Extreme Off-Road Swing-Up Trailer Jack Shipping Weight

Question

Question:

Would you please provide information about the shipping weight of this product? Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10 Lift - 1,650 lbs - Black

asked by: Luis L

0

Expert Reply:

The shipping weight of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black item # ORJW750BD is 44 lbs.

expert reply by: Jerred H

0

Answer 1

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 2

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 3

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 4

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

We do have potential options for you, but there are no bolt-on options that will be a direct fit for a 6" tall 3" wide frame. One option is to use the ARK Extreme Off-Road Swing-Up Trailer Jack #ORJW750BD. This jack is made to fit frames…

view full answer...

Answer 7

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

Answer 8

Yes, you can! So long as our Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel item #AM30820 is the same size and bolt pattern as what's on your Ironton trailer it can be used not only as a spare but also on your trailer with the…

view full answer...

Answer 9

I have included a dimensional drawing of the Dutton-Lainson Round Swivel Jack #DL22335 that shows the overall extended height of the jack at 40-5/8" tall. This measurement is from the bottom of the wheel to the top of the jack when extended.

view full answer...

Answer 10

The Lippert High-Speed Power Stabilizer Jack part #LC298707 would be an excellent replacement option for the now discontinued 337199 model. It does come with a new switch so you can either wire this up or reuse the existing, either way the switch…

view full answer...

Answer 11

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 12

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Extreme Off-Road Swing-Up Trailer Jack Shipping Weight

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching