Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2
(240 reviews)
Price: $672.00
In Stock
Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2
Item # CJ74
Our Price: $672.00
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (240)
- Q & A (0)
- Photos
- Used (1)
Brophy Camper Jacks - CJ74
- Truck Camper
- Stabilizer Jacks
- Sidewind Jack
- 3001 - 4000 lbs
- 2 Jacks
- 67 Inch Lift
- Brophy
- Steel
Easily load or unload your truck camper with this pair of sturdy cable jacks. Portable design does not require permanent installation. Simply place the lift brackets under your camper and crank to raise. Breaks down into 3 pieces for storage.
Features:
- Cable jacks help you load and unload your truck bed camper
- Portable design - no need to permanently install unsightly electric jacks on your camper
- Each jack disassembles into 3 pieces for easy storage
- Extra-tall poles let you clear the bed rails on tall pickups
- Hand winches let you easily raise and lower the jacks
- Safety latches keep the cables from free-spooling
- Plastic handle grips offer comfortable cranking
- Aircraft-grade cables are strong and reliable
- Sturdy tripod bases evenly distribute your camper's weight
- Help to eliminate front-to-back and side-to-side motion
- Large footplates help to prevent sinking and tilting
- L-shaped lift brackets support the bottom and the sides of your camper
- Simply place lift brackets under your camper and crank the winches to raise
- Durable, corrosion-resistant construction
- Tripod bases and lift brackets are black powder coated
- Upright poles are galvanized
- Made in the USA
Specs:
- Quantity: 2 cable jacks
- Lifting range: 17" - 67"
- Overall height when assembled: 76"
- Combined weight capacity: 3,000 lbs
- Lift bracket dimensions (each): 26-1/2" long x 2" wide x 2" tall
- Leg lengths:
- Fixed: 17-1/2" from end to edge of pole opening
- Collapsable: 15"
- Footpad diameter: 4-3/4"
- Winch gear ratio: 4:1
- 1-Year limited warranty
Note: Always use these jacks in pairs on level ground. Not approved for commercial or rental use.
Lifting your truck camper on and off of your pickup truck is challenging if you don't have the right equipment. This pair of reliable cable jacks helps you load and unload your camper with ease. No permanent installation is required, so you won't have unsightly and expensive electric jacks hanging off of your camper. And because these jacks break down into 3 portable, easy-to-assemble pieces, you can take them everywhere the road takes you.
Ideal for Tall Pickup Trucks
Got a super tall or lifted pickup? No problem. The uppermost poles on these jacks are elongated so you can lift your camper up to 67" off the ground, which should be more than enough to clear the bed rails of even the loftiest truck on the road.
Simple Operation
Using these jacks is simple. Place 1 jack on each side of your camper and position the L-shaped lift brackets underneath the body of the camper. Then crank the hand winches to lift or lower each side of the camper evenly until the proper height for loading or unloading is achieved.
It is recommended that 2 people operate the jacks simultaneously to make it easier to raise each side of the camper evenly. However, 1 person can do the job by alternately lifting or lowering each jack in small increments.
CJ74 C. R. Brophy Tripod Winch Jacks for Truck Campers and Camper Shells - 3,000 lbs - Qty 2
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
- Product did not meet expectations
Customer Reviews
Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 - CJ74
Average Customer Rating: 4.4 out of 5 stars (240 Customer Reviews)
Easily load or unload your truck camper with this pair of sturdy cable jacks. Portable design does not require permanent installation. Simply place the lift brackets under your camper and crank to raise. Breaks down into 3 pieces for storage.by: Melissa11/20/2022
Great directions for manual assembly, quality metal and parts. Solid and exactly the heavy duty I was looking for to use with my slide in truck camper.
by: John A03/01/2024
The Brophy jacks were strong, stable, easy to position, and easy to lift and lower my camper. it is a much better method than having four jacks to maneuver. And it cut down my time to 30 minutes total to load my camper instead of an hour and a half!
I have to start from my garage and winch my camper down on a cart to the street face because of the incline driveway is so dramatic and my camper won’t fit in my garage if it is attached to the truck.
I couldn’t be more happy they were great and now I have my truck loaded with my very modern camper and I’m enjoying quite the holiday! I’m using the 3 ton 67 inch trophy jacks and I’m lifting an 800 pound gross camper. The stability is outstanding.
by: William12/28/2023
The shipping box had parts partially showing. There were about 7 holes in the box.They parts were missing paint where they we exposed. However it was easy to assemble and works great.
Jenny N.
12/29/2023
Yuck, the box did not hold up. I will have our Customer Service team reach out to you.
by: Daniel12/13/2023
when using the jacks for the first time I couldn't get the truck under the camper because the legs are too close to the camper. The lip is only 2 inches. I called to see if I was dong something wrong and was refered to the manufacurer. I called them and they said the have never had the issue. Because I didn't want to return the jacks (they work great except not enough clearance) I decided to buy some 1/4 inch by 6 inch plate steel and bolted them to the bottom of the L to extend it an extra 4 inches on each side. Plenty of room now. Works fantastic.
by: Marcus 04/26/2024
Delivery was on. Time easy installation, all parts were complete. Lifts the camper perfectly, very satisfied
by: Bobby02/27/2024
Ours is a diy cowboy camper. 6.5'x 8'. Works well with a camper of this size.
by: David11/04/2023
Price was right and shipping was fast. When UPS delivered it there was a hole in the box and pieces were missing. I called and reached someone without being out on hold which surprised me. After explaining my situation, she had the parts shipped that day. Unbelievable customer service! I've ordered from Etrailer before but this is the first time I had an issue and it was handled fast and efficiently.
by: David11/10/2023
The package arrived and there was extensive damage to the product. Etrailer got right on it though and sent me a replacement within two days. That is one of the reasons I keep coming back to etrailer. Excellent customer service. Haven't got to use the lift yet.
by: Isaac03/17/2023
These do FREE WHEEL! The video posted by Brophy is incorrect, the jacks will free wheel when switched into down mode. This is false advertising.
Katrina B.
6/22/2023
We have gotten information from the manufacturer that on the jack the lever must be all the way forward or all the way back to be engaged. The person in the video did not fully engage the lever, thats why it did not make the same noise when they cranked the handle and allowed it to free fall.
by: Joseph R.02/05/2020
So I have owned my CJ7 4 Brophy camper Jacks for a year. Throughout this time, they have been outside exposed to the elements continuously, and they look and operate as if they were straight out of the box. I've been using the camper jacks to renovate my camper, and I couldn't have done this project without them. I am so happy I bought the camper Jacks it was the smartest purchase I've made in a long time, and etrailer.com was the best place to purchase them.
by: Roger03/07/2024
I like the camper Jack's but I will have to modify mine because when they are plumb they stand too close to my f250. The uprights slightly touch the truck if there is any movement of my camper. When the Jack's are properly in place my tires will run up and over the 3way foot support.
by: E Garlitz04/26/2021
Great Jack's that easily handle sled decks and toppers. Only complaint is you need to drill a hole and put a pin in base to keep it from falling off while moving around. I would buy these again.
by: Dennis 08/23/2023
Received on time, jacks are as advertised. Only complaint is one handle is broken due to abuse during shipping.
by: Tom 09/16/2022
well made much better than former cable jacks that we had from a previous camper. Very heavy duty CJ74 67" 3000lb lift We have a Ford F250 Superduty truck with higher side rails plus these jacks not only can lift higher but also can pick up camper from only 33" from ground which is an advantage. Very glad we bought
Brophy Camper Cable Jacks, PS: Also received with box intact all contents inside.
by: Brock09/22/2023
Shipping was quick, but a little more care could go into packaging this $600 set of jacks. The bases and painted surfaces are all scratched up from being thrown in a box together with no kind of protection from the other pieces in the box.
by: Gary 10/20/2023
Did the job. Directions did not say installer would need 3/4" wrench to turn crank so crank handle could be removed.
by: James 10/02/2023
Great product. Lifts my truck camper with ease.
by: Noah 02/01/2023
The jacks work as they should and had no problem lifting the camper out of the back of my lifted f250 they handled the extra hight no problem. The only problem I had was a weld had snapped on one of the support legs, but I emailed the customer service and got a reply the next day and after sending them a picture they shipped a brand new support to me at no charge. Great customer service and really easy to deal with.
by: Leslie S.11/11/2018
I sold and maintained R.V.'s for many years and had experience with the Brophy Jacks so I knew exactly what I was looking for when I ordered these. These jacks are easy and safe to use if instructions are followed. I have a small camper that had hydraulic jacks. These were always in the way when using my vehicle in the bush and in tight spots. Now I use the Brophy Jacks to load/unload my camper and then to load/unload the truck canopy. When working, we made a "Bed Rail" dolly. We could load a camper onto this dolly and move it anywhere on the lot that we wanted as the jacks will go close to the ground. A well made and useful product. I have a jacked up Tundra so the extra length is helpful. Thank you.
Leslie S.
11/15/2019
excellent as expected. no faults
by: Thomas11/07/2017
Finally got them setup and pulled the camper. They were delivered earlier than expected. They are well constructed and easy to use. etrailer promptly handled my concerns with some address issues . Jeri went above and beyond. I will use and recommend this company.
Thomas
11/7/2018
They performed excellently. I used them 4 times with no issues. Definitely getting my moneys worth. I should mention that one of the welds on on leg of one of the bases broke. Thankfully I was only putting them in garage.. I havent met any welders in our new town so cant use them anymore Its not very often a business cares enough to contact their customers. I am pleasantly surprised that you checked up. Regards,
by: Guy10/02/2018
Apppreciate the quick order process and delivery. The jacks worked like a champ.
Thank you.
by: Casey05/12/2023
Good product but packaging was horrible. Looked like it went through a hurricane. Was almost in two and was torn up in thin an cheap packing. Scratched up the product a good bit but they’re jacks and don’t need to be pretty but for the price I think better packaging is a must.
by: Jeremy06/12/2022
The jacks worked great but they could’ve been packaged better. half of one of the tags on the Jack was ripped off due to shipping and a bunch of the powder coating was chipped off the lifting assembly. the bottom of one of the pipes was Bent where it goes in the foot. It also took them about three weeks to ship when I ordered them it said they were in stock on my receipt after two weeks of waiting I called them and they said they didn’t even receive the Jacks yet
Jenny N.
6/15/2022
I dislike hearing that the jacks arrived damaged and I will definitely have our customer service team reach out to have this taken care of for you. We are working to ship our orders as quickly as possible during our busy summer season.
by: Bob H01/26/2023
Product is fine. The only problem was the sticky plastic film used to wrap the jack posts, impossible to remove easily, wound up scraping off with a utility knife.
by: Michael04/06/2021
I used these to lift a truck camper onto my 2018 Ram 2500. I initially tried using only one pair and found it to be extremely scary as the camper wobbled back and forth. I purchased another pair so I could have a jack at all four points. It's better, but still very scary to lift the camper with these. The camper will rock and swing as you jack it up from the torque of the jacking action.
If I could go back in time, I would have chosen to build electric jacks (at a higher cost) directly onto my camper instead of using these. They get the job done, but it doesn't feel safe.
25
240
Show More Reviews
See what our Experts say about this Brophy Camper Jacks
- Are the CJ74 and CJ74H the Same JacksThe Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 # CJ74 is the same jack as the # CJ74H only sold as a pair. There are no specs that are different between the two parts outside of the quantity.
view full answer... - What Comes with the Brophy Cable Camper JackYes, the Brophy Cable Camper Jack # CJ74 (2 jacks) or # CJ74H (single jack) does come with everything you need to jack your camper up out of your truck.
view full answer... - Light Duty Brophy Cable Camper Jack OptionsIf you're needing the 67" max lift then you can get two of the 1,500 lb version # CJ74H. Same Max Lift just half the weight capacity. If you do not really need up to 67 inches of lift, you can get the # CJ31 that will have a Max Lift of 57 inches and a capacity of 1,000 lbs. These are both great options that are more light duty than the 3,000 lb jacks # CJ74. I've included some videos for you to check out if you wanted to learn more!
view full answer... - Will the Brophy Cable Camper Jacks Work On A Camper That Does Not Extend Past Bed SidesThe Brophy Cable Camper Jacks part # CJ74 can be used for storage but if the side of the camper do not extend to or past the sides of the truck bed it would not be feasible for them to be used for loading/unloading. That said, you could somehow fabricate some extensions on the camper and or jacks but that's the only option I see.
view full answer... - Recommended Replacement Jacks for 2005 Lance 1191 Truck CamperI am not sure what model Atwood Jacks you currently have on your 2005 Lance 1191 Truck Camper, but I do have a replacement option that should work well. I recommend looking at the Brophy Cable Camper Jacks # CJ74. These have a combined weight capacity of 3,000 pounds but only require the use of 2 cable jacks. The lifting range on this system is 17 inches to 67 inches and they are operated by a hand winch. The price information will be listed on the product page. I have also attached...
view full answer... - Using CR Brophy CJ74 Camper Jacks to Lift Heavy Camper ShellAs long as the camper shell weighs less than the 3,000 lb capacity of the # CJ74 Camper jacks, you should only need one set. The lift bracket itself is 26-1/2 inches long, so be sure to place the brackets at the center of gravity of the camper shell so it'll be balanced once it's up on the jacks. If the camper shell is heavier, using 2 stes would be recommended.
view full answer... - Troubleshooting Rear Wheel Clearance Issue with Brophy Cable Camper JacksYou should be able to change the orientation of the Brophy Cable Camper Jacks # CJ74 so that the legs pointing towards the cab of your pickup and the other legs will sit under your pickup bed a little to help stabilize your camper. I have attached a picture to show what I am talking about. If you have the legs that point towards your tailgate clearing the tires then odds are you need to swap what sides they are on. If you did already try this let me know and I can help you further.
view full answer...
- What is the Height Range of the Brophy Cable Camper Jack Set CJ74The height range possible with the Brophy Cable Camper Jack Set # CJ74 tops out at 67-inches maximum down to a minimum of 17-inches, giving it a 50-inch operating range. The kit offers a 3000-lb total weight capacity and a 4-to-1 winch gear ratio. For safety always use the jacks on level ground.
view full answer... - What is Lowest Height Setting of Brophy Cable Camper Jacks # CJ74When the Brophy Cable Camper Jacks # CJ74 are cranked all the way down the bracket that holds the camper will be 17 inches from the ground. The bracket length is 26-1/2 inches long.
view full answer... - Recommended Replacement Jacks For Lance 815 Truck CamperI recommend looking at the Brophy Cable Camper Jacks Item # CJ74. These are universal jacks that are sold in pairs. They have a combined maximum weight capacity of 3,000 lbs and a lifting range from 17 inches to 67 inches. The Brophy jacks have an overall height when assembled of 76 inches and are operated by a hand winch. I have attached a link to additional information.
view full answer... - Can In-Bed Camper Jacks be Used to Lift Off Truck Camper ShellThe L-Bracket on the Brophy Cable Camper Jacks # CJ74 would need to slide under your camper shell on either side and then you would use the winches to help raise the camper shell off of your Ford F-350. You can use 2x4s if you want to but really the camper jacks can handle the weight so it really boils down to finding a way to stabilize your camper shell. Since these camper jacks were designed to be used for an in-bed truck camper I'm not sure if I have any pointers for your application...
view full answer... - Recommended Truck Camper Jacks With The Highest Lift I went ahead and took, and we actually don't have a camper jack system that will lift 8 feet high. The closest I was able to find is the: -Brophy Cable Camper Jacks # CJ74 which has a maximum lift of 67", as well as a combined weight capacity of 3,000-lbs. These jacks use aircraft grade cables, is made in the USA, and can be disassembled into 3 pieces for easy storage. I have attached a product review video for you to check out as well for you to check out.
view full answer... - Brophy Cable Camper Jacks For 1972 Cab Over CamperThe Brophy Cable Camper Jacks - QTY 2 # CJ74 should work fine for your 1972 cab over camper. As long as the combined weight does not exceed 3,000 lbs. The uppermost poles on these jacks are elongated so you can lift your camper up to 67" off the ground, which should be more than enough to clear the bed rails of even the loftiest truck on the road.
view full answer... - Truck Bed Camper Jack with More than 60 inche of LiftWe have the Brophy Cable Camper jacks part # CJ74 which have a max lift of 67 inches. It has a lift range of 17 to 67 inches and a 3,000 lb capacity.
view full answer... - Truck Bed Camper Shell Jack Recommendation We have manual truck bed camper jacks like the Brophy kit part # CJ74 which will work great, but we do not have any electric ones at this time. These have a combined weight capacity of 3,000 lbs and a lift range of 17 to 67 inches.
view full answer... - Recommended Truck Bed Camper Jack for 2011 Ram If you are looking for truck bed camper jacks for your 2011 Ram, I recommend looking at the Brophy Cable Camper Jacks # CJ74. These will allow you to easily load or unload your truck camper with just a pair of portable jack assemblies. They have a lifting range of 17 to 67 inches and a combined weight capacity of 3,000 pounds. The overall height when assembled is 76 inches. I have attached a link that will take you to our available selection of truck camper jacks that you can also look...
view full answer... - Will The Brophy Cable Camper Jacks Work With A Dually Truck?The Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 # CJ74 don't really stick out . They hold the camper pretty much flush with the edge of the camper. I went into our warehouse to measure for you and the 2x2 inch l bracket that holds the edge of your camper is 4-1/4 inches from the support pole. The outermost edge of that bracket is 6-1/2 inches from the pole. The issue you may face is that the tripod foot support is directly in line with that l bracket. It doesn't...
view full answer... - Replacement Jacks For A Lance 815 Truck Bed Camper I do have options available for you however, we only offer universal jacks sold in pairs not single replacement jacks for your Lance 815 truck bed camper. If the universal jacks are something you would like to consider, I recommend using the Brophy Cable Camper Jacks part # CJ74. The Brophy jack have a maximum weight capacity of 3,000 lbs. and can lift the camper from 17"-67". They stand 76" tall and are a non-permanent removable option.
view full answer... - Recommended Truck Bed Camper Jacks for a 1996 Northern Lite CamperThe only truck bed camper jacks we offer are the Brophy Cable Camper Jacks. As long as the loaded weight of your truck bed camper does not exceed 3,000 lbs then I recommend part # CJ41 for 57" of lift or part # CJ74 for 67" of lift. These jacks will do an excellent job of helping to load and unload your camper into the truck bed. They do not permanently install on the camper which makes for a very clean look and they can also be broken down into three pieces for easy storage.
view full answer... - 57 or 67 Inch Tall Brophey Camper Jack RecommendationIf it were me I would go with the taller 67 inch Brophy jacks part # CJ74. Having more height than needed would be better than not having quite enough. Plus your truck does sit taller than most similar sized trucks so the extra height would be beneficial.
view full answer... - Replacement for Older Happijac Truck Bed Camper JackThanks for the photo and that model of Happijac is nearing a quarter-century old as of this writing and there are no longer replacement parts available for it. The best option we can offer are new camper jacks, the Brophy Cable Camper Jacks and you will select the right one based on the weight capacity and maximum lift height you need. - 1,000 lbs: Brophy Cable Camper Jacks - 57" Max Lift Height # CJ31 - 1,500 lbs: Brophy Cable Camper Jack - 67" Max Lift Height # CJ74H - 3,000 lbs: Brophy...
view full answer...
- Are The Brophy Cable Camper Jacks StableYou should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back. You will need to use two jacks, one per side. You will just need to make sure your camper jacks maximum weight capacity exceeds the weight of your camper. I have included a the different model Brophy Cable Camping jacks and their weight limits...
view full answer... - Will the Brophy Replacement Poles 1108 Fit Their CJ31Jacks?With the Replacement Upright Pole # 1108 being a replacement for the Brophy Cable Camper Jacks # CJ74, it will have a 2 inch diameter. This will be larger than the 1-1/2 poles in your # CJ31 due to the additional height and weight capacity of this system. Unfortunately, Brophy does not offer a taller pole for the # CJ31 at this time. With that being said, if more height is needed, the only option we currently have will be to replace your current system with the # CJ74.
view full answer... - Diameter of Tripod Base for Brophy Cable Camper JacksI measured the inside diameter of the Replacement Tripod Base for Brophy Cable Camper Jacks # 1106 and found it was 2 inches. This base is a replacement for the Brophy Cable Camper Jacks - 57" Max Lift Height # CJ41 and 67" Max Lift Height # CJ74.
view full answer...
Do you have a question about this Camper Jack?
Used Items Available
Condition: Surface Scratches
Notes: Item has cosmetic scratches and some slight bends in the stands.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Edited by:
Lindsey S
Installed by:
Kathleen M
Installed by:
Randy B
Video Edited:
Dustin K
Written by:
Chelsea B
Updated by:
Wilson B
Updated by:
Noah M
Video by:
Zach D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Melissa A.
11/21/2023
The Camper stands I purchased a year ago have been fantastic! They are holding up very well in the multiple times Ive used them. Quality product! I recommend to others to purchase.. I do offer that these stands are best implemented with 2 people for accurate balance and lifting.. :