Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K

See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Class II Ball Mount Does Not Fit in a Class I Receiver Hitch
  Class I and class II hitches both have an 1-1/4 x 1-1/4 inch receiver openings. However, a class I hitch has a towing capacity of 2000 lbs and a tongue weight of 200 lbs, a class II hitch has a towing capacity of 3500 lbs and a tongue weight of 300 lbs. Because of the differences in capacity, the hitch manufacturer designs the receiver shank depth in different sizes. The class I hitch is not as deep as a class II hitch, as you have discovered. The Hidden Hitch Class I Trailer Hitch, part...
  view full answer...
• Will the 1-1/4" Drop Draw Tite Drawbar Work with 1-1/2" Drop Needed for Trailer
  The Draw Tite Drawbar part # 36053 would work great on a vehicle/trailer 1-1/2" apart since the vehicle would likely sag some either from cargo or the trailer therefore the 1-1/4" drop the above drawbar offers will still work great. This is also your best option as we do not currently offer any 1-1/4" drawbars with an exact 1-1/2" drop. The drawbar comes with a hitch pin but if you need a hitch ball use part # 19258.
  view full answer...
• Can A Ball Mount be Flipped for the Correct Amount of Rise/Drop
  The Curt Class I Drawbar part # C45019 can be installed right side up which will give you a rise of 5/8" or upside down which will give you a drop of 1-1/4". However, the above ball mount is only rated for use with trailers up to 2,000 lbs therefore I cannot recommend you use this ball mount to tow a 2,500 lb trailer. For a similar ball mount with equal rise/drop, I recommend the Draw Tite Drawbar part # 36053 which is rated for use with trailers up to 3,500 lbs. I have attached a review...
  view full answer...
• Hitch Ball Recommendation for Use with Ball Mount part # 36053
  For a 2 inch ball to use in the ball mount part # 36053 you would want the part # 19258. For a 1-7/8 inch ball you would want the part # 19254. Both of these balls have shank diameters of 3/4 inches. Length of the threaded portion of the shank isn't super important but the two I mentioned are confirmed fits and both have different lengths.
  view full answer...
• Will the Draw-Tite Class II Custom Fit Trailer Hitch # 36247 Work on a 1999 Isuzu Amigo 3.2 L
  Yes, the Draw-Tite Class II Custom Fit Trailer Hitch, item # 36247, will fit on the 1999 Isuzu Amigo with 3.2 Liter engine, as long as your vehicle came with the tailgate mounted spare tire, most do. If your vehicle has the spare located under the vehicle this hitch will not work and there is not a hitch available at this time. I have linked installation instructions for you to review. Some items you may want to consider, to complete your Class II towing setup are listed below. Drawbar...
  view full answer...
• Troubleshooting Draw-Tite Ball Mount and Curt 1-1/4 Inch Trailer Hitch Receiver Rattle
  I recommend measuring the inside of the hitch receiver opening and then measuring the shank of the draw bar. It may be that one of them is outside of the tolerances. If neither are obviously mis-manufactured then the best solution to your issue is to use the Roadmaster Quiet Hitch for 1-1/4" Trailer Hitches item # RM-061-125 which will ensure the tight fit in your hitch receiver.
  view full answer...
• Correct Ballmount for a 2008 Subaru Outback
  Both Class I and Class II trailer hitches are tested and rated with the specific ball mount for that hitch, therefore the ballmount used must be the one that is recommended by the trailer hitch receiver manufacturer. If your vehicle is equipped with a factory Class I, or Class II I can make the following recommendations based on the manufacturer. Class I or Class II hitch that is manufactured by Curt I recommend the # C45519 ball mount. Class II hitch that is manufactured by Draw-Tite,...
  view full answer...
• Recommendations on a Ball Mount and Lock to Fit a 2011 Honda Odyssey with a 12 inch Hitch Height.
  You will need two measurements and a little math to determine the correct ball mount for Honda Odyssey. You will need to measure, on level ground, your Honda's hitch height from the top of the receiver hitch opening to the ground. Next, measure from the bottom of your trailer's coupler to the level ground. The difference between these two numbers will determine the rise or drop you will need in your ball mount. I have attached a link that will show in more detail how to choose a correct...
  view full answer...
• 2001 Subaru Outback Wagon Trailer Hitch Receiver Class II - 1-1/4
  I recommend the Curt Trailer Hitch Receiver Class II - 1-1/4" # C12270. This is a confirmed fit your 2001 Subaru Outback Wagon, excluding Sport model, and has the higher tongue weight rating of our available hitches, 350 lbs. For your trailer wiring you will need the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, # C55370. For the ball mount, I suggest measuring the height first. Please see the attached links for a help article in how to do so. If the...
  view full answer...
• Recommended Trailer Hitch Receiver for 2018 Nissan Rogue Compatible with Tailgate Lift Assist
  For your 2018 Nissan Rogue SL, I recommend the Draw-Tite Trailer Hitch Receiver # 36542. This is a class II hitch receiver rated for up to 300 lbs tongue weight and well over the towing capacity of your vehicle at 3500 lbs. The ECU is not something we carry as most liftgates work just fine when you add an aftermarket hitch. The sensor that is often covered up at the hitch location just won't sense the movement, but either side of the hitch tube will work fine. If you have issues, then...
  view full answer...
• Ball Mount for 1-1/4 Inch Receiver With 50mm Hitch Ball
  The Curt Class II Euro Style Drawbar with 1-7/8" Ball # C45591 will fit a 1-1/4 inch trailer hitch receiver and secure to the hitch with Pin and Clip # F-4 but I wouldn't be able to tell you if it will fit a European trailer. It has a 1-7/8 inch hitch ball so it's not exactly the same size as a 50mm hitch ball. That said we do offer a 1-1/4 inch ball mount and 50mm hitch ball that will fit together: - Draw Tite Drawbar for 1-1/4" Hitch # 36053 The Draw-Tite does come with a pin and clip...
  view full answer...
  
• 2004 Subaru Legacy Outback Trailer Hitch with 2 Inch Receiver Opening
  There is no Class III receiver hitch available for the 2004 Subaru Legacy. We do have an adapter that will fit the class II 1-1/4 inch receiver hitch, # 80303 that would allow you to use a 2 inch accessory in your class II receiver. When using an adapter, you must take into account that your tongue weight will be reduced by 50 percent so the weight of your bikes and rack could not exceed 100 or 125 pounds, depending on which hitch you purchase. I have linked below to the hitches we carry...
  view full answer...
• Will Draw-Tite Trailer Hitch # 36284 Fit on 2000 Subaru Legacy Wagon
  After confirming with Draw-Tite, I can tell you the Draw-Tite Trailer Hitch # 36284 is a compatible fit for your 2000 Subaru Legacy Wagon. It is a custom fit for your vehicle and features bolt-on installation with no welding required. It is a 1-1/4-inch trailer hitch with a max GTW of 3500 lbs and a max tongue weight of 300 lbs. I have provided a link to the installation instructions for this hitch as well as a video showing a typical installation. If you need a drawbar for this hitch,...
  view full answer...
• Tow Ready Custom Fit Wiring Recommendation for a 1999 Isuzu Amigo
  This Tow Ready Custom Fit Vehicle Wiring, # 118360, would be the correct wiring kit for your 1999 Isuzu Amigo. Most likely the 5x8 utility trailer that you are renting will have a 4-way connector that will plug right into the 4-way trailer connector from the # 118360. I attached installation instructions for this product for you to check out also. You may also be interested in the following products to complete your tow setup: Curt Trailer Hitch # C13235 Class II Drawbar # 36053 Hitch...
  view full answer...
• Does Longer Ball Mount With 3/4 Inch Rise for Class II 1-1/4 Inch Trailer Hitch Affect Towing
  You can absolutely use a ball mount longer than your current which is 5 inches long and there will not be any type of negative affect on your towing. We do have ball mounts that will work with a Class II, 1-1/4 inch trailer hitch and that have the right amount of rise for you: - 7" Long: Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop # 36051 - 9-3/4" Long: Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop # 36053 Both of these ball mounts come with a pin and...
  view full answer...
• Trailer Hitch and Towing Accessories Recommendations for 2001 Subaru Outback Wagon
  The Draw-Tite # 36284 would be an excellent choice as long as your Outback Wagon isn't a Sport model. The best ball mount will depend on the coupler height of the trailer you're planning on using. I'll link you to an FAQ article that shows how to determine what rise/drop ball mount you'll need. Measure the distance from the inside top of the receiver tube to the ground. Then jack the trailer up so it's level, and measure the distance from the underside of the coupler to the ground. Subtract...
  view full answer...
• Fit of Draw-Tite Class II Receiver # 36280 on 2002 Saab 9-3 5 Door Hatchback
  The Draw-Tite Class II hitch you referenced, part # 36280 will fit your 2002 Saab 9-3 5-door hatchback unless it is a Viggen sub-model and unless it has the rear air dam. You should not need to trim anything, but the installation instructions specify that a 1/2 inch diameter hole needs to be drilled in the rear of the passenger-side frame member. If you look at the provided diagram, you can see a cross section drawing showing how the receiver opening would sit in regard to the frame members...
  view full answer...
  
• Dimensions For 1-1/4" Ball Mounts From Ends Of Mount To Receiver Hitch Pins
  Here are the measurements for each of the ball mounts that you requested. I took measurements from the center pin to both ends of the ball mount. I have included images with the measurements as well. Draw-Tite Drawbar # 36051 8-3/8" and 1-15/16". Curt Class II Drawbar # C45519 10-3/4" and 1-1/2". Draw Tite Drawbar # 36053 11-1/16" and 2". Curt Class I Drawbar # C45019 10-7/8" and 1-7/16".
  view full answer...
  
• Compare the Class III Draw-Tite and Curt Class II Hitch for the 2006 Subaru Outback Wagon
  Both of the hitches you mentioned are good quality hitches, are easy to install and require no drilling or welding for installation. They have very similar towing cacities: 4000 lb for the Draw-Tite and 3500 lb for the Curt. I recommend the Draw-Tite Class III Hitch, # 75560 for you 2006 Subaru Outback Wagon. This hitch provides you with a 2" receiver, which is why I believe it is the most popular hitch for your Outback Wagon. More trailers and hitch accessories (like bike racks and cargo...
  view full answer...
• Trailer Hitch Recommendation for a 2003 Saab 9-3 Convertible
  The Curt Hitch part # C11326 is listed as a fit for your 2003 Saab 9-3 convertible unless it is the SportCombi model or unless it has dual exhaust. For trailer wiring you would the part # C59496. For a ball mount part # 36053 and then for a 2 inch ball # 19258 or 1-7/8 inch ball # 19256.
  view full answer...
• Trailer Hitch, Ball Mount, Ball, and Wiring Recommendations for a 2002 Subaru Outback
  We do have a Draw-Tite trailer hitch that will fit, the Draw-Tite Trailer Hitch, # 36284, is confirmed to fit your 2002 Subaru Outback Sedan or Wagon. I have included a link to the installation instructions for reference. I have also included a video link showing the hitch being installed on a 2000 Subaru Outback Wagon. installation will be similar on your 2002 model. If you plan on doing some towing, the recommended ball mount is # 36053 with pin and clip # PC2. You can use ball # 19256...
  view full answer...
• Draw-Tite Hitch Recommendation for Ground Clearance on a 2000 Subaru Outback Wagon
  Since the CURT Trailer Hitch # C12270 will sit below the rear bumper of your 2000 Subaru Outback Wagon it will reduce the ground clearance on your vehicle. However, the Draw-Tite Trailer Hitch # 36284 will give you a little more ground clearance as the area that goes around the exhaust tip will go above the tip on the Draw-Tite hitch. Whereas, it goes below the tip on the CURT hitch. Check out the picture I attached that shows both of these hitches installed on a similar vehicle as yours. I...
  view full answer...
  
• Recommended Ball Mount And Trailer Connector Braket For Curt Hitch Receiver On 2017 Subaru Forester
  For your 2017 Subaru Forester with Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" # C12100, I recommend the Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K # 36051 simply because it is 2-3/4 inches shorter than # 36053 and you don't need that extra length when your hitch sits 3-1/2 inches back from the outer most part of the bumper. You will need a hitch ball like # 19258 for a 2 inch diameter ball or # 19256 for a 1-7/8 inch diameter ball. For...
  view full answer...
• Recommended Trailer Hitch And Wiring For 2015 Nissan Rogue
  We do not have a complete kit for all of the items you are looking for but I can make recommendations for each of the items you asked about. We have trailer hitches that have a 1-1/4 inch receiver opening that will work with your 2015 Rogue. I recommend the Draw-Tite # 36542. This is a Class ll hitch. The ball mount I recommend for the # 36542 is part # 36053. This ball mount features a 5/8 inch rise and 1-1/4 inch drop. For a 1-7/8 inch hitch ball I recommend part # 19256 and for a...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?