Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
(1994 reviews)
Price: $44.34
In Stock
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Item # C45522
Retail:$63.68
Our Price: $44.34
You Save: 30%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (1994)
- Q & A (0)
- Photos
CURT Trailer Hitch Ball Mount - C45522
- Fits 1-1/4 Inch Hitch
- Fixed Ball Mount
- Rise - 4 Inch
- No Ball
- 3500 lbs GTW
- Class II
- CURT
- Steel Shank - Gloss Black
- 3/4 Inch Ball Hole Diameter
Corrosion-resistant ball mount is 11-1/4" long and fits 1-1/4" x 1-1/4" trailer hitch receivers. Ball mount can be used in the rise position only.
Features:
- Sturdy, steel construction
- Corrosion-resistant, black gloss powder coat finish
- High-quality manufacturing process
- CNC machined for strong, consistent cuts and welds
- 7-Stage washing method delivers smooth, clean surface
- Drawbar can be used in rise position only
- Hitch pin and clip or hitch lock sold separately
- Assembled in the USA
Specs:
- Application: 1-1/4" x 1-1/4" trailer hitch receivers
- Compatible with Curt Class I and Class II hitches
- Gross towing weight: 3,500 lbs
- Tongue weight: 350 lbs
- Ball hole diameter: 3/4"
- Length: 11-1/4" from center of hitch pin hole to center of ball hole
- Rise: 3-1/8" from top of inside of hitch opening
D-221 45522 Curt Ball Mount - 1-1/4" - Class II
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
Customer Reviews
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs - C45522
Average Customer Rating: 4.8 out of 5 stars (1994 Customer Reviews)
Corrosion-resistant ball mount is 11-1/4" long and fits 1-1/4" x 1-1/4" trailer hitch receivers. Ball mount can be used in the rise position only.by: Christian06/10/2018
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
by: Brad H.09/20/2017
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
Brad H.
9/24/2018
Very happy with products all high quality feel confident using. Thanks
by: Ed10/08/2022
It was the perfect size for my 2018 Chevy Cruze, coming up around the rear bumper with plenty of room yet could tow over 2,000 lbs. Trailer height to trailer hitch height was perfect.
by: Randall 07/29/2015
Very good ball mount. I have it on a 2012 Toyota Corolla S with 16" wheels. If I had to do it over again, I'd get a lower rise since the 3-1/8" rise on this model seems a little high for my car, but no big deal. I might also get a little shorter one since this mount is 11-1/4" long, but again no big deal. I'm keeping ball mount, it's also good protection if I ever get rear-ended in my small car (it's happened before and my truck sustained no damage whatsoever thanks to ball mount--unlike the car that rear-ended my truck).
by: J R 06/15/2016
Not much to say! really ! I had ordered another hitch for a certain height so I could have clearance of the hitch from the rear door of my Toyota Rav4, the size was perfect, the Mini-Camper-Utility trailer sits 1 inch off level tilting forward , when loaded it sits perfectly level, I can open the rear door 3/4's its full swing, It came in the post wonderfully wrapped, came on time, I have made purchases from etrailer in the past with spectacular service, a follow up e mail that, should I have any problems it would be taken care of. I highly recommend etrailer to all, and a big thank you to Ms. Ashley E. for a spectacular service. Jim Raymond Massachusetts
by: Randy 11/10/2020
Awesome drawbar! The order process was smooth and flawless from beginning to end. Shipment was fast and accurate. I would highly recommend etrailer for all of your trailering needs!
Randy
11/11/2021
I’ve used this product several times over the past year and it continuously works flawlessly!
by: Keith 03/01/2021
My hitch receiver is low to the ground on a Honda Civic. This raised my hitch ball about 4" so my kayak trailer tows level, and is now less likely to bottom out on a driveway.
by: Larry S.03/26/2015
Ordered all three items on 3/16/15 and it was delivered 4 days later (3/20/15) as promised. Can't say enough about what excellent customer service this order system was and very simple to use. The promised date of delivery was right on the money.
I've already installed the hitch and wire assembly and the instructions were very easy to follow.
Thank you
by: Bill E.04/25/2013
Installed the drawbar...fits easily into the receiver and looks to be a good height when combined with the C12252 Curt trailer hitch receiver on the 2012 Impala. Didn't rate excellent because I haven't used it to tow yet.
by: Kurt07/29/2018
I received this receiver about 5:00 PM only three days after ordering it. I called the customer and he delivered his car at 7:00 PM. I installed the the receiver, the taillight converter and wiring, called the customer back and He picked it up ready to tow his trailer by 8:15 PM. That is amazing. Flawless fit and function. That is how to satisfy a customer.
by: Louie08/16/2018
got it in yesterday, very very fast shipping and delivery.
I am well pleased with the product, cannot complain about it craftsmanship at all, very well built.
I added a rattle reducer along with this, I do recommend anyone putting a rattle/noise reducer on along with not only this but with any hitch insert.
plain and simple they all will rattle and make noise..
but overall I recommend this to anyone... you will not be disappointed.
Mine is on my 2016 KIA Soul, 2.0 L
I have one of the Scoota Trailers designed to haul my mobility scooter...
by: Mick 09/17/2019
Great!!! etrailer has great selection, prices and quality. I always buy from them! I bought Chevy Malibu class one hitch to pull our jet ski, no issues, still have it installed!
by: Wally S.02/25/2017
This item is what I was looking for. I needed a longer ball mount and this fits the bill. It is well made and it fits good, it's not sloppy in the receiver like some other brand names. Shipping was fast.
by: Keith05/05/2018
Fits well but did not have the pin for the receiver extension. I purchased both extension and hitch from this site and would have figured it would be complete.
by: Josue08/06/2021
This drawbar is exactly what I needed. It attaches to the hitch with no noticeable issue, and clears the rear bumper. Excellent!
by: Chris10/17/2013
Good product, sturdy and made out of solid steel. Before ordering I suggest measuring the distance from the hitch pin hole to the back of the bumper. The first ball mount I received was unfortunately not long enough
by: Tony G.09/11/2013
Drawbar came as described and fit the 1.25" receiver without problem. Purchase was on the doorstep earlier than delivery time estimate when ordered. This was my second purchase with absolutely no issues. A great place to do business.
by: Richard S.10/18/2014
Received the hitch components promptly and in excellent condition. Followed the video instructions and had a successful installation without a "hitch". The sales tech was very helpful.
by: Clarence S04/07/2016
I just got my order,Katherina could not have been better,ever thing was just like it
should be,When I call to ask about the hitch I was not going to order that day but
she was so helpful that I ordered then,it took three days to get here,I'm putting
it on a 2007 Chev. Impala,I don't have a camera to take any pictures but I know it
will fit fine.I will be telling all my friends about you. Thank you Katherina
Clarence S
by: David Dinnell07/10/2015
Ease of install--Great. Worse part exhaust lowering. Other than that product is great. Wire harness install- a five year old could do it. very satisfied will always come to you, have now got my business.
by: Dennis11/12/2017
I have a small cargo trailer and this works great, the right length and rise.
by: Tsearl06/12/2020
Great Quality and Price - directions and online video was perfect and easy to follow for installation.
by: Jeff B03/06/2017
Fast shipping, everything I ordered arrived in perfect shape. I would definitely recommend etrailer.com to my friends and family.
by: Rich09/12/2015
The product was shipped quick. The hitch is an excellent piece of equipment, looks great. Thank you for your continued quality and customer service.
by: Tim C.10/13/2017
My only complaint is that I didn't know what size the hole is for the pin, so I ended up ordering the wrong size pin. Other than that, it is a good solid product.
25
1988
Show More Reviews
See what our Experts say about this CURT Trailer Hitch Ball Mount
- Recommended Extended Ball Mount With Rise To Keep Trailer From Hitting The GroundIt sounds like you need a new ball mount. We do have ball mounts that have a rise, which would lift the coupler of your trailer and possibly give you the clearance you need. If you have a 1-1/4 inch trailer hitch receiver opening and need about 3-1/8 inches of additional clearance I recommend part # C45522. This measures 11-1/4 inches from the center of the hitch pin hole to the ball mount hole which should give you plenty of additional room to keep from mashing your hand. If you have...
view full answer... - Recommended Trailer Hitch for 2008 Volvo C70 ConvertibleThe Curt Trailer Hitch Receiver # C11065 is the only available trailer hitch that is confirmed to fit your 2008 Volvo C70 Convertible. This is a Class I hitch that will provide a 1-1/4 inch receiver opening. If you are looking to pull a lightweight trailer, I recommend checking the towing capacities for your vehicle as listed in the owner's manual to ensure you stay under its limit. I have attached the installation details for you to check out. For trailer lighting, I recommend installing...
view full answer... - Correct Ball Mount for Curt Trailer Hitch Receiver 11307 on 2010 Cadillac CTS SedanFor a Class I hitch that fits your 2010 Cadillac CTS such as the Curt Trailer Hitch Receiver # C11307, the hitch manufacturer specifies the exact ball mount that you will need to use with the hitch. For this hitch, the one that Curt specifies will be plenty long enough at 11-1/4 inches long, the Curt Drawbar # C45522. With this ball mount you will also need the Pin and Clip # C21410 and a hitch ball (which depends on the size of your trailer's coupler), either 1-7/8" Hitch Ball # C40001...
view full answer... - Does Installation Of Curt Trailer Hitch On 1993 Lincoln Mark Vlll Require Any Vehicle ModificationPer the attached installation instructions for the Curt Trailer Hitch Receiver, part # C12053, you do not have to modify your Lincoln. There is mention that you may have to enlarge one of the holes when installing the carriage bolt, but there is no other modification required. When installing this hitch you do have to remove the exhaust hanger brackets on both sides of the vehicle. The hitch is a Class ll hitch and it has a 1-1/4 inch receiver opening. A note from Curt states that All...
view full answer... - Trailer Hitch for a 1998 Ford Taurus with Dual ExhaustI spoke with my contact over at Curt and he said that for a 1998 Ford Taurus with dual exhaust trailer hitch # C12232 will fit. If you plan on doing some towing the correct ball mount is # C45522 and for a 1-7/8 inch ball use # C40001 and for a 2 inch ball use # C40018. For trailer wiring use # HM40565 if you have a sedan and use # HM48895 if you have a wagon.
view full answer... - Trailer Hitch And Wiring Recommendation For 2012 Chevrolet CruzeFrom the research I found, the 2012 Chevrolet Cruze has a towing capacity of 1,000 lbs. The Curt Hitch, part # C11282, will work for you. This is a Class l hitch and has a 1-1/4 inch receiver opening. All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps like part # 18050. Failure to properly support these loads will void your hitch warranty from Curt. To tow a trailer you will need ball mount # C45522, pin and clip # F-4, and a...
view full answer... - Recommended Trailer Hitch Receiver, Ball Mount and Wiring For a 2013 Chrysler 200With the Curt Trailer Hitch Receiver # C11133 on your 2013 Chrysler 200, Curt recommends using one of the following ball mounts. First is the Curt Class II Drawbar # C45522 with either a 1-7/8" Ball # C40001 or 2" Ball # C40018. Or you can choose one of their Euro Style Ball Mounts with a 1-7/8" # C45591 or 2" # C45592 ball. Whichever you choose you will need a Curt Hitch Pin and Clip # F-4 to secure it in your receiver. You will also need a Vehicle Wiring Harness # C56211 to control...
view full answer... - Can the Curt Trailer Hitch C11371 be Used to Tow a Trailer with a 2014 Chevrolet Cruze The Curt Trailer Hitch Receiver part # C11371 can absolutely be used to tow a U-Haul trailer. However, the towing capacity of your Cruze is only 1,000 lbs so the trailer cannot exceed this figure. I was able to look up a few of the U-Haul trailers and there are some under this capacity. In addition to the above trailer hitch you will also need a trailer wiring harness like the Curt T-Connector Vehicle Wiring Harness part # C56214, a ball mount like the Curt Drawbar part # C45522, and...
view full answer... - Trailer Hitch fit for a 2008 Pontiac Grand Prix GXPI checked with Curt and they do not have any fit exclusions for the Curt hitch part # C12225 for the GXP models of the 2008 Pontiac Grand Prix so it would work well on your GXP model. For a ball mount you would want the part # C45522 and then for a ball part # C40001 for a -7/8 inch ball or part # C40018 for a 2 inch ball. For trailer wiring you would want to go with the # 56076.
view full answer... - What Size Trailer Can Be Towed With The Draw-Tite Hitch # C12051 On A 2008 Chevrolet MalibuThe Curt Class II 1-1/4 Inch Hitch, part # C12051, will fit a 2008 Chevrolet Malibu. It is a 1-1/4 inch hitch with a gross towing weight capacity of 3500 lbs. The 2008 Malibu will only have a towing capacity of 1000 lbs. So the vehicles towing capacity is what will limit you to how much you can tow. A towing systems capacity is limited by the lowest capacity in the whole system, in your case it is the vehicle at 1000 lbs. I am including a link to the installation instructions on the Curt...
view full answer... - Trailer Hitch Receiver for Towing With a 2015 Kia CadenzaI recommend the Curt Trailer Hitch Receiver # C12118 on your 2015 Kia Cadenza. This hitch has a tongue weight rating of 350lbs and 3,500lb trailer rating. You will want to ensure that you do not exceed the weight ratings given by the manufacturer for your vehicle. This will not require you to change your rear shocks. If your suspension is sagging you should check that the weight on the trailer is distributed properly across the trailer and you do not have to much tongue weight. You typically...
view full answer... - Recommended Way to Tow a Electric Wheelchair with a 2013 Chrysler 200 Sedan or ConvertibleThe most popular hitch for a 2013 Chrysler 200 Sedan or Convertible is the Curt Class I trailer hitch # C11133. I wouldn't recommended using a cargo carrier to carry an electric wheelchair with a Class I hitch because your maximum tongue weight is 200 pounds. Based on the wheelchair carriers weighing roughly 90 pounds and electric wheelchairs around 200 pounds it will exceed the 200 pound maximum tongue weight. The best option to carry the electric wheelchair is by a trailer because...
view full answer... - Trailer Hitch and Wiring for a 2014 Chrysler 200 LX SedanYes, you are correct. Curt hitch # C11133 is a fit for your 2014 Chrysler 200. The recommended ball mount is # C45522 and for a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring you can use # C56211. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. Curt...
view full answer... - Parts Needed to Tow Trailer with 2013 Dodge AvengerIf you had a small trailer for your motorcycle you could tow it with your 2013 Dodge Avenger with the Curt hitch part # C11133 installed but if you were thinking about using a motorcycle carrier there's no safe way to do this with your Avenger. For trailer wiring you'd then want the part # C56211 which installs pretty easily. Then for a ball mount part # C45522 and hitch ball # C40001.
view full answer... - Availability of Trailer Hitch to Fit 2000 Mercury Sable, 1998 Ford Taurus and 2005 Ford TaurusWe do offer one trailer hitch receiver, Curt Class II hitch # C12232, that can fit all three of your vehicles. This 1-1/4-inch hitch will fit the 2000 Sable, both sedan and wagon; it will fit the sedan, SHO and wagon versions of the 1998 Taurus; and it will also fit both sedan and wagon versions of the 2005 Taurus. You are lucky! This kind of compatibility does not happen too often. If you plan to tow you will need ball mount # C45522 and either 1-7/8-inch ball # 19256 or 2-inch # 19258....
view full answer... - Recommended Ball Mount and Hitch Ball for a 2012 Subaru Outback Wagon with 1-1/4 inch ReceiverWhen measuring to see if you need a ball mount with a Rise or Drop you will want to make sure that your 2012 Subaru Outback Wagon is level and you will want to measure from the ground to the top of the trailer hitch receiver. For your trailer you will want to park it on level ground and measure from the ground to the bottom of the coupler. The difference between these 2 numbers will determine if you need a ball mount with a Rise or Drop. I have attached a helpful article and a picture to...
view full answer...
- Trailer Hitch for 2007 Jeep Grand Cherokee SRT8 with Center-Positioned Dual ExhaustYes, the Curt Class I Trailer Hitch Receiver # C11103 is a confirmed fit on the 2007 Jeep Grand Cherokee SRT8 with center-positioned dual exhaust. I confirmed compatibility with Curt's fit guide and also with one of their technicians. The written instructions and a helpful installation article are both linked to assist you. Tools required are listed in the instructions. If you plan to tow you will also need trailer wiring; use part # HM40975-11933 if you have the factory tow package or...
view full answer... - Which Trailer Hitch Is Recommended For A 2013 Chevy CruzeThe 3 trailer hitches we currently offer are Class-I rated and will fit your 2013 Chevy Cruze. Unfortunately, Class-II trailer hitches are not a fit for your 2013 Chevy Cruze. At the moment, the most popular trailer hitch is the Curt # C11282. It is custom fit for your Cruze and has a maximum gross trailer weight of 2,000 pounds and maximum tongue weight of 200 pounds. I also included a link showing all 3 custom fit trailer hitches too. If you will be doing some light duty towing with...
view full answer... - Ball Mount Recommendation for 2005 Volvo V50 with Curt Trailer Hitch InstalledFor the Curt hitch part # C11438 that you have installed on your 2005 Volvo V50i has a recommended ball mount, part # C45522. This is a couple inches longer than the # C45561 you currently have so it would give you the clearance you'd need. For a 2 inch hitch ball you'd want the part # C40018 or for a 1-7/8 inch ball part # C40001.
view full answer... - Recommended Trailer Hitch for 2001 Ford Taurus SEI do have a trailer hitch recommendation for you 2001 Ford Taurus, however since the two models you're referring to are two different generations the hitch you have on the 92 will not fit. I suggest, instead, the Curt Class II # C12232. It's custom fit for your Taurus and doesn't require any drilling to install. For a new wiring harness, you will need the Curt # C55375. And a ball mount # C45522. Hitch ball # 19258 will fit the mount. I've included videos of the items for you to...
view full answer... - Curt Trailer Hitch with Ball Mount for a 2013 Volvo C70 T5 ConvertibleYes, you are correct. Hitch # C11065 is confirmed to fit your 2013 Volvo C70 T5 Convertible. The recommended ball mount is # C45522. If you need a ball with which to tow you can use # C40001 for a 1-7/8 inch or # C40018 for a 2 inch. The Curt wiring harness that you also ordered, # C56119, is a fit as well. So it sounds like you are good to go!
view full answer... - Recommended Trailer Hitch and Ball Mount for 2013 Chevy Impala to Tow a Utility TrailerFor your 2013 Chevy Impala, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" # C12252. This is a custom fit that will allow you to use the Curt Class II Drawbar # C45522 along with hitch ball # C40018 and pin/clip # F-4. If you need trailer wiring, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118417 which will plug into the factory harness located behind the passenger side tail light assembly. Then you will be able to...
view full answer...
- Which Trailer Hitch and Wiring Kit Fits 1979 Buick ElectraFor your 1979 Buick Electra the Curt hitch part # C12009 is actually the correct fit and not the one you mentioned as it fits other vehicles that are much different. Then for a trailer wiring kit the Curt part # C59236 is the best option for you. For a ball mount then the part # C45522 is the correct one for the hitch mentioned. For hitch balls you'd want the part # C40018 for a 2 inch ball or part # C40001 for a 1-7/8 inch ball.
view full answer... - Trailer Hitch for 2002 Cadillac Eldorado for Towing Motorcycle TrailerThe Curt hitch part # C12068 that you referenced has a trailer towing capacity of 3,500 lbs so it would easily handle a small trailer that has a 700 lb motorcycle loaded in it. For trailer wiring you'd then want the part # C59236 which is a confirmed fit. For a ball mount part # C45522, 2 inch ball part # C40018, or 1-7/8 inch ball # C40001. Be sure to check the owners manual of your vehicle for the towing capacity as well.
view full answer...
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
Written by:
Lindsey S
Installed by:
Jeff D
Installed by:
Cole B
Installed by:
Bradley B
Expert Research:
Jameson C
Video Edited:
Jacob T
Video by:
Dustin K
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Mike S
Updated by:
Isabelle B
Updated by:
Carrie F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Christian D.
6/10/2019
I stand by my review completely. Super rigid drawbar and powder coating has held up well. Not much to go wrong with it and I am still amazed at its strength.