Installing Extreme Off-Road Swing-Up Trailer Jack On Trailer With 3" Wide Tongue

Question

Question:

Hi. My trailer frame is 76 mm. The bolts that came with the jack are too short. What do I do now?

asked by: Gerald L

0

Expert Reply:

The Extreme Off-Road Swing-Up Trailer Jack # ORJW750BD is listed as fitting 2" wide trailer tongues, but I reached out to Ark and you can still use it with your trailer. The jack uses M8 high tensile bolts so you will just need to find some that are the correct length at your local hardware store in order to install the jack.

expert reply by: Robin H

0

Answer 1

When folded up and traveling the Xtreme Off-Road Ratcheting Trailer Jack item #ORJW750BD is 29" long from the top of the jack to the bottom of the wheels. From the bottom of the wheel to the center pivot point where the bracket attaches is…

view full answer...

Answer 2

To make sure the Ark Extreme Off-Road Swing-Up Trailer Jack #ORJW750BD will fit your trailer, there will be two things that need to be confirmed. First will be the tongue weight of the trailer you want to attach it to. This has a static, or resting,…

view full answer...

Answer 3

It sure does! If you take a look at the accompanying photo I added from an install we did, you can see the Ark Off-Road jack installed on a C-channel trailer frame. The correct part number for this jack is the following: - Extreme Off-Road Swing-Up…

view full answer...

Answer 4

When retracted the Xtreme Off-Road Ratcheting Trailer Jack item #ARK54FR is 29" long from the top of the jack to the bottom of the wheels. From the bottom of the wheel to the center pivot point where the bracket attaches is 14". When folded…

view full answer...

Answer 5

The Extreme Off-Road Swing-Up Trailer Jack part #ORJW750BD will fit any trailer with a tongue ranging from 3" to 6" tall. The width does not matter as longer bolts can always be used to accommodate different needs. That said, I don't…

view full answer...

Answer 6

The Titan Zinc-Plated, Leverlock Coupler #T4845000 measures 4-1/8 inches tall, so it looks like it may be too tall for your set up. If so, the only other 5,000 lb coupler for a 2" hitch ball that may work is one that has half of the height, the…

view full answer...

Answer 7

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 8

Yes, the Sleeve-Lock A-Frame Trailer Coupler #CA-5196-B that you referenced is a weld-on coupler designed to fit 50 degree A-frame trailers like you mentioned. Nearly all A-frame trailers are 50 degree so it's hard to find A-frame couplers that…

view full answer...

Answer 9

The Xtreme Off-Road Swing-Up Trailer Jack #ORJW350D has a maximum height of 21-1/2" from the center of the mounting plate on the jack to the bottom of the wheel. You will need to measure your trailer frame from the center of the frame to the…

view full answer...

Answer 10

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 11

Thank you for your email answering my questions on your axle. I have the information to help you with your tandem axle application. Your current axle is not a standard size, so I recommend replacing your current axle as well. There are two routes to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Installing Extreme Off-Road Swing-Up Trailer Jack On Trailer With 3" Wide Tongue

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching