Hopkins Wiring Harness with 4-Pole Flat Trailer Connector - Trailer End - 4' Long

See what our Experts say about this Hopkins Trailer Wiring

• 4-Way Trailer Wiring Recommendation that Uses all 16 Gauge Wires
  For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector # W787264. The part # HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.
  view full answer...
• Replacement Wiring on Bully Lighted Hitch Step
  To replace your wiring on your Bully hitch step # CR-600LED I recommend the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138 along with heat shrink connectors # DW05743-5. For added protection you can add a wire loom like # 7509-1 sold by the foot. The wires of this harness have the following functions for you to match up to the wires in the step. White: ground wire Yellow: left turn/brake light Green: right turn/brake light Brown: tail lights
  view full answer...
• Converting A 5 Wire 4 Way Trailer Connector To Vehicle 4 Way Flat
  It sounds like you have a separated wiring setup with 5 wires - yellow, yellow brown, green, green brown, white. Typically, yellow is left turn / stop, green is right turn / stop, yellow brown is left running light, green brown is right running light, white is ground. You convert this to a standard 4 way by wiring the 5 wires to 4 flat harness # HM38138. This allows you to wire up all of your trailer wires color for color and then simply plug it into the vehicle's 4 way connector. The...
  view full answer...
  
• Adding A Trailer Hitch Receiver To A 2022 Vanleigh RV Beacon 39FBB 5th Wheel Trailer To Triple Tow
  To know which adjustable width trailer hitch will fit your 2022 Vanleigh RV Beacon 39FBB fifth wheel trailer you'll need to measure the distance between the inside of your frame rails. The Curt Adjustable Width Trailer Hitch Receiver for RVs # C13704 you were looking at fits a frame width of 22" to 66" Wide and has a 5,000lb GTW. If you can get me the frame width for your trailer I can find the correct fit for you. You'll also need a 4-pole connector to transfer your braking and turn...
  view full answer...
• Can Trailer with Brown Yellow and Brown Green Wires Run to Standard 4-Way
  Yes you would be able to use your current trailer wiring configuration with a standard 4-way that only has 4 wires like the # HM38138 that you referenced. Basically the yellow brown and the green brown wire would wire directly to the single brown wire of the 4-way and the other colors would match and you'd be set. What you have now is a wish bone setup that just has a separate wire for the running light circuit for each side of the trailer. We have 4-ways that are setup for this with the...
  view full answer...
• Converting Euro 7-way To Standard 4-Way Flat Trailer Connection
  I am not familiar with the bike rack with lighting, however, you can rewire the 7 pin euro by function to the 4-way flat. I recommend using the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector - Trailer End - 4' Long # HM38138 along with quick splices like # SWC501925-1 or butt connectors like # DW05744-5. The 4-way functions are: White=ground wire Yellow=left turn/brake light Green=right turn/brake light Brown=tail lights I've attached a photo of the Euro functions for you.
  view full answer...
  
• Can You Connect the Thinline LED Trailer Tail Light Red Wire to both Green and Yellow Wire
  I believe what my friend Rob was referring to when he said to connect the red wire from your Thinline LED Trailer Tail Light # STL59RB to the yellow and green wires is to connect it to the yellow and green wires of the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138. From there you can plug the Hopkins connector into your vehicle wiring harness for power if you are using this on a cargo carrier or other hitch mounted accessory. This process will not harm your vehicle...
  view full answer...
• Can 4-Pole Wiring Be Submerged Underwater
  4-pole wiring like the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138 can technically be submerged underwater but you would want to ensure that the connections are all waterproofed with heat-shrink butt connectors, like # DW05744-10, for the bare wires and some Dielectric Grease # 11755 on the 4-Pole connectors.
  view full answer...
• Parts Needed To Transfer Lighting Signals While Triple Towing An RV And Boat Trailer
  To triple tow you wouldn't be running both connectors to your Ram. You would connect the RV's 7-pole to your Ram and then connect the boat trailer to a connector on the RV. Since you just need lights for the boat trailer you'll just need a 4-pole connector # HM38138, some heat shrink butt connectors # DW05744-10, and some additional wire for length. You'll splice in the 4-pole connector to the lights on the rear of your RV to transfer your lighting signals from the RV to the boat trailer....
  view full answer...
• How to Re-Wire Trailer with 4-Pole Trailer Harness
  A 4-pole trailer wiring harness has three circuits plus a ground, the ground being carried on the white wire. You will just need to test the functions on each trailer wire to confirm how to connect them to a 4-pole pigtail like # HM38138. A junction box # 38656 and ring terminals like # 44-5310A will make it easier to get solid reliable connections. You will want to ground a battery negative terminal to the frame and apply 12V power from the positive terminal to each trailer circuit, one...
  view full answer...
• Replacing 4-Way Flat Connector With No White Ground Wire Causing Lights To Turn Off
  You are correct that you need a ground wire for your 4-way flat connector. When you are hitting bumps the coupler for the ball has a small amount of play inside which is causing your lights to turn off and on. The Hopkins Wiring Harness # HM38138 will give you a short 4' lead which you can splice into your trailer wiring and run the white wire to a good ground location on the trailer. This will ensure a good solid ground connection for the wiring on the trailer. The Heat Shrink Butt Connectors...
  view full answer...
• Can You Use The 3rd Brake Light Logic Module With A 4-Pole
  For your 2021 Chevrolet Silverado you will have to splice into the factory wiring to use the 3rd Brake Light Logic Module # PP20-702 to connect the left and right turn signals, along with the green wire. You can also combine this harness # PP20-702 with a 4 pole harness like the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138.
  view full answer...
  
• Solution for 4-Way Adapter With 4-Way Flat Male End and 4-Way Round Male End
  Your typical 4-way flat to round adapter like the # ADP001 is the opposite of what you need on both ends. Although nobody makes an adapter like this, you can easily make your own. For the 4-way flat trailer end connection you can use the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector - Trailer End - 4' Long # HM38138. You can cut the wiring harness down if you want it to be shorter but this gives you a decent amount of wire to work with. Then you will need the RoadMaster 4-Wire...
  view full answer...
  
• Availability of Adapter to Go from 4-Pole Round on Trailer to 4-Pole Flat on Vehicle
  I do have a couple options for you, but there isn't an adapter to go from a male (trailer end) 4-pole round to a female (vehicle) 4-pole flat or even a 7-way. So, you could either make your own adapter using part # PK11410 and # HM38138, if you do not want to modify the harness on your magnetic trailer lights, or you could simply replace the 4-pin round connector on them with part # HMC20031, which is going to be the most cost effective.
  view full answer...
• Do 4-Way Connectors Have a Power Wire
  Trailer and vehicle 4-way connectors like you'll find with the 4-Way Flat Trailer Wiring Kit - Vehicle and Trailer Ends # HM48205 do not actually have a hot - or power - wire. As you can see by the cut out I added of the linked help article on trailer wiring (which I highly recommend checking out), a 4-way will activate running lights, brake lights and turn signals. I have added a link to our entire selection of trailer end 4-way connectors for you to take a look at.
  view full answer...
  
• How to Connect Thinline LED Trailer Tail Light to 4 pole Connector
  To connect the Thinline LED Trailer Tail Light # STL59RB to your 2017 Kia Sportage's trailer wiring is fairly simple. It sounds like you are going to be mounting the light to a cargo carrier, or other hitch mounted accessory and would like to disconnect it easily when you're not using it. The Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138 can be wired directly into the light and then plugged into your 4 pole connector. The 4 pole connector is the trailer side, so it...
  view full answer...
  
• What Does Some Trailer Wiring Have 2 Brown Tail Light Wires
  Common 4-pole trailer wiring like # HM38138 uses one wire, the brown one, for the running lights on both sides of the trailer. Sometimes what is called a 'wishbone' harness is installed on the trailer and this simply uses two separate running light wires - brown with yellow for left and brown with green for right - to make it easier to connect to the trailer lights since that way no jumper wire will be needed to cross from one side to the other. Some examples of wishbone style 4-pole...
  view full answer...
  
• Will Adding 4-Way Wiring To a 2013 Cadillac SRX Risk Damage To The Vehicle?
  On your 2013 Cadillac SRX Luxury you want to use a wiring harness with a powered controlled module like the Curt # C59236. This module uses power from the vehicle battery to operate the lights on a trailer and reduces strain put on the factory wiring. By using a basic 4-Way # HM38138 you put all the additional power load for the trailer on the factory tail light wiring. Since manufactures have switched to using the thinnest wire power to save money this will likely overload the wiring and...
  view full answer...
• diagram
  We don't have access to the wiring color diagram unfortunately.
  view full answer...
• How To Hardwire A 4-Way Harness On A Small Utility Trailer
  In order to wire a 4-way harness onto your trailer, you will need a few simple items. The first of which will include our Deka Heat Shrink Butt Connector part # DW05744-10 and the Electrical Connector Dielectric Grease part # LT37534. The rest of the tools needed for this install should be fairly common in most toolboxes. Before you install the wires, you will need to strip back a 1/4" of the jacket from each wire and place them into opposite ends of the butt connector. After you have...
  view full answer...
• Troubleshooting Turn Signals Not Working on a 4-Pole Setup
  The first 2 things that you want to check when experiencing wiring problems is all of your grounds and the connectors on both your tow vehicle and trailer. You will want to make sure that the grounds are secure and have a metal-to-metal contact. Sometimes even some paint can cause lighting issues. To replace a damaged connector on your trailer you will need part # HM38138; for your tow vehicle you can use part # C58044. If all of that looks good then you will want to test the wiring on...
  view full answer...
• Adapter Recommendation for 6-Way on Trailer to 4-Way on Vehicle
  For a 6-way to way adapter we do have the part # A10-6034VP. With this your trailer's 6-way would plug into it and then the 4-way of the adapter would plug into the vehicle. Best solution will be to replace the 6-way on your trailer with a 4-way to match your vehicle as that will eliminate the need for an adapter. For that the part # HM38138 would be your best bet.
  view full answer...
• Troubleshooting Turn Light Fuse Blowing With Cargo Trailer
  If you add additional wire you're still going to be getting under the trailer to run it. I would go ahead and look under the trailer to check for a short in the wiring. Many times this can be found near the lights where the wire connects. It would also be a good idea to check out your connector. Make sure it is free from any debris and corrosion. If you don't find anything, instead of running a separate 4-way I would run new wire from the lights to your 7-way connector. It would also be...
  view full answer...
• Wiring Parts Needed to Power 3rd Brake Light on 2020 Toyota Tacoma Topper Shell
  We definitely have the wiring parts and connectors to help you out but you will need to do some splicing to accomplish this as there isn't a plug and play type adapter. Here are the parts I recommend: - 3rd Brake Light Logic Module # PP20-702 - Pollak Complete Assembly 2-Pole Connector # PK12200 - Deka Heat Shrink Butt Connector Kit # DW05744-5 - 18-Gauge 2-Wire Bonded Parallel Conductor Wire # SWC97FR (sold by the foot) The Logic Modul connects to your turn signals and feeds the...
  view full answer...
  

Do you have a question about this Trailer Wiring?