Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford
(109 reviews)
Price: $14.47
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford
Retail:$25.79
Our Price: $14.47
You Save: 44%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
- All Info
- Reviews (109)
- Q & A (0)
- Photos
Tekonsha Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Tekonsha
- Vehicle Specific
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.
Features:
- Wiring adapter eases installation of your electric brake controller
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
- Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
- Limited 1-year warranty
Installation of Tekonsha Brake Controller Adapter
This adapter plugs into the connector beneath your vehicle's dashboard. To reach the connector, remove the storage pocket that is built into the center of your dash, just above the ashtray. Once you have removed the pocket, you will see the gray, 4-pin connector that mates with the adaptor.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
306500 Tekonsha Brake Control Wiring Adapter with 2 Plugs
Replaces Tekonsha 3065-P
Item # 3065-P
Installation Details
This Product Fits The Following Vehicles
- 2005 - 2007 Ford F-250 Super Duty with factory 4-Flat
- 2005 - 2007 Ford F-250 Super Duty with factory 7-Way
- 2005 - 2007 Ford F-350 Super Duty with factory 4-Flat
- 2005 - 2007 Ford F-350 Super Duty with factory 7-Way
- 2005 - 2007 Ford F-350, 450, and 550 Cab and Chassis with factory 4-Flat
- 2005 - 2007 Ford F-350, 450, and 550 Cab and Chassis with factory 7-Way
California residents: click here
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Product did not meet expectations
- Alternate product found
Customer Reviews
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford - 3065-P
Average Customer Rating: 4.9 out of 5 stars (109 Customer Reviews)
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.by: Ethan 02/18/2024
Ford
Plug-in adapter was an exact match for the Ford wiring harness. Connecting to the new brake controller literally took seconds.
by: Ben B08/16/2017
2005 Ford F-250 Super Duty
Arrived on time. Install into 2005 f250 was simple using the plug in wiring harness I order with the Prodigy 3. I removed the in dash storage pocket and cut a hole in the back of the pocket to run the wiring harness, reinstalled pocket, installed bracket, plugged up controller. Looks great (see pic)
I have not pulled trailer yet but expect great performance. Thanks etrailer
by: Mike03/31/2017
Ford
I ordered the Tekonsha P3, and the Ford wiring harness to replace a failed factory trailer brake controller. Installation was less than 10 minutes. ETrailer is so on it, I received a call the day I ordered saying I had missed the shipping cut off for the day, I had paid for 2nd day, and she wanted to make sure I was ok with still going that route. Crazy good on the customer service. Thank you very much. Everything was as advertised. Video service on your website was a huge help as well.
by: Brent M.08/08/2016
Installed these on a 41' Landmark Key Largo and, holy cow, I can stop it now! Wish I'd had these in the mountains!. Product arrived intact but boxes were nearly destroyed. Need heavier packaging for the weight. But everything was present with no damage.
Installation was straight forward with no issues encountered. Take some time to plan your brake line installation to avoid future problems. I installed some square tubing across the frame to mount things to because there wasn't anything there. Nothing beneath the chloroplast in that area that would need servicing so it should work out well.
These were well worth the time and money. Just pull out in front of me now! (No please don't.)
by: Charles 11/10/2023
Perfect unit; saved a boatload of work.
by: Neil12/29/2022
The brake wiring has been in place for a year + and is working well. etrailer is always my first choice on anything related to my vehicles and trailers.
by: Bill - American Dock Mfg.03/28/2018
2005 Ford F-250 Super Duty
eTrailer provides superior advice as well as excellent pricing and delivery. Based on eTrailer's recommendation, we installed the Tekonsha P-3 Proportional Brake Controller (PN 90195) along with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford (PN 3065-P) on our 2005 F250 Super Duty to replace the OEM controller due to the OEM controller sending insufficient voltage to our 40ft., 26000lb., GVW FB trailer brakes. It took less than 20 minutes to install and works perfectly. It easily adjusts to advance or slow trailer braking and the inertial sensor on this unit works flawlessly. We are extremely happy with these products. Now if only we could permanently disable the TBC error warning light on the dashboard.
by: Heath06/26/2017
Chevrolet Colorado
Fast shipment and works great. Really makes a difference with the trailer slowing down and breaking on the mountain roads in Colorado.
Heath
7/9/2018
Great, still good.
by: Blaine06/05/2019
Ford F-350 Super Duty
I can not say enough about how great E trailer and James were to deal with. I had 2 brake controllers fail exactly 1 month after they were installed and this company stood behind their warranty and replaced them both. After the second failure I brought my F350 to my mechanic. He spoke to the tech experts at E trailer and discovered the problem may have been excessive ripple/noise in the output of my alternator. We replaced the alter and E trailer sent a third controller to my mechanic. It has worked flawlessly since that repair. These folks are the best at customer service, I can't express my appreciation enough. I will only use and recommend them in the future.
by: Kate11/24/2017
we Purchased an additional tow vehicle for our 5th wheel so we purchased another P3 brake controller from etrailer. Very simple product to install to your factory controller if it has one already. If not it takes a touch more effort to find the wires under the dash, but we love this controller and the ease of use and features it has
by: Scott B.06/14/2015
Received the Tekonsha P3 brake controller and wiring adaptor the other day. Installation couldn't be easier, a ten minute job thanks to the pictures on etrailer showing where to find the tow package plug on my truck. Great little unit with tons of features.. Shipping was extremely quick!
by: Anthony 10/19/2019
2007 Ford F-250 and F-350 Super Duty
My break controller was shipped fast and was easy to install (less than 5 minutes).
I haven't used it yet but will try it out in the next few weeks.
Tony
10/20/2020
Great product & worked better that the Factory builtin.
by: Chris H05/08/2014
Excellent customer service -quick turn around on order! The Brake controller and wiring harness were a great fit and easy to install... glad to finally be rid of the typical "TBC Fault" issues that plague the factory equipment! Thanks again E-Trailer!
by: Mike J05/18/2015
2010 Ford F-250 Super Duty
Plug and play installation made this incredibly simple. I went to 3 autoparts stores prior to ordering from etrailer, and nobody had anything that would fit the factory connection on my 2005 F250 superduty. Went online and found exactly what I needed. Shipping was quick, and had it installed about 10 mins after opening the package. Etrailer's videos are great.
by: Adam04/19/2018
2006 Ford F-250 and F-350 Super Duty
Plugged right in. Now my trailer brakes work. My truck is an xlt so, it didn't come with a factory trailer brake controller but, the harness was there.
by: Pete M.11/03/2017
Ford F-250 Super Duty
Great service Stacy A spent time explaining options, Pros and cons. Very friendly and knowledgeable. Product works great - F250 trailer brake controller Tekonsha P3 was a breeze to install. Better then factory!
by: John10/31/2017
2006 Ford F-250 and F-350 Super Duty
The wiring harness looked perfect and easily plugged into the Tekonsha brake controller and the vehicle. No issues at all. Great product quality once again!
by: Ray W06/15/2013
2005 Ford F-350 Super Duty
I have a 2005 F-350, replaced OME brake controller with a Prodigy P 3 [90195] and wire adapter 3065-P. It plug right in the truck's 7 way wiring works great.
Ray
by: Shawn T07/18/2017
2006 Ford F-250 Super Duty
Well designed, great length, simply plug and play. Once I had access to the brake controller plug in my 2006 f250, this adapter plugged right into it. I plugged the other end into my new brake controller and it was running.
by: Joe 11/18/2019
Works a described. Plugged right in to our motor home then into the brake controller box.
by: Jackson11/28/2014
This is a snap I cant believe it only took me less than 5 minutes to install. The website has the location of the harness on the truck so easy. I also was going camping and needed a rush order E Trailer exceeded my expectations
by: Leon 05/18/2023
Always helpful people and great support!
by: Timothy04/20/2019
I really appreciate Etrailer acting so fast in getting my package to me after the Post Office lost the last package. Etrailer is doing a great job with there costumer service.
by: Gary08/16/2019
Quick delivery got my trailer brake module 5535 draw-tite I command and harness took me about 15 minutes to install will be using it in a few weeks don't see any reason why I won't be satisfied with it
by: Ray-NM6R10/10/2019
This brake controller works and looks great. I comes with presets or you can fine tune the control.
25
109
Show More Reviews
See what our Experts say about this Tekonsha Accessories and Parts
- Brake Controller Solution to Allow 2006 Ford F-250 Tow Trailer With Electric Over Hydraulic BrakesThe # HBA-CAM wasn't designed for use with a Dexter electric over hydraulic actuator which is why you are still having issues. The only solution we can offer is a new brake controller that is compatible with electric over hydraulic actuators like the P3 part # 90195 which will solve your problems. All you need to install the controller is the correct install harness # 3065-P and you'd be set.
view full answer... - Bully Digital Brake Controller TC-301 Shows E3 ErrorAccording to the owner's manual for the Bully Digital Brake Controller TC-301, if there is a red light flashing and the display shows an E3 code then that means there is no trailer connected. Therefore, since you don't have a trailer connected I would not worry. However, if it still does this with a trailer connected then you will need to check your connection to the yellow wire. It should not drain your battery flashing E3. If you wanted to test the brake controller to see if there was...
view full answer... - Prodigy P3 Brake Controller Not Working on a 2007 Ford F-250 with Factory Integrated ControllerYou will need to have the TBC turned off by a Ford technician at a Ford dealer. Using the IDS, the Ford Technician should access the Programmable Parameters and then select the Personality/Dynamics. Select the TBC and turn it off. The fault code will now be removed and you can then install an after market controller. Also, make sure you are plugging the # 3065-P harness into the correct location. There are a couple of connectors that look the same.
view full answer...
- Trailer Brake Controller and Wiring for a 2006 Ford F-450 6.0 DieselTrailer brake controller wiring harness # 3065-P is the correct harness for your 2006 Ford F-450. In your picture, it would plug into the larger one on the right. The larger square end of the harness plugs into your truck's connector and the small flat end plugs into the back of the brake controller # 90195.
view full answer...
- Recommended Vehicle Wiring for Trailer Connection On 2005 Ford F-250For your 2005 Ford F-250, I recommend the 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End # HM40975 if you have a factory 7-way or factory 4-way. If you prefer the look of the # 118243 which is not a confirmed fit, I recommend the Replacement Multi-Tow 7-Way & 4 Pole Trailer Connector # 74682. If you truck does not have the factory 7-way wiring, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56032. Then to get 7-way...
view full answer... - Location Of Brake Controller Port On a 2005 Ford F-350If you have a factory 7-way at the rear of your 2005 Ford F-350, the plug will be behind the black pocket in the center of the dash, just below the radio. The plug will be the one on the right with the matching colors for the brake controller plug, including Red, Black, White, and Blue. I have linked an FAQ showing the location of the port on 2005 Ford F-250 and F-350 with factory 7-way. Also linked are instructions for the Tekonsha Wire Replacement, part # 3065-P.
view full answer... - Parts Needed to Install the Tekonsha Prodigy P3 # 90195 on a 2006 Ford F-350If your 2006 Ford F-350 has a factory 7-Way connector at the rear then you would need the adapter # 3065-P to install the Prodigy P3 # 90195 brake controller. If your F-350 has the factory 4-Way connector then you would use the same adapter for the P3 but you would also need to install the Adapter # 37185 and then use soe additional wiring like part # 10-2-1 to connect the 7-Way socket to the tow package wiring on the rear frame rail. I have attached an installation video as well as...
view full answer...
- Will the Ford Integrated Brake Controller on 2006 F-350 Work with Electric-Over-Hydraulic BrakesAccording to the owners manual of the 2006 Ford F-350, the factory integrated brake controller has not been confirmed to work with electric-over-hydraulic brake actuators. The Carlisle Control Adapter Module, # HBA-CAM, will solve your problem as long as you have a Generation 6 or newer HydraStar actuator with the following serial numbers HBA-10 serial number 313800 or higher HBA-12 serial number 705700 or higher HBA-16 serial number 506100 or higher If you have an older HydraStar actuator...
view full answer... - Brake Controller Connector Location on a 2007 Ford F-550The brake controller adapter, like part # 3065-P for a Tekonsha brake controller like the P2 # 90885, installs at the connector which is located behind the storage pocket that is built into your center dash right above the ashtray (see attached photos). I have attached the installation details for this adapter which will apply to matter what brand brake controller you have. Please note that in some cases you may need to run additional wiring # 37185 to complete the brake controller circuit....
view full answer...
- Brake Controller Compatibility With Electric Over Hydraulic Actuators And 2006 Ford F-350The Titan Disc Brake Kit and BrakeRite Electric-Hydraulic Actuator - Tandem, 3,500-lb Axle # T4843800 is an excellent system that works seamlessly together. The 2006 Ford F-350 Superduty DRW does fall into the category where Ford's factory integrated controller does not work consistantly. I've atttached the technical bullitin that goes along with this issue. The solution is to simply use an aftermarket brake controller and have your local Ford dealer turn off the TBC. This will remove...
view full answer... - Brake Controller and Trailer Wiring Adapter for a 2010 Ford F150The Tekonsha # 22292 is a plug in wiring adapter that will work with your 2010 Ford F-150, if your truck already has a 4-pole or a 7-way wiring system that can be be used with a brake controller. If your truck currently has a factory installed 7-way then you can plug the # 22292 wiring adapter into the wiring harness located in the dash of your truck and then, after routing the other end of the wiring adapter under the dash, you can plug it into the brake controller. If your truck does...
view full answer... - Replacement Trailer Brake Controller for 2006 Ford F-350It sounds like the internal inertia sensor is not working correctly. Hitting the gas pedal should definitely not cause a fault with a trailer brake controller that is functioning correctly. For your 2006 Ford F-350 I recommend the Tekonsha Primus IQ # TK90160 along with the wiring harness # 3065-P. If you don't want to add another controller to your cab, you can instead use the Curt Echo Wireless Trailer Brake Controller - 1 to 2 Axles - Proportional # C51180. This utilizes a mobile...
view full answer... - Location Of Brake Controller Plug On 2005 Ford F-350The brake controller plug is behind the access panel in the center of the dash on the passenger side. You would just unplug the harness from the old brake controller and connect the new brake controller wiring harness, to the mating connector that was connected to the factory brake controller. After this is done you can route the wiring to the mounting location you want and install the new brake controller. When you remove your factory brake controller you will get a fault code on the...
view full answer... - Does a 2006 Ford F-350 Only Need the Install Harness 3065-P to Install Prodigy P3The P3 brake controller part # 90195 and the install harness part # 3065-P will be all that you will need to install and use the brake controller in your 2006 Ford F-350. The other harness would not be needed and would be unnecessary for the function of the P3.
view full answer... - 3065-P Brake Controller Wiring Adapter Needed to Install Tekonsha P3 in 2005 Ford F350To install your P3 brake controller on your 2005 Ford F350, you'd need the # 3065-P brake controller wiring adapter. One end of the connector would plug into the rear of the controller, the other would plug into the connector under the dash. For a 2005 model, the connector is located behind the storage cubby right above the ashtray. Pull the storage pocket out from the dash, and the connector will be clipped to the rear of the pocket, as shown in the photo I've provided for you.
view full answer...
- Does 2007 Ford F-250 Need to Be Flashed to Replace OEM Brake Controller with AftermarketYes, you will need to have your 2007 Ford F-250 flashed at a Ford dealership to install the Prodigy P3 and corresponding plug and play adapter: - Prodigy P3 # 90195 - Plug and Play Adapter # 3065-P We've had some people ask about disconnecting the battery for a bit and while this is worth a shot, it's likely not going to resolve the issue so you'll need to take the truck in to a dealer.
view full answer... - Brake Controller Install Harness Recommendation for a 2009 Ford F-53 Chassis MotorhomeFor the 1999-2011 F-53 chassis motorhomes there is a brake controller installation port behind the instrument cluster. We have heard it is fairly difficult to locate, but if you keep digging you should find a grey connector that would work. The correct harness needed to install the P3 brake controller # 90885 would be the part # 3035-P. For more info on this search the internet for the Ford document q-206.
view full answer... - Trailer Brakes Only Working with Manual Override on Tekonsha Prodigy P3 Brake ControllerThere are a couple possible reasons as to why the trailer brakes are only working when applying the manual override on the Tekonsha Prodigy P3 # 90195 and not when stepping on the brake pedal. The first possible cause is the easiest to rule out and is not actually a problem at all. The Prodigy P3 brake controller is a proportional unit. This means that it uses an integrated accelerometer that sends power back to the brakes in proportion to how hard the vehicle is coming to a stop. If...
view full answer... - Where Does Brake Controller Plug In on 2008 Southwind 36D Built on Ford F-550 ChassisI attached a picture that shows where the brake controller install harness part # 3065-P plugs in on an RV like your 2008 Southwind 36D that is built on a Ford F-550 chassis. For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate...
view full answer...
- Can Tekonsha Prodigy P3 # 90195 be Used to Replace Factory Brake Controller in 2005 Ford F-250Yes, you can replace the factory installed brake controller in your 2005 Ford F-250 SD with the Tekonsha Prodigy P3 Trailer Brake Controller, # 90195, and Plug-In Wiring Adapter, # 3065-P. You will just need to unplug the factory controller and use the new wiring adapter to plug in the P3. This will set a fault code on the instrument cluster. In order to have this removed you will need to make a trip to your local Ford dealer to have the PCM (Powertrain Control Module) turned off. Once...
view full answer... - Where Does a Brake Controller Plug Into on a 2004 Holiday Rambler on a Ford F-53 ChassisI believe you are talking about the F-53 chassis. There is a brake controller plug on those chassis. On a 2004 model it is located up under the dash, behind the instrument cluster. Take a look at the picture I have included showing this. For a brake controller I recommend the P2 # 90885 because it is easy to set up and use and it is reliable. The brake controller harness you would need for this controller is # 3035-P.
view full answer...
- How to Bypass Factory Brake Controller of 2006 Ford F-350The fault message is pretty vague so it's hard to give a specific area where the problem may be, but first place to check is the grounds of the trailer wiring. You also might just have a dirty trailer wiring connector that needs to be cleaned to allow the contact to be made better. We see that quite a bit. Taking sandpaper to the pins of the trailer connector usually clears that right up.
view full answer... - Troubleshooting Disc Brake Performance on Fifth Wheel Towed by 2005 Ford F350 with OEM Brake ControlIf your pads and rotors are in good shape, your electric over hydraulic actuator is functioning properly and you are satisfied with the braking performance, I believe you are in pretty good shape. Having the controller set to 8 or 9 might not necessarily indicate a problem. Typically, you would want to adjust the output of the controller so that the trailer and tow vehicle brake at the same rate, and neither the tow vehicle nor the trailer braking system are doing all the work. If having...
view full answer... - Replacing OEM Brake Controller in 2006 Ford F250 With Tekonsha Prodigy # 90885Ford had some issues with the OE brake controller on the 2005-6 Super Duty trucks. Bypassing the OE controller and installing an aftermarket model like the # 90885 Tekonsha Prodigy is a common procedure. We actually have a help article that addresses this, to see it click the provided link. The aftermarket controller would install under the dash, and you'd simply leave the OEM unit in place, so you won't have a hole in your dash. The aftermarket controller would use the # 3065-P wiring...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Written by:
Lindsey S
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Rachael H
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Michael B
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Heather A.
3/28/2018
Bill,Thank you for your review. I see that you have a 2005 Ford F-250 super duty. If your Ford came with a factory brake controller that you replaced with an aftermarket controller, then the TBC error code will display on your dash. Your local ford dealer should be able to deactivate the TBC error code.