Customers compare K71-633-2 to these similar products
Products Featured in this Video
Speaker 1: Today we're going to take a look at the Dexter e-coat, 10 inch hub and rotor disc brake kit, with the five on 4-1/2 inch bolt pattern, for 3,500 pound EZ Lube axles. Now these trailer brake assemblies will make it very easy to upgrade from drum brakes to disc brakes for better performance. Disc brakes'll give you more consistent stopping, even at highway speeds, dramatically… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
While we do have the disc brake hub and rotor for a 3,500 lb axle, we do not offer torsion axles, or any axles of the length you need. But for the hub and rotor brake kit that has a 5 on 4-1/2" bolt pattern and works with 14" wheels…
view full answer...The mounting brackets of the Kodiak kit like the #K2R526D and the Dexter kit part #K71-647-648 locate the caliper relative to the hub in a slightly different position as well as use different bolt hole dimensions. Because of this the two kits…
view full answer...For your Titan BrakeRite I Plug and Play Electric-Hydraulic Actuator Kit #T4813102 it sounds like you have bled the lines properly, but the power is definitely an issue. It sounds like you have a lack of power from your breakaway to your actuator as…
view full answer...According to Titan, if only the white and black wires are connected, the hydraulic pump should not run. With those two wires attached, the pump should start when the blue wire is touched to the positive battery terminal. The folks at Titan tell me…
view full answer...If your OEM controller on your 2006 Ford F-350 is a proportional controller, like the Prodigy P2 #90885, then it will likely only send power back through the pedal when you are actually moving. The P2 has an internal inertia sensor so that it…
view full answer...It sounds like the motor is running but not building pressure. This could indicate a leak somewhere since you have a full reservoir. The next thing you can do is bleed the brakes to ensure the system is free of air in the lines. I have included a…
view full answer...First, make sure that the adapter #T48456000, is wired into the input wires on the BrakeRite EHB. White to white and blue to blue. The adapter is simulating the load of brake magnets so that the brake controller thinks there are just electric brakes…
view full answer...The ends of brake hose #T0776500 are fixed and do not swivel. Normally on the components you are threading this onto one of them would have a swivel so you would thread the hose onto the fixed component first and then attach the end that threads onto…
view full answer...In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…
view full answer...Adding a front hitch to your 2017 Ford F-250 Diesel 4x4 Off Road will reduce your bumper clearance in the front by about 3 inches but if you have the air dam on the front, that will hang lower than the receiver. I recommend the Curt #C31078 over the…
view full answer...The steel tubing #T1086600 has 3/8"-24 threads. This is pretty much standard and it should fit just fine on your trailer. On the off chance that it doesn't fittings to adapt one to the other are readily available at any auto parts store.
view full answer...When selecting an LED light, if the description states it is waterproof or submersible then the light can be submersed in water. The item you selected, Waterproof, Under 80 Inch LED Trailer Light Kit with 25 Foot Wiring Harness, part #TLL9RK, has…
view full answer...