Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
(149 reviews)
Price: $10.73
In Stock
Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
Item # UF48-979005
Retail:$23.72
Our Price: $10.73
You Save: 55%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (149)
- Q & A (0)
- Videos (1)
- Photos
Ultra-Fab Products Accessories and Parts - UF48-979005
- Camper Jacks
- Trailer Jack
- Tools
- Ultra-Fab Products
Designed to work with most scissor jacks, this unique socket is used with your power drill to extend and retract your jack up to 10 times faster than with a manual crank. Works with 3/8" drill bits.
Features:
- Socket lets you use a power drill (not included) to speed up extension and retraction of scissor jacks
- Eliminates manual cranking
- Works up to 10 times faster than hand cranking
- Easy operation with a powered drill that uses 3/8" drill bits
- Zinc-plated steel is durable and corrosion resistant
- Non-slip shank
- Hex socket measures 3/4"
- 2-Piece construction
- Lifetime warranty
48-979005 UltraFab Ultra Speed Socket
Video of Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Ultra-Fab Scissor Jack Speed Socket Power Drill Adapter Review
Speaker 1: Today, we're going to be taking a look at the Ultra-Fab speed socket power drill adapter for scissor jacks, part is UF48-979005.Here's what your adapter is going to look like. It's really straight forward setup. This is going to work with any drill that has a minimum opening of 3/8 of an inch, or it can even go into 1/4 inch bit drivers, so it's a pretty versatile setup. Basically, we're going to place it in whatever power tool we want to use, tighten that chuck down, it goes down on it. Then, we can operate our jacks.One thing to keep in mind, if you are backing the screw out, what would traditionally be loosening, that's going to lower the jack. If you go into the tightening, or if you turn it towards the right, that's going to raise the jack.
We'll start with it in reverse. You can see, that's going to be much quicker, much easy, and more simple, than using that hand crank. Especially when it gets hot, the humidity's up, bending over for an extended period of time is not something you want to do. This has been designed to work with the Ultra-Fab scissor jacks, of course, but it'll work with any scissor jack that uses a 3/4 inch socket, here on the end. Now, to raise it back up, would be the opposite process.
Turn our drill so it's tightening, and you can see right up in that stored position.Now, some scissor jacks are going to have a pin that goes through a circle, or there's going to be a flattened tab with a hole in it for J hook to go in. This isn't going to work for those applications, so that's something to keep in mind. That'll complete our look at the Ultra-Fab speed socket power drill adapter for scissor jacks.
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
- etrailer mistake
Customer Reviews
Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks - UF48-979005
Average Customer Rating: 4.9 out of 5 stars (149 Customer Reviews)
Designed to work with most scissor jacks, this unique socket is used with your power drill to extend and retract your jack up to 10 times faster than with a manual crank. Works with 3/8" drill bits.by: William 05/07/2024
exactly what i expected
by: John 01/30/2024
Works as designed!
by: Aleski11/28/2023
Just good.
by: GaryS_NC08/07/2021
If you have or use scissor jacks under your RV, you'll love this accessory. Just insert it in your cordless drill and in seconds you'll have your jacks extended or retracted. This is a must have! Having a hand crank in addition is also a must to tweak the jacks extension height or if your drill battery dies.
by: Christopher 11/06/2023
Great fit!!!!
by: Steve C05/27/2017
Excellent product - it was just what I needed - thanks for the quick service - this will be a real benefit to me as I have had a stroke and need the assistance in lowering my trailer jacks ... suggest and add-on of axle grease for the jack screws..
Steve C.
5/27/2018
Works great - used several times - so much easier to set up the trailer now
by: Gary08/14/2023
Easy to mount
by: Biro07/03/2023
Great 2nd socket to have as a spare.
by: William05/05/2018
Just the right amount of extension to more easily deploy my leveling jacks.
William C.
5/6/2019
Still does the job.
by: Jeff 06/20/2023
Purchased as a spare. Current one is one-piece and a real time saver.
by: Erik D.12/24/2017
Couldn't do without this tool. Makes operating the trailer stabilizers quick and easy.
Erik D.
12/24/2018
works great!
by: Bob 11/03/2022
I needed some front end stabilizers for our 19 ft Jayco. These work perfectly... ot too heavy and not too light.
by: Glenn B11/16/2022
etrailer is my go to place when I need something that they sell
by: Rich A07/05/2020
This socket saves a ton of time setting up and taking down my stabilizer jacks with the drill that I keep in my trailer. I can recommend it to anyone who would rather spend their time playing when camping instead of working.
by: double E10/30/2018
I am very happy with the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks. It works just as advertised. I own a cordless impact driver and experimented with chucking up a 3/4" socket to raise and lower the jacks. Don't do it that way! You stand in jeopardy of damaging the jack. Using a convention cordless drill-driver to slowly spin the fitting still requires caution, but is much better. Just remember; once the jack makes contact with the ground, switch over to hand cranking the last few revs. to firm up.
by: Robert F04/30/2023
Very handy piece of equipment to make RVing easier. Appears well made but a tad on the pricey side for the convenience.
by: PeteD11/25/2016
I use this in my drill to quickly adjust the weight distribution on my Hensley hitch. Saves time and effort a wrench would require.
by: Vince H.08/27/2015
I bought 2 sets of the 24" ultra-fab scissor jacks and the speed socket. My small 12v cordless drill runs these up and down just fine.
I am looking forward to the reduced movement in my large fifth wheel trailer while these jacks are deployed.
by: Wendell07/06/2019
Lifts quickly with impact wrench.
Wendell L.
7/7/2020
Never used it
by: Blubuckaroo07/14/2020
This well made adapter is perfect for using my cordless drill to lower & raise our stabilizer jacks.
It's well made and very reasonably priced.
by: andrew C.02/19/2017
This is a life safer for me. Using the drill adapter attached to a portable electric drill makes lowering and raising the four stabilizers on my trailer a breeze. No stress on my back or knees being bent over for what at times seems forever cranking by hand.
by: James B03/17/2014
Another great order from etrailer.com. My ordering was simple, the shipping was much faster than expected. The communication from them was solid, every step of process someone sent me an update.
Extremely happy with this supplier.
by: Paul P.07/22/2017
Thank you for promptly packing and shipping my order. It arrived a day earlier than expected!
This product will be a BIG help lowering and raising the RV stabilizers. You offered the best solution at the best price - plus outstanding delivery!
by: P. J.06/11/2015
1. The product is excellent! The product information says it is 10 times faster. I say 20 times faster and takes 0 effort. No more squatting over, cranking away in the heat and humidity. 5 seconds with a drill and Bam!
2. Etrailers price was excellent.
3. I used the more inexpensive of the 3 shipping options, which was $8 and it arrived in only 3 days.
Thank you Etrailer. This is my second purchase from Etariler and I will always check with Etrailer first.
by: Don S.05/08/2013
This power drill adapter is the perfect complement for our new Ultra-Fab Ultra Scissor Jacks!
25
149
Show More Reviews
See what our Experts say about this Ultra-Fab Products Accessories and Parts
- Ultra Fab Stabilizer Jacks for Minnie Winnie MotorhomeThe Ultra Fab # UF39-941704 is the manual version of this stabilizer. For the electric version use the Ultra Fab # UF39-941705 rated for 6000 pounds. The angle brackets screw into the RV frame. You may have to drill some holes. It might be possible to install a set on your Minnie Winnie 31K but there isn't a lot of space on the underside of that RV so it is possible, even likely, that the stabilizers will not fit. When fully retracted the stabilizers will hang down 5 inches from where...
view full answer... - Are Replacement Parts For Scissor Jack AvailableI spoke with my contact at Stromberg Carlson about replacement parts for the scissor jacks we offer like part # JSC-24-IND, and they told me they do not offer any replacement parts. I recommend replacing your current jack with the # JSC-24-IND. This is a 5,000 lb leveling jack that has measures 4 inches when retracted and 24 inches when extended. The required crank handle can be ordered separately and that part number is # JCH-1. If you choose to use a power drill to raise and lower...
view full answer... - Can the Dutton-Lanison Drill Drive Socket Adapter Be Used to Raise/Lower the Roof On a Jayco Pop UpI cannot say for certain, but I can say that the Dutton-Lainson Drill Drive Socket Adapter for DLB Series Winches # DL6456 is specifically designed to fit into the square tub hub on the 6453, 6454, and 6463 handle kits. If the roof for your Jayco pop up just uses a standard hex socket to raise and lower, then you'd just have to let me know what size it is and I'd be happy to find the right adapter for you. For example, if you needed a 3/4" socket adapter for your camper you'd need the...
view full answer... - Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of TrailerFor your Sure Trac ST9614 HLODOD-B-140 trailer I recommend adding the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs - Qty 2 # UF48-979002. I believe these will work well to stabilize your trailer for loading. They can be adjusted using the hand crank or you can use the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005 if you prefer. If you want more of a solid mount drop leg stabilizer that you would weld on, we have the Square Drop Leg Stabilizer Jack...
view full answer...
- Recommended Leveling Jacks For Winnebago ViewThe Stabilizer Jack you came from, part # TJ01RT can be permanently mounted typically under the corners of your camper. Each jack has a 650-lb capacity and are sold individually, and are designed for a smaller RV than your View. The stabilizer jacks I recommend for your Winnebago View are the Stromberg Carlson Leveling Scissor Jacks, part # JSC-24-IND. These jacks mount on the corners of your camper and adjust from 4 inches to 24 inches as needed. Each jack has a capacity of 5,000-lbs....
view full answer... - Can Ultra-Fab Power Twin II Electric Stabilizers be Installed on a Mercedes Benz Sprinter Cargo VanUltra-Fab Power Twin II Electric Stabilizer # UF39-941705 is designed for trailers but technically it could be installed on your Mercedes Sprinter cargo van. The only issues that you could run into are limited available frame space on the Sprinter and ground clearance. What I recommend is to use a couple of scissor jacks such as # UF48-979002 with the electric drill adapter bit, # UF48-979005 (to raise and lower the jacks fast). I would leave them detached from the vehicle though to eliminate...
view full answer... - Reducing Movement in a 5th Wheel Trailer While ParkedMovement is normal when it isn't controlled. But when stabilization products are used then the movement can be reduced if not eliminated. You mentioned that you have tried things to correct this problem but did not mention what those things were so some of my recommendations may be something you have already tried. First we have to determine the nature of the movement. Is it side to side, front to back, or both? The front to back movement can result from slight movement at the trailer...
view full answer... - What Is Retracted Height Of Ultra-Fab Products Camper JackThe Ultra-Fab Products Camper Jack, part # UF48-979006 measures 4-3/4 inches tall when fully retracted. The jack has a 24-inch lift and has a large footplate that measures 4-1/2 inches wide and 9-inches long, and this jack has a 6,500-lb support weight capacity. The crank handle is not included with the jack. For the handle you would need part # UF48-879100. To make the job a lot easier you can use the Ultra-Fab Speed Socket Power Drill Adapter, part # UF48-979005. This will work with...
view full answer...
- What Can I Do For A Malfunctioning Level Jack If I Have A Couple Of Days Before The Start Of My TripMy recommendation would be to replace the broken leveling jack, but it appears you might not have time to have it done. So I think you should get the Leveling Scissor Jack Set - 30" Lift - 10,000 lbs - QTY 2, part # JSC-30, instead. You will get two heavy duty scissor jacks that can be bolted or welded to your 2016 Jayco Pinnacle 36 FBTS. Each of the jacks is rated for up to 5,000 lbs. You will not be able to lift your fifth wheel with this jack, but you should be able to pair it with the...
view full answer... - Recommended Stabilizer Jacks to Reduce Trailer RockingThe etrailer.com Stabilizer Drop Leg Jacks # TJ01RT-HD are rated to 1,000 pounds per jack and would help with rocking, but can be a little limited due to having 6 1/4 inches of drop. The etrailer.com Scissor Jacks # e99012 would offer not only a higher capacity of 5,000 pounds per jack, they would also get you 24 inches of lift, if needed. Scissor jacks can be a bit of a pain to get into position, however, so the Ultra-Fab Speed Socket # UF48-979005 that attaches to a drill does make lifting...
view full answer... - What Size Socket Fits on the Ultra-Fab Ultra Scissor Trailer JackThe not that turns the worm gear on the Ultra Fab jack, # UF48-979006, is a 3/4 inch. You can use the Ultra Fab speed socket, # UF48-979005 with a drill that accepts 3/8 inch drive bits to extend/retract the jack faster.
view full answer... - Will the Ultra-Fab Scissor Jack Fit a 32 Foot North Trail TrailerThe collapsed height of the Ultra-Fab scissor jack # UF48-979032 is 4-3/4 inches leaving you with 19-1/4 inches of clearance from the ground to the bottom of the jack. The jack also has multiple holes for mounting to any frame or it can be welded on by a qualified professional. Because it is so versatile, this would be a great choice for your trailer. You might also be interested in the speed socket power drill adapter # UF48-979005 to make lowering and raising the jack faster. It can...
view full answer... - Recommended Scissor Jacks To Stabilize Winnebago View Sprinter To stabilize your Winnebago View Sprinter frame I recommend using scissor jacks like part # JSC-24-IND on the rear corners of your Sprinter. I recommend using 2 jacks. This jack can be bolted or welded when installing. Welding should be done by a certified professional. I recommend these over the # TJ01RT you came from because they have a much higher support capacity. The # TJ01RT has a support capacity of 1000 lbs versus the # JSC-24-IND that has a capacity of 5000 lbs. The # JSC-24-IND...
view full answer... - Can Ultra-Fab Power Twin II Stabilizer Jacks be Used on a 2017 Minnie Winnie 31KThe Ultra-Fab stabilizers # UF39-941705 and # UF39-941704 are very similar and have all of the same specs. But there is one important difference. Set # UF39-941704 is manually operated and # UF39-941705 comes with 2 motors for electric operation. It might be possible to install a set on your 2017 Minnie Winnie 31K but there isn't a lot of space on the underside of that RV so it is possible, even likely, that the stabilizers will not fit. When fully retracted the stabilizers will hang...
view full answer... - Is There a Socket for Stabilizer/Scissor Jacks With A Slot On An Airstream TrailerThe Ultra-Fab Speed Socket Power Drill Adapter part # UF48-979005 is essentially just a 3/4" socket. If the stabilizer jacks you have now can be raised and lowered with a 3/4" socket then the Ultra-Fab Speed Socket Power Drill Adapter will work for you. That said, it sounds like you may need to use the Ultra-Fab T-Slot Power Drill Adapter for Scissor Jacks part # UF48-979071 instead which has the slot that you referenced.
view full answer... - Recommended Stabilizer Jacks for a Mercedes Benz Sprinter 3500 RV Van Conversion I have a couple universal options you can consider to stabilize your Mercedes Benz Sprinter 3500 as there is not a custom fit option. The MORryde Hitch Mounted Stabilizer # MR22AR is a great option if you have a 2" receiver on you Sprinter. This will fit into your receiver so there is no need to drill into your frame. As it is also as far back on your Sprinter as you can go it will give you great stabilization from front to rear. We also have the 24" Ultra-Fab Ultra Scissor Jacks # UF48-979002...
view full answer... - Recommended Drill Adapter For Stabilizing Jacks On 1992 Coleman 8 Foot Pop-Up CamperThe Drill Adapter for Atwood Direct Drive 5th Wheel Landing Gear is really for the landing gear on a 5th wheel but may work well with other Atwood jacks. However, it's also been discontinued. I believe what you are looking for and recommend is the Ultra-Fab T-Slot Power Drill Adapter for Scissor Jacks # UF48-979071 that is designed to work with most scissor jacks. Another option is the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005. These drill adapters will...
view full answer... - Troubleshooting Scissor Jack Switch on Trailer that Stops Working When Switch Is PressedCheck the power and ground. It sounds like either the power or ground wires aren't able to pull enough amperage to operate the scissor jack motor or there's a problem with the motor and its wanting to draw too much amperage to operate and therefore it needs to be replaced. Make sure the battery has a good charge and the wiring is solid and also the same for the ground wire.
view full answer... - Best Recommended Scissor Jacks for 2017 Thor Vegas Class A MotorhomeThe best scissor jack you can use on your 2017 Thor Vegas motorhome is the Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs # UF39-941707. This will give you the electric motors on each side to assist with leveling as well. If you want the more standard scissor jacks, I recommend the Ultra-Fab Ultra Scissor Jacks # UF48-979002 which I also recommend the Ultra-Fab Speed Socket Power Drill Adapter # UF48-979005 for ease of function.
view full answer... - Recommended Stability Enhancement for Lippert Power Stabilizer JacksIf you are experiencing that much movement with the Lippert Components High-Speed Power Stabilizer Jack # LC298707, that is definitely not normal and I recommend checking them to ensure there is no damage to the unit. It is possible they are not mounted in the best spot for your specific trailer, but no matter the extension, they should be stabilizing your trailer to limit movement. You do have some options. You can add scissor jacks like # UF48-979002 and drill adapter # UF48-979005...
view full answer... - Can Ultra-Fab Speed Socket Power Drill Adapter be Used with Stromberg Carlson Scissor JackThe Ultra-Fab Speed Socket Power Drill Adapter # UF48-979005 can indeed be used with the Stromberg Carlson Leveling Scissor Jack # JSC-24-IND that you referenced and it will work well. This socket will be used with your power drill to extend or retract the scissor jack up to 10 times faster than with the standard manual crank. The leveling scissor jacks can be either welded or bolted to the trailer frame. A bolt-on installation will be a bit less permanent than welding the units, but...
view full answer... - Can Scissor Jacks Be Used to Level a 24 Foot Heavy Duty Car Hauler TrailerScissor jacks # UF48-979002 are meant to support weight but not lift it like you said so these jacks would not be the best option for your trailer. Scissor jack # JSC-30-IND is listed as having the ability to raise, lower, and stabilize so you could use it with handle # JCH-1. Or use drill attachment # UF48-979005 to speed up the process.
view full answer... - Best Way to Stabilize a 40 Foot Travel TrailerFor your 40 foot travel trailer, I recommend using four stabilizer jacks and two wheel stabilizers. The stabilizers jacks will need to be placed in all four corner of the trailer and for this, I recommend the Ultra-Fab Ultra Scissor Jacks part # UF48-979031 which have a 6,500 lb capacity and offer up to 30" of lift. If you have a cordless 1/4" impact you can use the speed socket part # UF48-979005 to raise/lower the jacks but if not there is a manual crank handle included. For the wheel...
view full answer... - How does the Ultra-Fab Speed Socket Power Drill Adapter Operate a Scissor JackMost scissor jacks have a 3/4 inch hex head on the crank shaft. The Ultra-Fab Speed Socket Power Drill Adapter, # UF48-979005, is a universal 3/4 inch socket that fits most standard scissor jacks. If your jack does not have a 3/4 inch hex head for the crank handle, then this socket may not work for your jack. Typically, if scissor jack manufacturers do not use a standard crank handle, then you would want to contact that manufacturer for a replacement crank handle or drill bit options...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Written by:
Lindsey S
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Jeffrey L
Video by:
Kathleen M
Installed by:
Randy B
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Halie H
Updated by:
Eric H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Garys_nc
8/14/2022
This is an absolute must have!. It makes running them and taking them down a breeze.