Light Duty Brophy Cable Camper Jack Options

Question

Question:

do you have a light duty version of this Item # CJ74 , I need the height but my shell is less than 200lbs

asked by: Ron M

0

Expert Reply:

If you're needing the 67" max lift then you can get two of the 1,500 lb version # CJ74H. Same Max Lift just half the weight capacity. If you do not really need up to 67 inches of lift, you can get the # CJ31 that will have a Max Lift of 57 inches and a capacity of 1,000 lbs. These are both great options that are more light duty than the 3,000 lb jacks # CJ74.

I've included some videos for you to check out if you wanted to learn more!

expert reply by: Adam E

0

Answer 1

We have the Brophy Cable Camper jacks part #CJ74 which have a max lift of 67 inches. It has a lift range of 17 to 67 inches and a 3,000 lb capacity.

view full answer...

Answer 2

The Brophy Cable Camper Jacks part #CJ74 can be used for storage but if the side of the camper do not extend to or past the sides of the truck bed it would not be feasible for them to be used for loading/unloading. That said, you could somehow…

view full answer...

Answer 3

You should be able to change the orientation of the Brophy Cable Camper Jacks #CJ74 so that the legs pointing towards the cab of your pickup and the other legs will sit under your pickup bed a little to help stabilize your camper. I have attached a…

view full answer...

Answer 4

Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 Item #CJ74 will work great with your 1,600 pound truck bed camper. Just make sure that the 67 inch maximum lift height is enough to get the camper into the truck bed. The…

view full answer...

Answer 5

As long as the camper shell weighs less than the 3,000 lb capacity of the #CJ74 Camper jacks, you should only need one set. The lift bracket itself is 26-1/2 inches long, so be sure to place the brackets at the center of gravity of the camper shell…

view full answer...

Answer 6

The Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 #CJ74 don't really stick out . They hold the camper pretty much flush with the edge of the camper. I went into our warehouse to measure for you and the 2x2 inch l…

view full answer...

Answer 7

If it were me I would go with the taller 67 inch Brophy jacks part #CJ74. Having more height than needed would be better than not having quite enough. Plus your truck does sit taller than most similar sized trucks so the extra height would be…

view full answer...

Answer 8

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

view full answer...

Answer 9

Yes, the Brophy Cable Camper Jack #CJ74 (2 jacks) or #CJ74H (single jack) does come with everything you need to jack your camper up out of your truck.

view full answer...

Answer 10

Brophy Camper Tie-Downs #HSWB do not have a weight rating since they do not support the camper's weight. The truck bed and frame handle that actual camper load and the tie downs provide stability to prevent the camper from shifting in the bed.

view full answer...

Answer 11

I spoke with my contact at Brophy and they stated you'll be fine using the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSWB as long as the railing on the back of your 2008 Chevy Silverado isn't over…

view full answer...

Answer 12

According to CR Brophy, the camper tie down brackets you'd looked at, part #HSWB are specifically designed to fit the bed of a 2019 Ford F-250 and 350. There does indeed need to be 2 inches of available space under the lip of the truck bed side…

view full answer...

Light Duty Brophy Cable Camper Jack Options

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching