Can You Use The 3rd Brake Light Logic Module With A 4-Pole

Question

Question:

I purchase a 20-702 3rd brake light logic module. Can I use a 4 flat trailer connector with product? I dont want to splice into factory wiring of my 2021 chevy silverado.

asked by: Michael M

0

Expert Reply:

For your 2021 Chevrolet Silverado you will have to splice into the factory wiring to use the 3rd Brake Light Logic Module # PP20-702 to connect the left and right turn signals, along with the green wire.

You can also combine this harness # PP20-702 with a 4 pole harness like the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector # HM38138.

expert reply by: Bryce D

0

3rd Brake Light Logic Module Install Instructions
(click to enlarge)

3rd Brake Light Logic With 4 Pole
(click to enlarge)

Will

4/7/2024

I am trying this exact setup today. While the break light doesn't blink when the breaks are applied with a turn signal, the light is blinking when I remove my foot from the break with either turn signal on. Is my new module faulty?

Reply

Bryce D.

4/8/2024

@Will Not necessarily, what you're describing sounds like a grounding issue so I'd suggest checking the connection of the main ground wire of the trailer wiring harness. You'll want to make sure it is attached to a clean metal surface, or if not you can run all of the trailer wires back to the main ground.

Reply

Will

4/8/2024

@BryceD initially tried using the 4 way pin connector but have now tried going straight to Truck frame for ground but still blinks

Reply

Bryce D.

4/9/2024

@Will Interesting, it sounds like there may be some back feed from the brake circuit. I recommend installing some a diode # RM-690 on the brake wire to fix it.

Reply

Answer 1

Yes, you can use the factory trailer connector on your 2015 Nissan Titan to power the third brake light on your Leer camper shell. That said, they don't make a plug and play harness for this so you will need to do some wiring but no splicing…

view full answer...

Answer 2

You can use 7-way trailer wiring with the module part #PP20-702 to provide power to the third brake light of your camper shell/cap. Basically the stop/turn circuits of the trailer wiring need to run to the yellow wires of this module and then the…

view full answer...

Answer 3

Yes, you can connect a 3rd Brake Light Logic Module #PP20-702 to a 4-Way Flat Trailer Connector #HM48110. This will filter our the turn signals from the brake lights on your trailer connector. Then you will only need to run the power and ground wire…

view full answer...

Answer 4

If you absolutely do not want to splice into the vehicle you could use the trailer connector to power the third brake light on a truck bed camper but the issue with using the trailer connector is that the stop/turn circuits are combined. Therefore,…

view full answer...

Answer 5

The part #PP20-702 has to connect to both the left and right hand turn signal/stoplight circuits in order to separate out the stoplight. The reason that is because it waits to see voltage on both circuits at same time to then allow the stoplight…

view full answer...

Answer 6

There is a simple solution to get the isolated brake signal from your combined turn signal and brake wiring. You will simply use the Pacer Performance 3rd Brake Light Logic Module #PP20-702. The module filters out the unwanted turn signal. This will…

view full answer...

Answer 7

To isolate the brake light signal on your 2019 Chevy Silverado 2500HD you just need the Pacer Performance 3rd Brake Light Logic Module #PP20-702. You can use the attached installation instructions for the 3rd brake light on your camper shell.

view full answer...

Answer 8

If the third brake light is still flashing with the Pacer Performance 3rd Brake Light Logic Module part #PP20-702 installed then the unit is either installed incorrectly or faulty. I have attached a wiring diagram you will need to look over and make…

view full answer...

Answer 9

To fix this issue, you're just going to need to install the: -3rd Brake Light Logic Module #PP20-702. This will separate the third brake light and your turn signal lights to alleviate the flashing. Attached is a product overview video for you to…

view full answer...

Answer 10

Thanks for the picture! The 3rd Brake Light Logic Module item #PP20-702 you were looking at is exactly what you need to activate a third brake light on your 2022 Ford F-150's Overland camper topper. Once connected, this module allows the third…

view full answer...

Answer 11

Yes we do have a logic module that will work to wire your third brake light on your camper shell, part #PP20-702 the Pacer Performance 3rd Brake Light Logic Module. The logic module filters out the unwanted turn signal inputs. This prevents the third…

view full answer...

Answer 12

The best product we have for wiring third brake lights in a camper shell is the 3rd Brake Light Logic Module part #PP20-702. If you were to combine this with an in-bed wiring harness such as the Curt 5th Wheel/Gooseneck Custom Wiring Harness part…

view full answer...

Can You Use The 3rd Brake Light Logic Module With A 4-Pole

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching