Recommended Truck Bed Camper Jacks for a 1996 Northern Lite Camper

Question

Question:

I have a 1996 Northern LIte fiberglass cab-over camper. I have two bad jacks on the back. what can I use to replace them that is the least expensive?

asked by: Judy

0

Expert Reply:

The only truck bed camper jacks we offer are the Brophy Cable Camper Jacks. As long as the loaded weight of your truck bed camper does not exceed 3,000 lbs then I recommend part # CJ41 for 57" of lift or part # CJ74 for 67" of lift. These jacks will do an excellent job of helping to load and unload your camper into the truck bed. They do not permanently install on the camper which makes for a very clean look and they can also be broken down into three pieces for easy storage.

expert reply by: Conner L

0

Answer 1

You could technically tilt the Rhino-Rack Ski and Fishing Rod Carrier #RR572 to be vertical and install it on the rear or your ladder rack, consequently allowing your skis to be vertical. Alternatively, we do have the Malone Ski Storage Rack…

view full answer...

Answer 2

Each of the jack assemblies that comes with the Brophy Cable Camper Jacks #CJ41 weigh 43 lbs.

view full answer...

Answer 3

When the MaxxAir MaxxFan Deluxe #MA00-05301K is in the open position it sits above the roof 9-5/16" but when it is in the closed position it sits above the roof only 5". If you check out the linked review video our team member…

view full answer...

Answer 4

The overall height of the Timbren Spring Kit part #TGMRCK25D is 6-1/4 inches.

view full answer...

Answer 5

Yes, you will need a spacer. The Air Lift LoadLifter 5000 Air Helper Springs item #AL57341 are designed for the stock height on your 2024 GMC Sierra 2500. Which spacer you need is going to be determined by how big of a lift you actually have in the…

view full answer...

Answer 6

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box item #GY98GR weighs a hefty 120 lbs. This is the only way to add a gooseneck pin box to a 5th wheel trailer with a Rhino Box. You will also need the Safety Chain with 2 Hooks item #GY49GR. State laws…

view full answer...

Answer 7

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 8

You will actually be needing the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness #HM54FR for your 2021 Chevrolet Silverado 2500HD. This will ensure you have the correct wiring and length needed to install in your truck bedside. The…

view full answer...

Answer 9

Thanks for your patience. It took a few days to get the measurements for the Curt Trailer Hitch item #C96CR. I have linked a diagram I made below. The Curt item #C96CR is a class V hitch with a 2-1/2" receiver. It has a 20,000 lbs towing…

view full answer...

Answer 10

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 11

Lippert 1621 5th Wheel Pin Box - 15,500 lbs Item #LC1191191 weighs approximately 100 pounds including the wings the pin box bolts to. Lippert 1621 5th Wheel Pin Box - 21,000 lbs Item #LC1387882 weighs approximately 115 pounds including the wings the…

view full answer...

Answer 12

I do have an option for you but the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate part #VGD-10-4000 does not have a spot for the factory backup camera. Therefore you would either need to find a way to mount this yourself, go without, or…

view full answer...

Recommended Truck Bed Camper Jacks for a 1996 Northern Lite Camper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching