Mighty Cord Trailer Connector Adapter - 4-Way Flat to 6-Way Round - 12" Long

See what our Experts say about this Mighty Cord Trailer Wiring

• Does 4-Way to 6-Way Adapter A10-6034VP Carry 12 Volt Charge Circuit
  The 4 way to 6 way part # A10-6034VP does carry the 12 volt power circuit you'd need to charge a battery. The center pin of the 6-way is the 12 volt circuit and would be carried on the black wire on the other end of the adapter.
  view full answer...
• How Does Non-Wishbone Style Trailer Connector Wire to Trailer that Had Wishbone 4-Way
  You'll need to take off of the white wires on your trailer wiring and run it to the single white wire of the new 4-way as well as all of the brown wires to brown wire of the new 4-way. That would be the proper way to run wishbone style circuits of a trailer to a non-wishbone style connector.
  view full answer...
• Replacing a 5-Way Trailer Connector that Has 10 Wires Ran to It
  There is a very easy solution for you! It does not have 10 wires but is exactly what we use anytime we change these out. The Hopkins 5-Way Flat Trailer Connector w/ LED Test Lights part # HM47913 can be spliced directly to your current wiring color for color. Basically use the Deka Heat Shrink Butt Connector part # DW05745-5 and splice the two white wires to the single white on the plug. Do this for the 4 remaining colors and you are set. Use a heat gun or other heat source to shrink down...
  view full answer...
• Determining Function of Truck Trailer Wiring Circuit that is Brown with White Stripe
  Brown with white stripe could be either a ground for the running light circuit or possible the taillight circuit for the left hand side of the trailer. You'd want to test with a circuit tester liker part # PTW2993 to verify if and when the circuit has voltage and go from there. If it has voltage when running lights are on then yes it would need to run to yellow wire with brown stripe.
  view full answer...
• Mounting Bracket for Tow Ready 4-Way to 6-Way Trailer Connector Adapter, 1998 Lincoln Continental
  There can be some bracket/connector compatibility issues if the two components are of different manufacturers. Some sockets will not physically fit inside of some brackets. For the Mighty Cord adapter # A10-6034VP you would use bracket # RM-910030-5, but you would not attach it directly to the trailer hitch. What you would do is use short bracket # 18140 or long bracket # C57202, attach it to the hitch and then attach bracket 118137. Drilling into the hitch will void its warranty and can...
  view full answer...
• How To Hook Up Trailer with Two Brown Wires to Vehicle with One Brown Wire
  There should be five wires on your trailer side connector, a white wire which is for a ground, the yellow/brown and green/brown are for the running lights, a green wire for the right turn/stop light, and a yellow wire for the left turn/stop light because you have a wishbone wiring harness like part # A35W42B. In order to attach these wires to the vehicle side connector you will need to attach both yellow/brown and green/brown wires to the brown wire, the yellow wires together, and the green...
  view full answer...
• How to Connect a 4-Way Vehicle Connection to 5-Way Trailer Connection
  It sounds like you have a 4-way connection on your vehicle and a 5-way connection on your trailer. You can plug the 4-way into the 5-way and the lights on your trailer will work as intended. The additional connection point on a 5-way is for the reverse lockout. If you do not need this you can cover it/cap it off, it does not have to be used. Alternatively you could add a 5-way adapter like the Curt # C57187 if you need the reverse lockout function. As far as the turn signal and brakes...
  view full answer...
• Wiring A 2008 Toyota Highlander for Towing a 1996 Flagstaff Cobra Camper with 6-Way Square Connector
  Jayco uses a different wiring code than most, so in all likelihood, it will not work. I would just cut off the 6-Way square, tape off the brake and battery wires, and connect the 4 wires to a new 4-Way flat connector like part # 9653P. A better solution may be to install a more common 6-Way Round trailer connector on the vehicle and trailer. You could use the Pollak 6-Pole, Round Pin, Trailer Wiring Connector, item # PK11604, on the trailer end and a 4 Pole to 6 Pole Adapter, item # A10-6034VP....
  view full answer...
• Trailer Clearance Lights Stopped Working After Replacing One Clearance Light
  This sounds like a ground issue or possibly faulty wiring. Trailer light grounds and wiring are much more exposed to the elements and trailer suspension is not as good as on a vehicle to it is more susceptible to problems like this. Make sure that the vehicle side and trailer side connectors are clean and free of corrosion inside and out. The main connector grounds should be attached to clean and corrosion free bare metal surfaces. The light grounds should also be attached to clean and...
  view full answer...
• What are the Trailer Wiring Color Codes for Standard 4-way Wiring
  Sounds like your trailer is using a wishbone style of 4-way connection that is running all of their ground (white wires), and running lights (brown wires), back to the 4-way connector. You could use a standard 4-way still but you would need to splice all of the ground and running lights together to wire them to something like the part # HM48110.
  view full answer...
  
• How to Connect a Jeep with 4-Way Flat Connector and a Winnebago with a 6-Way Round Connector
  If your Jeep has a 4-Way Round and your Winnebago has a 6-Way Round then you simply need an adapter like the Mighty Cord # A10-6034VP. This comes with loose wires for a ground, 12V Power, and a Brake Controller which you may need for your trailer. Cut off your 4-Way Round and the 4-Way flat on this adapter and then splice the wires together function for function. This will pass along your basic lighting functions so if your trailer is equipped with brakes or need 12V Power then you will...
  view full answer...
  
• Trailer Wiring Adapter to Go From Vehicle 4-Way Flat to 6- or 7-Way Trailer Connector
  For a trailer that has a 6-Way and a vehicle that has a 4-Way flat you will need a different kind of adapter. Double check the pins on the trailer side. If the connector does have 6 round pins then for an adapter you will need # A10-6034VP. Your 4-Way will plug into the 4-Way on the adapter and the white wire will need to be attached to the vehicle frame. This will provide lighting functions. If you also want the brakes and 12 volt circuit to work then I recommend # ETBC6 which is the...
  view full answer...
• Trailer Connector Adapter Needed to Convert 6-Way to 4-Pole
  The # A10-6034VP adapter you referenced is designed to convert an existing 4-pole connector on a vehicle for a 6-way for a trailer. The white wire needs to be grounded to the vehicle frame, and once the 4-pole on the adapter is plugged into the 4-pole on the vehicle. However, it sounds like you're wanting to convert the existing trailer connector on the vehicle to work with a 4-pole on the trailer by using and adapter like # PK12717. Before installing an adapter, you will want to ensure...
  view full answer...
• Wire Colors for a Jet Ski Trailer
  It sounds like you are trying to determine which wire has winch function on your trailer. If that is the case then the color is more or less irreverent as the trailer manufacturer could have used any color they want for the respective signals. Therefore, the only true way to determine function is to apply 12 volt power to each wire and see which light it illuminates. I will however say that the white wire is usually a ground and the brown wire is usually for the running lights.
  view full answer...
• After Replacing Trailer Side 4-Way Wishbone Harness with Non-Wishbone, Running Lights Dont Work
  The issue is likely in how the 2 brown wires are connected and then connected to the single brown from the new 4-Way. You basically need to make the 2 running light wires into one and then butt connect to the single brown. You could use the Quick Fix, # HMC20031, twist the two running light wires together and then put the newly combined wire in place. Or you could go ahead and swap the 4-Way for a wishbone, # A20WB. There also could have been a short that fried the lights when the original...
  view full answer...
• How to Connect a Bushtec Quantum II Trailer to a 2016 Mazda Miata
  To tow your motorcycle trailer with you 2016 Mazda Miata you will need both a hitch and a vehicle wiring harness. For the 2016 Miata, if you do not already have a hitch, them I recommend the Curt Trailer Hitch Receiver, # C11435.The hitch will install to your vehicle without any drilling or welding required. For a wiring harness, the Curt T-Connector Vehicle Wiring Harness With 4-Pole Flat Trailer Connector, # C56300 is confirmed to fit the 2016 Mazda Miata. The connector will plug into...
  view full answer...
• Wiring for Five Trailer Wires to 4-pin Connector on Tow Vehicle
  It would seem that your tow vehicle has a typical 4 wire connector where white is ground, green is the right turn signal, yellow is left turn signal and brown is running lights. In this configuration the brown wire from the car connects to the brown wire from the trailer. Also you tell us that your trailer has five wires which are connected to a flat 4-pole connector. It appears that you have a "Wishbone" configuration where two wires for the running lights are merged together for one...
  view full answer...
• Easiest Way to Install 6-Way Trailer Connector on 2011 Honda Ridgeline
  The easiest way to install 6-way wiring on your 2011 Honda Ridgeline will be to start with a 7-way that's custom fit for your vehicle like the Tekonsha part # 118253 and then use a 7-way to 6-way adapter # HM47570 to match the 6-way on your trailer.
  view full answer...
• Why Would Trailer Wiring 4-Way Have 5 Wires Ran to It
  Typically a 5th wire ran to a 4-way harness is either a wishboned running light circuit where each side of the trailer's running lights are ran to either wire or it's a case where there is two ground wires. Since you said none of the circuits are working that to me says it's a ground circuit that needs to be ran to the same circuit as the white wire. But you can test this by jumping a 12 volt circuit to the red wire and see what happens. If there's a spark as they touch it's ground. If...
  view full answer...
• Parts Needed to Connect 4-Way on Motorcycle to 6-Way on Trailer
  A typical 4-Way connector will have the ground on the white wire, tail/running lights on the brown wire, left turn/stop on the yellow wire, and right turn/stop on the green wire (see attached picture). If your trailer has brakes or a seperate circuit for the reverse lights then you would want to use an adapter like part # A10-6034VP on your motorcycle so that you can still utilize all of the functions on your trailer. I have attached a photo showing how this adapter should be connected...
  view full answer...
  
• Replacing 5-Way Trailer Connector that Has 9 Wires Ran to It
  That's the most wires I've seen ran to a 5-way connector! Looks like you have several white ground wires, a running light circuit that runs to each side with the brown/green and brown/yellow, left and right stop/turn circuits, and then two reverse light circuits for the red wire. For the combined circuits like the red wires, white, etc. you can run them all to a single wire on your new 5-way connector like the part # HM47910.
  view full answer...
• Adapting a 6-Way Square Jayco Trailer Connector to 7-Way on Vehicle
  The easiest thing to do would be to replace the 6-Way square on the Jayco trailer with a 7-Way, # PK12706. You can adapt the 6-Way Jayco to the 7-Way on your vehicle. But it will take a little bit of work. First, you will need 6-Pole Square Trailer Wiring Connector Kit # 37995 because the Jayco square plug doesn't fit any other 6-Way square. This part has both the vehicle end and the trailer end which will both be needed. Then you will need a trailer side 7-Way such as # PK12706. The...
  view full answer...
• Wiring New 4-Way to Old Connector that Used Two Wires Per Circuit
  The second option you mentioned is the one you'd want to go with. You'd want to just butt connect the two wires from your lift to each the individual wires of a standard 4-way like the # W787264.
  view full answer...
• Parts Needed For Towing a Boat Trailer With 6-Pin Connector Behind 2019 BMW 540i
  First you will need the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # SH93VR for your 2019 BMW 540i. This will include a 4-way flat for your tail light functions. If your boat/trailer has electric or electric over hydraulic brakes, you will be able to connect the 4-way to the Adapter # A10-6034VP. Combining this with the Wiring Kit # 5506 and Brake Controller # RED52VR will allow you to control the trailer brakes along with adding a charge line for the trailer. If your...
  view full answer...

Do you have a question about this Trailer Wiring?