Recommended Bolt On Jack w/ a Wheel for a 3 Inch x 2 Inch Trailer Coupler

Question

Question:

Hello - I have a trailer with a tongue that is 3 inches wide and 2 inches vertical. I am looking for a tongue jack with a wheel that will bolt on to this tongue. I wanted to ask if you could recommend a product. Thank you.

asked by: Seth H

0

Expert Reply:

We've got a couple of options for jacks with a wheel that will bolt to your 3" x 2" trailer tongue. Both have the ability to swivel up when you are towing your trailer. Which one you choose is going to depend on the terrain you store your trailer in. I have listed them below and included a couple of review videos so you can see them demonstrated:

Swivel Marine Trailer Jack with Caster Wheel - Bolt On - Sidewind - 10" Travel - 1,500 lbs item # DL67MR

Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift - 1,650 lbs - Black item # ORJW750BD

expert reply by: Jerred H

0

Answer 1

Fulton Snap-Ring Swivel Marine Jack with Fixed Length - 400 lbs Item #F1410050149 would require some modification to fit a 2 x 2 inch frame. It could be done but it would void the jack warranty. I recommend using trailer jack #FTJ120W0301. It comes…

view full answer...

Answer 2

You can use the Fulton Snap-Ring Swivel Jack #F1410050149 on a small enclosed trailer like the Haulmark Flex FL4X6DS0 as long as the tongue fits the jack mounting bracket which is made for 3 x 5-inch tongues. The Haulmark site does not include specs…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Recommended Bolt On Jack w/ a Wheel for a 3 Inch x 2 Inch Trailer Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching