Recommended Maine Trailer Jack for a 2006 Mastercraft X-Star

Question

Question:

please provide details of the drop leg jack as well as a U bolt on style of F2.

asked by: David B

0

Expert Reply:

I have the perfect replacement trailer jack for your 2006 Mastercraft X-Star boat trailer. For this, I recommend using the Fulton F2 Swing-Up, Wide-Track Trailer Jack part # F1413050334.

It has a 1,600 lb. capacity and can raise your boat trailer up to 8". As long as your trailer's tongue does not weigh more than 1,600 lbs. then this jack will work well for you. You will also want to use the Weld-On Mounting Bracket and Hardware for Fulton Swing-Up Trailer Jacks part # F500277 to use this jack with your existing mounting bracket.

expert reply by: Conner L

0

click to enlarge

David

8/16/2017

please provide details of the drop leg jack as well as a U bolt on style of F2.

Reply

Conner L.

8/16/2017

For a drop leg jack, I recommend using the Fulton Square Fixed-Mount Marine Jack part # FHD2500. This jack is ideal for marine and recreational use. It has a 2,500 lb. weight capacity and can be extended up to 35-1/2" using the drop leg feature and will bolt around a trailer frame up to 3 inches wide by 5 inches tall. For a bolt on jack, I recommend using the Fulton F2 Swing-Up Trailer Jack part # F1413020134. This jack is rated for use with a tongue weight up to 1,600 lbs. It can provide up to 10" of lift and fits trailer frames 3"x3" and 3"x4". The dual wheel feature will allow you to easily maneuver the trailer. I have included a review video of each jack for you.

Reply

Answer 1

The Dexter DX7.5L A-60 Brake Actuator part #DX89FR for disc or part #DX33FR for drum will work to replace the surge coupler of your Mastercraft boat trailer. I looked up your trailer and was not able to determine if it had disc or drum brakes which…

view full answer...

Answer 2

For your application I recommend using the Titan Actuator #T63FR if you have drum brakes or the Dexter DX7.5 #099-175-20 if you have disc brakes. These are rated for 7,500 lbs and fit a 2" hitch ball which should match up just fine for your 2007…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 10

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...