Will the Brophy Cable Camper Jacks Work On A Camper That Does Not Extend Past Bed Sides

Question

Question:

will the jacks work on a shell that dosnt extened over bed rails and can I drive out from under without hitting legs

asked by: Dougs

1

Helpful Expert Reply:

The Brophy Cable Camper Jacks part # CJ74 can be used for storage but if the side of the camper do not extend to or past the sides of the truck bed it would not be feasible for them to be used for loading/unloading. That said, you could somehow fabricate some extensions on the camper and or jacks but that's the only option I see.

expert reply by: Conner L

1

Answer 1

As long as the camper shell weighs less than the 3,000 lb capacity of the #CJ74 Camper jacks, you should only need one set. The lift bracket itself is 26-1/2 inches long, so be sure to place the brackets at the center of gravity of the camper shell…

view full answer...

Answer 2

If you're needing the 67" max lift then you can get two of the 1,500 lb version #CJ74H. Same Max Lift just half the weight capacity. If you do not really need up to 67 inches of lift, you can get the #CJ31 that will have a Max Lift of 57…

view full answer...

Answer 3

You should be able to change the orientation of the Brophy Cable Camper Jacks #CJ74 so that the legs pointing towards the cab of your pickup and the other legs will sit under your pickup bed a little to help stabilize your camper. I have attached a…

view full answer...

Answer 4

If it were me I would go with the taller 67 inch Brophy jacks part #CJ74. Having more height than needed would be better than not having quite enough. Plus your truck does sit taller than most similar sized trucks so the extra height would be…

view full answer...

Answer 5

The Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 #CJ74 don't really stick out . They hold the camper pretty much flush with the edge of the camper. I went into our warehouse to measure for you and the 2x2 inch l…

view full answer...

Answer 6

Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 Item #CJ74 will work great with your 1,600 pound truck bed camper. Just make sure that the 67 inch maximum lift height is enough to get the camper into the truck bed. The…

view full answer...

Answer 7

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

view full answer...

Answer 8

The height range possible with the Brophy Cable Camper Jack Set #CJ74 tops out at 67-inches maximum down to a minimum of 17-inches, giving it a 50-inch operating range. The kit offers a 3000-lb total weight capacity and a 4-to-1 winch gear ratio. For…

view full answer...

Answer 9

Yes, the Brophy Cable Camper Jack #CJ74 (2 jacks) or #CJ74H (single jack) does come with everything you need to jack your camper up out of your truck.

view full answer...

Answer 10

I spoke with my contact at Brophy and they stated you'll be fine using the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSWB as long as the railing on the back of your 2008 Chevy Silverado isn't over…

view full answer...

Answer 11

According to CR Brophy, the camper tie down brackets you'd looked at, part #HSWB are specifically designed to fit the bed of a 2019 Ford F-250 and 350. There does indeed need to be 2 inches of available space under the lip of the truck bed side…

view full answer...

Answer 12

Brophy Camper Tie-Downs #HSWB do not have a weight rating since they do not support the camper's weight. The truck bed and frame handle that actual camper load and the tie downs provide stability to prevent the camper from shifting in the bed.

view full answer...

Will the Brophy Cable Camper Jacks Work On A Camper That Does Not Extend Past Bed Sides

Product Page this Question was Asked From

Continue Researching