Landing Gear Not Working on NUWA 2000 Snowbird 5th Wheel Trailer
Question:
We cannot get our landing gear to work at all, we think we raised it too far. Model SE-102
asked by: Karina D
Expert Reply:
If the landing gear is electrically operated and the motor makes noise but the legs do not move then it could just be that the battery does not have enough charge to run the landing gear. You can have the battery tested at an auto parts store. If the battery is fine and the motor makes no noise then you may just need to replace the switch.
If you did raise the jacks too high then it could have damaged the threads on the screw and nut which would mean that you would need to replace the system with a new one such as # RVLG-8000. The handle for this system is # RVLG-HDL. Or you could add a motor using # LC142178 and a switch such as # LG-145236.
Products Referenced in This Question
Lippert Venture 5th Wheel RV Landing Gear Motor
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Lippert
more information >
Replacement Switch for Stromberg Carlson Electric Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Switches
- Stromberg Carlson
more information >
Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- etrailer
more information >
Product Page this Question was Asked From
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
- Video: Ultra-Fab Power Twin 2 Electric Stabilizer Review
- Video: Deka Wiring 10-2-1 Review
- Shop: Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Q&A: What Gauge Wire Is Required To Use When Installing Ultra-Fab Power Twin II Electric Stabilizer
- Q&A: How to Wire the Switches of the Ultra-Fab Power Twin II Electric Stabilizer
- Q&A: Difference Between # UF39-941705 And # UF39-941707 Ultra-Fab Stabilizer Jacks
- Article: My Trailer Hitch Doesn't Fit
- Shop: Brake Controller
- Q&A: Ultra-Fab Products Trailer Jack # UF39-941705 Recommendation/Install Location on a 2007 Dutchman
- Shop: Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs
- Shop: Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
- Search Results: uf39~941705
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC141893
- Video: Trailer Brake Controller Installation - 1999 Sterling L-Line
- Shop: Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor
- Shop: Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System
- Q&A: Can an Ultra-Fab Leveling Jack be Used to Change a Tire
- Q&A: Wiring of Switches on Ultra-Fab Power Twin II Electric Stabilizer
- Q&A: Wiring Diagram For Ultra-Fab Electric A-Frame Jack
- Search Results: 10 2 duplex wire
- Video: Deka Jacketed 10 Gauge Wire Installation
- Video: Hopkins Trailer Wiring Installation Kit Review
- Video: Buyers Products Circuit Breaker with Manual Push-to-Trip Reset Review
- Search Results: ultra~fab products
- Shop: Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer brake controller