Recommended Truck Bed Camper Jack for 2011 Ram

Question

Question:

need to know the jack for a 2011 ram.

asked by: Arthur

0

Expert Reply:

If you are looking for truck bed camper jacks for your 2011 Ram, I recommend looking at the Brophy Cable Camper Jacks # CJ74. These will allow you to easily load or unload your truck camper with just a pair of portable jack assemblies. They have a lifting range of 17 to 67 inches and a combined weight capacity of 3,000 pounds. The overall height when assembled is 76 inches.

I have attached a link that will take you to our available selection of truck camper jacks that you can also look through.

expert reply by: Chris R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 6

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 7

Hey Chip, so we do have a set of Torklift camper tie downs that fit your 2024 Ford F-350 long bed with side steps and a factory hitch with the part number #TL87CR for the front set and part #TLF3008 for the rear set.

view full answer...

Answer 8

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 9

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you will…

view full answer...

Answer 12

I recommend installing the Air Lift LoadLifter 7500 XL Air Helper Springs #AL57541 which are confirmed to fit your 2024 GMC Sierra 3500 Denali Dually. I prefer these over others as they have an internal jounce spring which helps reduce bouncing when…

view full answer...

Recommended Truck Bed Camper Jack for 2011 Ram

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching