Installing a Brake Controller in 2001 Toyota Tacoma

Question

Question:

Thank you for the information. This is a great web site! I am looking at the etbc7 install kit. I already have the 4-7 pin connector and bracket. Can I buy everything else separately? I just want to make sure I get everything I need to install it.

asked by: Brady

0

Expert Reply:

Based on my research, the 2001 Toyota Tacoma did not come with a factory trailer connector. However, since you already have a 4-way connector installed on your truck, you will be able to start here for your brake controller installation.

I recommend the Tekonsha Prodigy P2 Trailer Brake Controller # 90885. This is a proportional brake controller with a digital display. It will level automatically when mounted within a 360-degree vertical range. The brake controller installs in your Tacoma with a universal pigtail harness included with the controller. I have attached a review video of this brake controller for you.

You will also need our universal installation kit # ETBC7. This kit will provide you with the 7- and 4-way trailer connector needed for functioning electric brakes, as well as the hardware necessary for installation. The connector from this kit will plug into your existing 4-way, as well as allow you to connect the trailer brakes with the brake controller and battery. I have attached an installation video of this kit on a 1999 Toyota Tacoma for you.

I have also attached some FAQ articles for you.

expert reply by: Victoria B

0

Brady

7/15/2015

Thank you for the information. This is a great web site! I am looking at the etbc7 install kit. I already have the 4-7 pin connector and bracket. Can I buy everything else separately? I just want to make sure I get everything I need to install it.

Reply

Victoria B.

7/15/2015

You can buy all the components of the kit separately. The # ETBC7 installation kit is something we put together for our customers. The easiest way to get the duplex wire, breakers, butt connectors, and ring terminals is to use part # 5506. In addition to that, you will also want 6 hex self-tapping screws # 101131802, a larger self-tapping screw # FA1131822, and 2 quick splice connectors # SWC502905-1. If you do not have a circuit tester, I recommend # PTW2993. The # ETBC7 kit also comes with 2 feet of 1/2 inch wire loom # 459075-1, as well as a bundle of zip ties.

Reply

Answer 1

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 2

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Installing a Brake Controller in 2001 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching