Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs
(179 reviews)
Price: $232.21
Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs
Retail:$483.22
Our Price: $232.21
You Save: $251.01
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
- All Info
- Reviews (179)
- Q & A (0)
- Photos
Fulton Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- Bolt-On
- Leveling Jacks
- Tongue Jacks
- 10 Inch Lift
- With Wheel
- Alloy Aluminum
- Fulton
Maintenance-free, corrosion-resistant jack is made for marine, recreational and utility trailers. Features aluminum alloy construction, adjustable mount and swivel system and wide-track wheels for superior stability.
Features:
- Adjustable mount and swivel system for easy lifting and transport
- Can be adjusted to any height for mounting
- Swivels into position simply with the integrated, easy-to-grip pull pin
- Maintenance-free construction
- Lubricated, 1-piece gearbox eliminates the need for manual lubrication
- Ventilation port allows you to add extra grease if desired
- Wide wheel base allows for increased stability
- Anodized finish on inner and outer aluminum alloy tubes prevents rust even in the harshest environment
- Sidewind handle is made of strong plastic for durability and ease of use
- Bolt-on installation
- Includes wheel stop
Specs:
- Application: fits 3" x 3" and 3" x 4" tongues
- Lift height: 10"
- Bracket range of adjustability: 8"
- Wheel diameter: 8"
- Wheel width: 3"
- Pull pin diameter: 9/16"
- Height from top of mounting bracket to the floor:
- Extended: 26-1/2"
- Retracted: 16-1/4"
- Height from bottom of mounting bracket to the floor:
- Extended: 21-1/2"
- Retracted: 11-1/2"
- Capacity: 1,600 lbs
- Lifetime limited warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
1413040134 Fulton F2 Marine and Recreational Jack for 3" x 3" and 3" x 4" Frames, Sidewind, Wide Track, 1,600 lbs
Item # F1413040134
Installation Details
California residents: click here
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
- Manufacturer issue
Customer Reviews
Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs - F1413040134
Average Customer Rating: 4.8 out of 5 stars (179 Customer Reviews)
Maintenance-free, corrosion-resistant jack is made for marine, recreational and utility trailers. Features aluminum alloy construction, adjustable mount and swivel system and wide-track wheels for superior stability.by: Thomas09/30/2023
Adjustable set up sold me. My driveway has a down slope. My truck is partially in street which has a slope which puts ball mount much lower then run height. I couldn’t swing old Jack up. This adjustable sliding mount is amazing. Heavy duty. Overkill for my boat well worth it. Mine was missing the wheel lock so I called E Trailer and they are sending me one.
by: Dave04/21/2017
Excellent so far. I bought this to replace the lower quality wheel jack that had been included on my aluma cargo trailer. The jack they included was OK for occasional use but had a small wheel and seas to really up to regular usage. My aluma trailer has been turned in to a custom home build travel trailer so the jack is getting a great deal of use in moving the trailer around while loaded. The tongue load on the trailer is around 350# so this jack is very much overkill. But I wanted the large wide wheel as ocasionally a travel trailer has to get moved in packed dirt or gravel.
I must say this jack is a wonderful upgrade. While expensive it has all the features I wanted. The wheel does not spin around while easing or lowering so you don't have to hold it with your foot. And the bracket is adjustable. You can loosen the tube on the pivot bracket and slide the jack adjusting the resting height and fully extended height. I set mine at the lowest point as I often was finding with my other jack that while camping I would have to dig a hole to get the jack folded down. So this one is 2 inches shorter at the lowest setting which should allow it to be deployed in more situations while camping where the tongue actually needs to be lower than the axle to level the trailer.
It's very well build. The wheel is large and wide. The jack feels very solid. The U-bolts made installation easy, although I added some steel pieces under the uboots to enlarge their contact area. The jack deploys easily. It cranks up and down easily.
Only surprise was the description says maintenance free. It is not. Inside the box there is a printed technical bulletin that explains how the acme screw needs to be regularly greased. And you do it through a vent hole which is hard to access. With all the quality they built in it seems like they would have taken the time to drill one more hole and install a grease fitting. I'll install one at some point. Greasing through the vent hole is a pain. You have to work the grease in with your pinky finger or something small.
But overall it's a wonderful upgrade. Add a grease fitting and it would be perfect.
by: Robert05/18/2018
This a heavy duty trailer jack. Easily attached to the trailer. Aluminum construction and a lock for the wheel.
by: Danny05/24/2019
Very good product. It was easy to install but the u-bolts had to be cut off to fit my 2” thick boat frame. Don’t make the mistake I did by ordering the 12” lift jack. The handle would not clear the boat keeping me from raising and lowering the jack.
by: Ralph11/13/2023
This is an AWESOME trailer jack. Unfortunately, I had to return because it was just too big for my utility trailer. I should have done more reading prior to ordering. It was missing the brake attachment but I have no doubt etrailer would have got me a replacement out quickly. I dealt with James R and he got me taken care of.
by: Donald07/29/2022
The F2 is an excellent trailer jack that I installed on a new CC boat trailer as the stock jack failed prematurely. My last two bass boats also required upgraded jacks. The Fulton replacements never require further attention. This unit is far easier to turn the jack handle, impressive hardware is included to quickly install, and absolutely worth the investment. Spend time fishing not fixing!
by: Ryan10/06/2023
The product is heavy duty and the large wheel makes it easy to move my boat around my barn. T h e wheel lock was missing but I called etrailer and they are sending a replacement.
by: Tommy S. 12/26/2016
Installed the jack with ease using the instructional video on e-trailers website. Very fast shipping at a reasonable price. This jack is a beast and makes all others look wimpy is a major upgrade from the 1000 lb. jack that was on my aluminum boat trailer the wide wheel also makes it easy to maneuver. Thanks
by: David P.07/24/2017
The Fulton trailer jack I bought from etrailer is excellent. Got it installed on my home built travel trailer tonight. I love how the wheel does not spin when it's raised and lowered. And the 8 inch wheel is so much better for moving the trailer around than the old small narrow wheel was. And I love that the jack can be adjusted up and down on the bracket. Often when camping I would have to dig a hole under my old jack to get it vertical. This jack is 2 inches shorter at the lowest setting so this should no longer be a problem.
by: Jake C05/23/2012
Overall this is an excellent Jack. Overkill for my small Rack n Roll Kayak Trailer. Box had a huge gash in it but contents were fine. Instructions were very detailed. I am a little disappointed that the Jack did not have a handle keeper on the main tube for some reason. Had to trim the U-bolts because the tube on the Kayak trailer is only 2"x2", but no big deal. Overall this jack is killer. I attached 4 photos of the install.
by: Ronald11/18/2022
It is robust, simple to assemble and install. The larger wheel will allow me to move the trailer more easily on grass or gravel.
by: Dona04/25/2016
I gave your jack to my husband for Christmas. Here is a picture of it on his iceboat trailer. He has been very pleased with your product.
I am also attaching a picture of his ice boat.
by: Spd04/18/2024
Service and advice was excellent
by: Brad 02/06/2024
Way better cranking up or down and easier to stow in the towing position.
by: Kevin01/17/2024
It took a little longer than I thought to receive it. On a high note, your customer service was excellent.
by: Jeff02/15/2020
Very poor design— bought this items because you can adjust the mounting bracket along the jack — the mounting bracket covers the bolt that needs to be loosened — I work on it ONE HOUR still not loosened — a regular socket wrench won’t fit —- just terrible—- a few people need to be fired for allowing this design ( now concerned about the overall quality if a basic design can’t be done right )
by: Robert08/10/2019
Great trailer jack only problem was the ubolts were too long and I had to cut them so the jack would swivel up
by: Al B09/18/2014
Replaced Trailer Jack on my FLOE snowmobile trailer. Two of the mounting holes lined up perfectly and I drilled and tapped the other two. Very easy installation. The trailer Jack operates very smoothly, of course it is new. I'm hoping after a couple Minnesota winters it stays smooth. The large, wide wheel rolls great on pavement and even allows me to move the tongue on gravel. It makes hitch alignment easier. I liked this one so much I just ordered another for my boat trailer. Thanks etrailer. Great service and delivery on the first one.
Al B.
9/18/2015
After a winter season where it was exposed to 2000 miles of slush and snow on northeastern Minnesota roads the jack is still operating as smoothly as the day it was installed.
by: John02/04/2022
The Fulton F 2 is a beast. Got it installed today on my Blackjack 225 . Very solid heavy duty and smooth operation. Of course the saltwater will be the real test. But it is sealed and should be good. E trailer got it delivered when they said and followed up with email updates as we had to wait for manufacturer to ship. But I didn’t have to guess or chase them.
by: Rhinehart12/16/2022
Outstanding service. Very fast and efficient. Even at holiday time, out order came very quickly. Thank you etrailer!!
by: Jeff 10/06/2023
Had what I needed and shipped super quick. Better price than any other!
by: Dennis 01/29/2023
A very easy install and looks great. It is much beefier than the original and a lot more solid. I should have done this long ago. Worth every penny and very fast shipping. I couldn’t ask for more. Thanks etrailer for your great service.
by: Frank 09/06/2023
Great customer service and quick shippi ng.
by: Robert12/26/2018
This was the only jack I could find that was adjustable to fit on the tongue of a 37 ton wood splitter that weighs 1200 Lbs. it was impossible for me to lift and lower the landing gear at the same time. the Fulton swing up jack made it possible to lift the tongue while engaging or disengaging the landing gear. also when engaging the landing gear I could swing up the jack so it would clear some room for a split log catcher that allowed me to install horizontally above the tongue. the jack laid horizontal along the tongue below the catcher. the jack holds the weight easily, only thing is with all that tongue weight the wheel does not swivel all that easy unless you are rolling the trailer forward or reverse. you have to toe kick the wheel in the direction you want it to roll from a stationary stop. In all this jack is awesome and very adjustable and strong.
25
179
Show More Reviews
See what our Experts say about this Fulton Trailer Jack
- Would Fulton F2 Bolt-On 1600 Pound Swivel Jack Fit a 1-1/2 x 3 Inch Trailer FrameYour trailer frame at 1.5 x 3 inches would be too small for jack # F1413040134. You would need to have a spacer welded to the trailer frame by a qualified professional to properly mount the jack. Since welding is going to be required it would be easier to just get a weld-on jack, # FTJ120W0301.
view full answer... - Will the Fulton F2 Trailer Jack # F1413040134 Work with a 2 Inch x 3 Inch FrameYou can install the Fulton F2 Jack, # F1413040134, on your trailer, but you will need to pick up smaller u-bolts. The u-bolts included with this jack fit 3 inch x 3 inch and 3 inch x 4 inch frames. You could pick up two of the CE Smith U-Bolts, # CE15252A. These u-bolts are 3 inches long x 3-1/8 inches wide. I tested it with the Fulton F2 Jack, # F1413040134, and they fit. The shorter length and longer threads should work well with your 2 inch wide frame.
view full answer... - Can I Use a Fulton F2 F1413040134 to Move my Trailer a Couple of FeetThis jack is going to be a great solution for your needs. The wheels are designed to help you move the trailer around to help get it hooked up to your vehicle. The wide 8" wheel is designed to make this easy be rolling over any small cracks or rocks that may be in the way. It is recommended that when moving your trailer that you have the jack retracted some you don't want to be pulling it around all of the way extended because you'll be putting a lot of stress on it. With your trailer...
view full answer...
- What Fulton Jack Can Mount to Welded-On Mounting PlateYou can use the Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs Item # F1413040134, which mounts to a weld-on plate # F500277. If this is the plate on your trailer you're all set; if not please give the mounting hole spacing from your plate so we can find a compatible jack for you.
view full answer... - Available Sizes of Trailer Jack Caster WheelsFor an industry-standard round tube jack the largest caster wheel we have is a 6-inch size made for a 2-inch trailer jack inner tube, like the Dutton-Lainson part # DL22539 you referenced. Most such caster wheels are rated for 1200-lbs. This and similar caster wheels for 2-inch jack tubes are shown on the linked page. We do not offer adapters or spacers to enable these to fit other tubing sizes. The other page displays all of our bolt-on jacks with wheels. We do have complete jacks with...
view full answer... - Recommended Maine Trailer Jack for a 2006 Mastercraft X-StarI have the perfect replacement trailer jack for your 2006 Mastercraft X-Star boat trailer. For this, I recommend using the Fulton F2 Swing-Up, Wide-Track Trailer Jack part # F1413050334. It has a 1,600 lb. capacity and can raise your boat trailer up to 8". As long as your trailer's tongue does not weigh more than 1,600 lbs. then this jack will work well for you. You will also want to use the Weld-On Mounting Bracket and Hardware for Fulton Swing-Up Trailer Jacks part # F500277 to use...
view full answer...
- Mounting the Fulton F2 Trailer JackThanks for the photo. The Fulton F2 jacks use a different mount so it isn't compatible with your current base. You will need to remove the base and then you can install the F2 # F1413040134 you referenced. This F2 will come with all new mounting hardware. If you want to keep your current mount, then I recommend the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - Black - 12" Lift - 1,500 lbs # F27CR which is the closest compatible option.
view full answer...
- Mounting Bracket Bolt Pattern of the Fulton F2 Trailer JackI spoke with my contact at Fulton and he informed me that the mounting flange of this Fulton F2 Swing-Up Trailer Jack # F1413040134 and all of the other F2 jacks has center to center bolt hole measurements of 3.44 inches by 4.44 inches. What that means is that you could install this jack on either trailer frame with either a 3 inch tall frame or a 4 inch tall frame if you were using U-bolts. You may also be interested in purchasing a Weld-On Mounting Bracket and Hardware # F500320 if...
view full answer... - Trailer Valet Jack Recommendation for Moving a Boat Trailer into a GarageI can't recommend you attempt to push a 3,700 lb trailer up a hill with the Fulton Jack part # F1413040134. You would want the part # STC-V211 for this as it has a handle that you can turn to power the wheel and has an emergency brake in case you needed to stop the trailer abruptly. The # F1413040134 will allow you to move a trailer around a little bit since it has wheel casters, but since it doesn't have a brake built into it and you plan to push the trailer uphill, I can't recommend...
view full answer... - What are the Mounting Hole Distances on the Fulton F2 Swing-Up Trailer Jack, # F1413040134I went out to the warehouse to measure the mounting plate on the Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs # F1413040134. The mounting holes are 3-1/2 inches (top to bottom) and 4-1/2 inches (left to right) apart on center.
view full answer... - What Is the Height of the Pro Series Snap-Ring Swivel Marine Jack From Mount to the GroundThe Pro Series Snap-Ring Swivel Marine Jack, # PSEJ10000101, mounting bracket measures 13 inches from frame to ground when the jack is retracted. When extended the measurement is 23 inches from the bracket to the ground. This distance will provide a 10 inch lift for this jack. The Fulton Jack # FXPD15L measures 12-3/4 inches from frame to ground. This Pro Series jack is actually a 1/4 inch taller. If you are needing a jack that has a shorter retracted height, the Fulton F2 Swing-Up Trailer...
view full answer... - Replacement Swivel Jack that is Held Onto its Mount with a Snap RingIt sounds like you have a swivel jack that attaches to its mounting plate using a sort of snap ring. We do have jacks like that. I recommend Fulton jack # FTJ120W0301. The great part about this jack is that if it doesn't fit the mount you have, it comes with a mount of its own that you could have a professional welded install. This jack is rated for 1,200 pounds. I have linked a video review of this jack for you.
view full answer... - Recommended Fulton F2 Trailer Jack to Replace Dutton Lainson Jack on TrailerThe Fulton F2 Swing-Up Trailer Jack with No Mounting Hardware # F1413100334 referenced in your question features a bolt pattern that is 3-3/8 inches on center x 4-3/8 inches on center. There is not a Fulton jack currently available that includes a mounting plate that matches the 3-1/2 inch x 3-1/2 inch pattern that you mentioned. To use this particular jack, you will just need to a new plate welded to the trailer like part # F500277. Another option is the weld on Fulton F2 Swing-Up Trailer...
view full answer... - Replacement Parts for Fulton F2 Swing-up Swivel Trailer JackThe Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs # F1413040134 or weld on version # F1413050334 are both available as complete units but there is not a replacement part available for what you are showing in the picture from the manufacturer. The manufacturer currently only offers the following parts as replacements for the F2: Replacement Pull Pin Kit for Fulton F2 Swing-Up Jacks # F500136 Replacement Wide-Track Wheel for Fulton F2 Swing-Up...
view full answer...
- Fulton F2 Wide Wheel Jack Compatibile 2000 Ranger R83 Ranger Trail Single Axle TrailerIt doesn't look like your bolt spacing will work for the F2 jacks. The Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs # F1413040134 is designed to work on either 3"x3" or 3"x4" tongues inch trailer frames. It won't fit the current mounting locations but it will fit your trailer frame if it has that dimension. The distance between the mounting holes measure exactly 3.44 center to center and 4.44 center to center, which in the closest fractional...
view full answer...
- Replacement Pull Pin Kit and Housing For Fulton F2 Trailer JackWe do have the Replacement Pull Pin Kit # F500136 which is the part number 18 in the photo you found. We do not carry the part number 4 for the Fulton F2 Trailer Jack # F1413040134 at this time so you may need to replace the parts from another damaged jack if your part is not repairable.
view full answer...
- What is Axle Diameter of Fulton F2 Trailer Jack F1413040134Hey Loren, the axle of the wheel that comes on the Fulton F2 trailer jack part # F1413040134 that you referenced is 1/2 inch in diameter. We have a replacement wheel for this with the part # F500131.
view full answer... - How to Choose a Replacement Jack for a 1991 Four Winns TrailerWhen choosing a jack, you will want to choose a jack that can support the tongue weight of your trailer and a jack that has an appropriate lift height for your trailer. Typically, the tongue weight on boat trailers does not exceed 15 percent of the gross trailer weight. Be sure you verify the tongue weight capacity of your trailer before selecting a jack. If you still have your old jack, you can go by the weight capacity and lift height of that jack to choose a replacement jack. The...
view full answer... - Is There a Swivel Jack That Has a Handle Catch To Keep Handle Up During TravelI spoke with my contact at Fulton and he informed me that both the Fulton XLT Jack # F141133 and Fulton F2 Jacks, like # F1413040134, have a handle catch to help keep the jack handle from swinging when the jack is stowed. For a Fulton jack, I recommend the Fulton XLT Swivel Trailer Jack # F141133. The XLT offers a 12 inch lift, measuring 15 inches when retracted and 27 inches when extended. This jack has a lift capacity of 1,500 pounds. The acme screw raises and lowers the jack quickly,...
view full answer...
- Weld On Plate Recommendation for Installing Fulton F2 Jack Designed for Bolting OnIf you have a Fulton F2 jack part # F1413040134 like what you referenced the plate part # F500277 will work perfectly with it. This plate is designed specifically to work with the F2 jack so you wouldn't have to measure anything to verify it's compatibility.
view full answer...
- Recommended Replacement Bolt Thru Jack Similar To Fulton F2The Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12" Lift - 1,500 lbs # FXPD15L would be a great option. This jack is similar to the F2 you mentioned. The Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs # F1413040134 has a different style of swivel that is integrated into the design like all of the F2 models. It attaches to the trailer using hardware that is included with the jack.
view full answer... - Dimensions of Fulton F2 Jack F1413040134The Fulton F2 Swing-Up Trailer Jack # F1413040134 has a moveable mounting bracket that provides an adjustment range of 8-inches. The height from bottom of mounting bracket to the floor is Extended: 21-1/2" and Retracted: 11-1/2". Check out the review video for more helpful information and measurements.
view full answer...
- Bolt-On Side-Mount Swivel Jacks for Boat TrailerIf you want to avoid the hassle of trying to match up a new jack to the old mount on your trailer you can simply bolt on a new side-mount swivel jack like the Fulton F2 # F1413040134. The swiveling F2 fits 3 x 3 and 3 x 4 trailer tongues, features rust-free aluminum construction, has a sturdy 3-inch wide wheel and includes a wheel stop. It is rated for 1600-lbs. This and all other bolt-on swivel jacks are shown on the linked page. If you wish you can send along photos of your jack and...
view full answer... - Recommended Replacement Bolt-On Jack For Boat TrailerI do not have a Jack that exactly fits your trailer frame dimensions. However, a close match that should work is the Fulton F2 Swing-Up, Wide-Track Trailer Jack, 8" Single Wheel, Sidewind, Bolt-On - 1,600 lbs # F1413040134. It has hardware for 3 inch x 3 inch and 3 inch x 4 inch trailer tongues. If the included u-bolts do not secure the Jack to your trailer frame, then you could get different sized u-bolts that do (we do not have any smaller selections). This Fulton Jack is an adjustable...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Lori W
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Dustin K
Updated by:
Laura H
Updated by:
Lisa S
Updated by:
Shelly K
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Mike S
Updated by:
Carrie F
Installed by:
Cole B
Installed by:
Steven C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Tyler M.
2/20/2020
I went out to our warehouse to look into this jack personally. In order to reach the bolt, you have to rotate the mounting plate 180 degrees by pulling on the pull pin. The pull pin will auto-lock every 90 degrees. Once the mounting place is rotated, so that the U shaped cutout lines up with the bolt, you will be able to access the bolt. You will also want a socket extension with a 3/4 inch socket in order to loosen the bolt.