Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc

See what our Experts say about this Flint Hill Goods Accessories and Parts

• Recommended Mounting Bracket for Trailer Wiring for 2016 Volvo XC90
  I have a solution for you, but the Curt # C53HR does not have a spot to mount your trailer wiring harness. However, you can add one using either the Mounting Bracket 4-Pole Flat # 18144 or Curt Mounting Bracket for 7-Way Connector Plug # C67UR. The Curt bracket doesn't come with any hardware like the # 18144 but you can use some self tapping screws like the Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc # FA1131822 to mount this to the fascia.
  view full answer...
• Installing a Brake Controller in 2001 Toyota Tacoma
  Based on my research, the 2001 Toyota Tacoma did not come with a factory trailer connector. However, since you already have a 4-way connector installed on your truck, you will be able to start here for your brake controller installation. I recommend the Tekonsha Prodigy P2 Trailer Brake Controller # 90885. This is a proportional brake controller with a digital display. It will level automatically when mounted within a 360-degree vertical range. The brake controller installs in your Tacoma...
  view full answer...
• If Brake Wiring is Damaged do Trailer Brakes Need to be Changed Out
  If it's just the wiring that has been damaged then you only need to replace the brake wires. We recommend using 10 Gauge Wire # 10-1-1 and Heat Shrink Butt Connectors # DW05745-5 for the installation. Electric brake assemblies have 2 wires; 1 for power and 1 for ground. It doesn't matter which wire on the brake assembly is used for which function. Should your ground connections be damaged as well then you can use the Ring Terminal # DW05740-1 for the ground wire and the Self-Tapping Screw...
  view full answer...
• Fastest and Best Way to Connect Trailer Tail Light Wires
  Using butt connectors such as # 05731-5 is probably the fastest way to connect wires. Using a heat shrink butt connector such as # DW05744-5 would be a better, longer lasting connection. The white ground wire will need to secure to the trailer frame using a self tapping screw like # FA1131822.
  view full answer...
• Is a Light Kit Required When Using a Cargo Carrier Like the Curt # C18153
  Adding a tail light kit to a cargo carrier like the 24x60 Curt Cargo Carrier # C18151 is a great idea for better visibility, but isn't required unless the cargo that you are carrying happens to cover your tail lights. If this is the case then I recommend using the Tail Light Kit # 98174LED, along with 2 Brackets # BK70BB using Self-Tapping Screws # FA1131822. This kit will plug into the 4-Way connector at the rear of your 2014 Honda Pilot. If you do not already have a 4-Way connector then...
  view full answer...
• Adding Lights To My Hollywood Racks Sport Rider SE Hitch Bike Rack
  The only way you will be able to add lights to the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount, part # HLY84FR, is by attaching brackets to the rack and attaching lights to the brackets. You will need the following items: LED Light Kit for Draw-Tite, Tow Ready, Pro Series, and Rola Railed Cargo Carriers, part # 98174LED Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat, part # BK70BB Self-Tapping Screw...
  view full answer...
• Installation Hardware for Global Link Vise Lock Door Latch
  To install the Global Link Vise Lock for Cam-Action Door Latch # 295-000024 you can use the Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc # FA1131822.
  view full answer...
• What Screws Are Needed to Attach a Light to an Aluminum Frame
  In order to attach the Command Electronics Dual LED Trailer Tail Light - Stop, Turn, Tail, Backup - Red and Clear Lens # CE86FR to an aluminum surface you will want to use either a stainless steel, aluminum, or zinc plated screw like part # FA1131822. This is going to ensure that you do not have any corrosion problems at the point of contact between the two metals. As aluminum is a rather soft metal, you should not have any issues using self-tapping screws. I also highly recommend you use...
  view full answer...
• How To Properly Ground The Wires On Electric Drum Brakes
  Typically the ground wire would be connected to the frame of the trailer using ground screws like # FA1131822 and a ring terminal like part # DW05740-1. Using heat shrink is always recommended to help prevent corrosion. Connecting the ground to the axle technically would work, but the frame will be a much more secure location. You should be able to find a good clean spot on the frame and keep the grounds protected and out of the elements as much as possible.
  view full answer...
• Recommendation for Attaching Aluminum Diamond Plate Flooring to Utility Trailer
  To attach the aluminum diamond plate to the floor of your utility trailer, you can use self-tapping screws like # FA1131822 or something longer depending on how thick the aluminum is. I recommend using one about every square foot if possible. These particular self-tapping screws are 1-1/4 inches long and have 1/4 inch - 14 x 3/4 inch long threads. If you will be attaching the diamond plate to the metal grate on your trailer, you will need some type of anchor or lag bolts.
  view full answer...
• Do the Scissor Stabilizer Jacks Come with Install Hardware
  The Scissor Stabilizer Jacks part # TJSCHD-24-4 do not come with installation hardware. That said, we do offer the self-tapping screws you'll need for this using part # FA1131822. In regards to quantity, you'll need a total of 16.
  view full answer...
• How to Ground a License Plate Light
  If you have ensured you have power to the light using a test light similar to the LCD Digital Circuit Tester part # PTW2992 then it has to be an issue with the ground. I have always liked making a ground if the original connection doesn't work. You can move it around a little and get contact but eventually it will fail again. Instead use a self tapping screw like Self-Tapping Screw part # FA1131822 and securing the wires to it with 1/4" ring terminal part # DW05702-1. This is going to...
  view full answer...
• Hardware For Securing Trailer Stabilizer Jacks To The Trailer Frame
  When installing a Scissor Stabilizer Jack # TJSC-24 you can use Self-Tapping Screw # FA1131822 to secure it to your frame. I have linked a video below that will show you the installation of these on a travel trailer frame. Since these jacks are only for stabilizing the trailer you do not need super heavy duty fasteners. The ones we have are 1/4" and you can use up to 5/16" with the outer holes in this stabilizer.
  view full answer...
• Gauge Steel Used for etrailer Scissor Stabilizer Jacks, Mounting Hardware, and Base Pads
  Thanks for reaching out, Mark! The Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs # TJSCHD-24-4 are designed with 11 Gauge steel and install using 1/4" self-tapping screws like the Self-Tapping Screw # FA1131822. Then for base pads you just need two kits of the SnapPad SnapJack SJ for RV Scissor Jack Stabilizers # SN65FR and you'll be good to go!
  view full answer...
• Light Kit Recommendation for Hollywood Rack E-Bike Rack # HLY84FR
  We don't have anything custom fit to allow you to install lights on your Hollywood Racks SE E Bike Rack part # HLY84FR but the part # 98174LED is an LED light kit for cargo carriers that would be the best starting point we could offer. You could use the brackets # BK70BB to secure the assemblies to the rack with self tapping screws like part # FA1131822.
  view full answer...
• LED Tail Light Kit for a Curt Trailer Hitch Mount Cargo Carrier
  Since there isn't a specific light kit that will fit the Curt carrier # C18153, what you will need to do is use a light kit like # 98174LED, and then add 2 brackets part # BK70BB as they work with 6-1/2 inch oval lights. You will also need some self-tapping screws # FA1131822, or drill and use the hardware of your choice to mount the brackets. Also, ensure that your 2015 Subaru Forester has a 4-Way trailer connector to plug the light kit # 98174LED into. If you need to add trailer wiring,...
  view full answer...
• Replacement 7 Way Connector for 2020 Volkswagen Atlas
  Yes. The Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket - Vehicle End # PK11893 is designed to work as an OEM replacement if you have a factory 7 way that has been damaged and requires replacement. You would need some self tapping screws like the # FA1131822 to attach this to your vehicle. The style of connector this socket is designed to fit is found on nearly all vehicles that have 7-ways. Thankfully all of the manufacturers decided to use the same plug design which makes...
  view full answer...
  
• Hardware Used to Mount Optronics 7-Way Trailer Harness Plug Protector
  You can use whatever hardware works best for you and the location on your trailer that you want to mount the Optronics 7-Way Trailer Harness Plug Protector # ACP7B. When we installed the protector in the linked video, we used Self-Tapping Screws 1/4 Inch # FA1131822.
  view full answer...
• Ground Wire for Ceiling Light on Old Camper with Only a 12V Battery System
  To wire the RV Euro Style Interior Double Ceiling Light with Built-In Switch # RVIL22 to your old camper with 12V battery system, you will simply connect the black wire to 12V power, and then the white wire will connect to any metal that is in some way attached to your trailer frame. You will want to use a self-tapping screw like # FA1131822 along with a ring terminal like # DW05737-1. I recommend connecting your 12V power and testing the ground location before tapping to ensure function....
  view full answer...
• Trailer Warning Lights Flash in Vehicles Message Center
  The trailer warning lights flashing in your message center sounds like either a ground issue on the trailer or a corrosion problem between the trailer connectors. I would first start off by disconnecting the trailer connectors and using a bit of electrical spray to clean the pins. Once done, I would also use a bit of dielectric grease like part # 11755 between the two connectors before mating them back together to prevent future problems. Before you move onto the trailer wiring, I also...
  view full answer...
• What to Do w/ the Black and Red Wire When Wiring a 7-Way Connector
  The black wire is usually the 12v power wire that typically goes in the 11 o'clock position on the trailer side 7-way connector as you are looking directly at the front of it. It'll keep your battery charged, run an electric jack, or something along those lines. Not the end of the world if you don't have anything to run it to. Now the red wire is going to do something with your left side trailer lights if you are wiring your 7-way in a standard configuration so it's pretty important. I...
  view full answer...
  
• What Fasteners Should Be Used To Attach the CE Smith Crossmember Pad
  I do have an option for you but the cross member in your attached photo appears to be made of steel tubing which means there would be no access inside to attach a rivet for the CE Smith Crossmember Pad part # CE16870. That said, there are plenty of other fasteners you can use to attach these. I recommend standard self-tapping screws like part # FA1131822 as this will be easiest.
  view full answer...
  
• Cost Effective Wiring To Install 7-Way For Curt Echo Controller on 2008 BMW X5 With Battery in Trunk
  The Curt Trailer Connector Adapter part # C57672 can certainly be used to install a 7-Way on the 2008 BMW X5 to use the Curt Echo Wireless Brake Controller part # C51180 instead of the kit part #ETBC7L. I recommend to use the Curt trailer connector part # C57672 and the Power Wire Kit for Electric Trailer Brake Controllers part # BRK-ELECKIT because it has a shorter amount (10 feet) of 12 gauge wire since your battery is in rear cargo area. This kit also comes with all of the components...
  view full answer...
• Troubleshooting Optronics Uni-Lite LED Clearance and Side Marker Light Not Coming On with Aux Switch
  I recommend double checking your wiring for the lights. A load resistor will not be needed since the # MCL11CAKB lights are not blinking. A load resistor is designed for use when an LED is hyperflashing when used as a turn signal. You will want to run a wire from the positive terminal on the vehicle battery to the auxiliary switch, then from the switch to the first light, from the first light to the second lights, so on and so forth. The easiest way to connect all of the lights to a power...
  view full answer...

Do you have a question about this Accessories and Part?