverse the polarity by switching the wires.
The instructions are vague.
by: Mark Z.08/17/2017
Delivered right on time. Installation was quick as these were an exact replacement part. Had 5th wheel back to normal in no time. Now I can drive my truck again! I would recommend etrailer to anyone with an RV. Great service..
by: Brian08/24/2017
Happy with the product so far. It was easy to install, the harness was complete for the motor. The only issue I had was the switch plate got cracked during shipping and the switch operated backwards from the label, but just have to switch wires around to motor to correct. Will see how reliable the motor is because the trailer gets used a lot.
by: Thomas E09/05/2021
This is not the first time I have ordered products from etrailer. Received this products within a week when ordered. Install the replacement jacks from the orginals work great. Thank you
by: Robert08/10/2018
This unit was installed to replace the identical unit that failed. It operates very smooth and does the job. The failed unit was completely dry of lubrication on the jack screw that is attached to the tube that telescopes up and down. Venture Manufacturing now lubricates these and suggests periodic lubrication.
25
168
Show More Reviews
See what our Experts say about this Stromberg Carlson Camper Jacks
- Replacement Landing Gear For 2004 Forest River Sierra 5th WheelIn order to pick out the direct replacement for your landing gear on the 2004 37 Ft Sierra toy hauler I would need to know the measurement between the mounting brackets. The most common measurement is 17-1/2" but if your landing gear brackets do not measure 17-1/2" you can remove the brackets and weld the new ones to the trailer. You also want to make sure the landing gear lift is not shorter than the landing gear you have now. The Stromberg Carlson Electric Landing Gear Set with 34-7/8"...
view full answer... - Comparing Stromberg Carlson Landing Gear Kits LG-1 and LG-3 For 2007 Cherokee Fifth WheelI would go with the # LG-3 as it has a higher capacity at 6,500 lbs which means it will move a bit quicker and have to work less hard which means it will last longer. The # LG-1 has a lower capacity at 5,500 lbs works great for a lot of people, but the # LG-3 is the better choice.
view full answer... - Can the Gears Inside an Atwood Landing Gear Set Be ReplacedI do have an option for you but Atwood has since gone out of business and there are no repair kits for their landing gear legs. Therefore, the only option you have would be to replace the entire set. For this, the Stromberg Carlson Electric Landing Gear Set part # LG-3 is a very popular option. It comes with new brackets if yours do not match the required 17-1/2" outside to outside and 15-1/2" inside to inside for the above.
view full answer... - How to Determine Correct Replacement Landing GearWhat I think you are saying is that you need new landing gear for a 1997 5th wheel and the currently installed set is 33-3/4" in length. To determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket as shown in the diagram. From there you will be able to choose the amount of lift and weight capacity that will work for you. For the length you...
view full answer...
- Repair Kits for Lead and Follow Jack Landing GearThank you for the photo but trailer manufacturers do not keep any type of database with specific part numbers that we can access; even if they did it would not be a guarantee that the parts would be the same on a trailer that was made 20 years ago. The only repair kits we have are designed to be used with specific Lippert or Stromberg Carlson landing gear so you can take a chance and see if one of them will work. For a lead leg repair kit there is the Lippert # LC146059 or Stromberg Carlson...
view full answer...
- Dimensions of Replacement Crank Handle # LG-119226The inner diameter of the Replacement Crank Handle # LG-119226 where it connects to the landing gear is 1/2" while the diameter of the outer sleeve on the landing gear end is 3/4". Please note that this is designed for use with Stromberg Carlson landing gear # LG-1, # LG-2, # LG-3, # LG-4, or # LG-183708. It can fit with a lot of other brands like Atwood or Lippert but if you don't have this landing gear just let me know what you have and I can see if we have one that is compatible with...
view full answer...
- Replacement Landing Gear with 29-1/2 Inch LegsYou have a few choices for replacement landing gear with legs that measure 29-1/2 inches, depending on what weight capacity you need and if you want manual or electric landing gear. - Stromberg Carlson # LG-1: Electric Landing Gear with 5,500 lb Capacity - Stromberg Carlson # LG-3: Electric Landing Gear with 6,500 lb Capacity - Stromberg Carlson # LG-183708: Manual Landing Gear with 8,000 lb Capacity Just make sure you measure the distance between the mounting brackets from outside to...
view full answer...
- Recommendation to Replace Landing Gear on 2006 Keystone Cougar 5th Wheel Trailer To replace the landing gear system on your 2006 Keystone Cougar I recommend taking a look at the Stromberg Carlson Electric Landing Gear Set # LG-3. This is a really nice system that features electric-powered adjustment for easy operation and heavy-duty steel construction that will hold up great over time. It has a combined weight capacity of 6,500 pounds. The outer tube of the landing gear legs measure 29-1/2 inches tall with weld stops that are spaced apart 15-1/2 inches inside to inside....
view full answer... - What Is The Travel Speed Of The Stromberg Carlson Electric Landing Gear # LG-3The Stromberg Carlson Electric Landing Gear Set # LG-3, will retract at a rate of 5.5 inches per minute. I called Stromberg Carlson and they were not able to tell me what the speed rate was when lifting the trailer. This rate is based on a trailer that does not exceed the 6,500 lb capacity.
view full answer... - Choosing the Correct Replacement Landing Gear for 2004 Montana 2955RLBoth sets of the Stromberg Carlson landing gear you referenced mount to brackets that are 17-1/2 inches apart, so if your brackets have the same measurements the landing gear will fit perfectly. According to my research, the 2004 Montana 2955RL has a dry hitch weight of 1,980 lbs, so # LG-1, with a capacity of 5,500 lbs, would be a great choice. I've added a link to a video review of this landing gear for you to take a look at.
view full answer... - Replacement Landing Gear with Motor to Replace # VMC940RB-209458Thank you for getting me the Venture part number from your current landing gear. Based on that we know the Stromberg Carlson landing gear set part # LG-3 will be an exact replacement and will give you an all new set of powered landing gear with a 6,500 lb capacity.
view full answer... - How to Determine Replacement Landing Gear for Keystone FuzionI can tell you exactly how to determine what replacement landing gear you need for your 2012 Keystone Fuzion FZ310, though we don't have any way of knowing what will work for any one specific trailer, which means you'll need to take some pretty simple measurements. Additionally, I recommend replacing the entire unit as opposed to just one side because this will ensure compatibility of all parts as well as weight capacities being equal. To determine the correct replacement landing gear,...
view full answer...
- Powered Landing Gear for 5th Wheel Trailer that Does Not Have Landing GearThe Stromberg Carlson Electric Landing Gear kit part # LG-3 comes with everything you'd need to add electric landing gear to your fifth wheel. It comes with brackets you'd weld to the trailer as well as the motor and gear box as well.
view full answer... - Replacement Landing Gear for 2014 Heartland GatewayYes, the Stromberg Carlson Landing Gear part # LG-3 that you referenced will fit your 2014 Heartland Gateway based on what you mentioned. What you have basically fits the majority of landing gear sets out there.
view full answer... - Replacement Drop Leg for 2017 Heartland 328RE SundanceIn order to get the correct replacement drop leg you will need to know the manufacturer and model of your current landing gear because they do need to match in order to keep your Heartland Sundance level. For example, the Replacement Lead Jack w/ Drop Leg # LG-179013 is designed for use with Stromberg Carlson models # LG-1, # LG-3, and # LG-183708. I've added a link to our page with out selection of landing gear for you to take a look at.
view full answer... - How to Determine Correct Replacement Landing GearTo determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket as shown in the diagram. From there you will be able to choose the amount of lift and weight capacity that will work for you. For example, the Stromberg Carlson Electric Landing Gear Set # LG-3 has standard dimensions of 17-1/2" from bracket to bracket, 34-7/8" of lift and a 6,500...
view full answer...
- How to Determine the Correct Replacement Landing Gear for a 2008 Forest River Wildwood 5th WheelGiven the description of your problems, combined with the age and lack of information available for your landing gear your best bet is going to be to replace the landing gear. To determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket as shown in the diagram. From there you will be able to choose the amount of lift and weight capacity...
view full answer...
- Recommendations For Complete Fifth Wheel Landing Gear For 2004 Jayco EagleI do have a couple of solutions for you that will work for your 2004 Jayco Eagle fifth wheel. Upon first glance, it appears that your landing gear might have been made by Venture, which is not one of our vendors, but we sell other systems that will work well. I recommend using the Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs # UF17-943010. This landing gear will allow you to adjust independently for easy and quick leveling. The leg will travel 1 inch every 15 seconds,...
view full answer...
- Replacement Landing Gear System for 2010 Palomino Sabre 31RETSBased on the weld stop measurement you listed and the GVWR of the 2010 Palomino Sabre 31RETS the Stromberg Carlson Electric Landing Gear Set # LG-3 will work really well. This system features a 6,500 pound weight capacity, provides a total lift of 34-7/8 inches, and weld stops that are spaced apart by 15-1/2 inches inside to inside (and 17-1/2 inches outside to outside) so you can use your existing brackets. A hand crank is included for manual operation if you lose power, and the direct...
view full answer... - New Gear Box Recommendation for Landing Gear on 2007 Keystone Challenger 34 RBHYou have a very common landing gear setup on your trailer. For a replacement gearbox the aluminum version part # LC276602 would be your best option as it will hold up better than the plastic one. For a new motor you'd want the part # LC142178. For a kit that includes everything you'd want the part # LG-3 and you'd be set.
view full answer...
- Determining if Replacement Stromberg Carlson Landing Gear Legs Will Fit 2008 Keystone ChallengerThe Replacement Lead Leg # LG-179013 and Follow Leg # LG-179014 referenced in your question are direct replacement legs for the Stromberg Carlson # LG-1, # LG-3, and # LG-183708 Landing Gear Systems. They can also be used with many systems from Atwood, Venture, and Lippert. I am not sure of the exact system you have installed on your Keystone Challenger, so your best bet is to take a few measurements to see if these replacement legs will fit with your existing brackets. They have a leg...
view full answer...
- Is Replacement 30-3/4" Landing Gear Lead Leg AvailableI do have a solution for you but I'm not seeing that we carry a replacement lead leg that measures 30-3/4" tall like what you are asking about. Since you want to make sure that your landing gear legs have the same gear ratio as well I recommend replacing both legs to ensure everything works properly. For your application I recommend using the Stromberg Carlson Electric Landing Gear Set # LG-3 which have the standard 15-1/2" or 17-1/2" weld stop measurements, a 6,500 lb weight rating,...
view full answer...
- Replacement Landing Gear for 1999 Fleetwood Avion WestportTo determine the correct replacement landing gear, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket. 17-1/2" is the standard measurement. The amount of lift you need is also important so you want to make sure the lift is not shorter than what you currently have. Assuming you find that your weld stop measurement is 17-1/2", it is likely you can use the Stromberg Carlson Electric Landing Gear Set # LG-3....
view full answer...
- Landing Gear Replacement Recommendation for 2011 Fuzion Toy HaulerI'd go with a powered set of landing gear for your toy hauler as that will make operating them much easier since you'd be just holding down a button instead of having to crank the jacks up and down. For that I'd recommend the Stromberg kit part # LG-3 as this kit has a faster speed motor and a higher weight capacity so it will raise and lower the trailer quicker than other options out there. This jack also fits the standard mounting bracket dimensions found on most 5th wheel trailer so...
view full answer...
Do you have a question about this Camper Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Video Edited:
Jacob T
Written by:
Laura H
Installed by:
Randy B
Updated by:
Shelly K
Updated by:
Wilson B
Updated by:
Jenny M
Updated by:
Mike S
Updated by:
Matthew E
Video by:
Zach D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
5/3/2024
Troy, I am sorry to hear that the motor has stopped working for. Have you checked the 12V power line to make sure that it is still receiving power? I would also check the ground to make sure it still has a good connection. If the motor does need to be replaced, we have it is part # LG-142178 on our site.