Diameter of Tripod Base for Brophy Cable Camper Jacks

Question

Question:

What diameter jack leg will the below tripod base accept Replacement Tripod Base for Brophy Cable Camper Jacks Item # 1106

asked by: Jack D

0

Expert Reply:

I measured the inside diameter of the Replacement Tripod Base for Brophy Cable Camper Jacks # 1106 and found it was 2 inches.

This base is a replacement for the Brophy Cable Camper Jacks - 57" Max Lift Height # CJ41 and 67" Max Lift Height # CJ74.

expert reply by: Kyle S

0

Answer 1

I spoke to my contact at Brophy and he informed me that the diameter of the pole that would fit the Replacement Tripod part #1003 that you referenced will be 1-1/2 inches.

view full answer...

Answer 2

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

view full answer...

Answer 3

The diameter of the pole that will fit into the Replacement Tripod Base for Brophy Cable Camper Jack - Qty 1 #1003, is 1-1/2 inches. So, it appears this will work for your application.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 7

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 8

Most slides have EPDM rubber roofs but because EPDM is rubber it requires treatment each year to keep it soft and prevent shrinkage. You could replace it with TPO which is another synthetic rubber that will last longer than the EPDM. The smallest…

view full answer...

Answer 9

Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part #344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a…

view full answer...

Answer 10

Yes you can absolutely use the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 with your TorkLift tie downs.

view full answer...

Answer 11

The Alpha Systems Superflex TPO RV Roof Membrane #AL25CV is 0.30" thick. This is the only thickness they offer currently for the TPO. You will need the Alpha Systems RV Roof Replacement Installation Kit #AL63FJ to install this roof…

view full answer...

Answer 12

Yes it will accept PVC adhesive, the felt backing will soak it up and help create a strong connection/bond. The adhesive has a longer life span than butyl tape and it is cleaner than using caulk or other sealants. It will need to be treated with…

view full answer...

Diameter of Tripod Base for Brophy Cable Camper Jacks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching