Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Vehicle End

See what our Experts say about this Hopkins Trailer Wiring

• Solution for Connecting RV 4-Flat Male to 4-Flat Male on Tow Dolly
  I do have a solution for you, however we do not have any adapters available that will allow you to connect the two male 4-flat connectors on your RV and tow dolly. An RV or vehicle will typically have a 4-flat female connector at the rear for hook up with the trailer. I recommend simply cutting the male connector from the RV and replacing it with the Vehicle End Hopkins Endurance Quick-Fix Replacement 4-Way Flat # HM48190. After cutting off the RV's male connector, you will simply insert...
  view full answer...
• Why Do Test LEDs Light Up Without Actual Trailer Lighting Signals Transmitted
  LED type lights are very highly efficient, using only about 1/10th the power required by standard incandescent light bulbs. This means that certain wiring harnesses will cause one or more of the LEDs to light up just from the very low-level residual power that "leaks" through a harness even when there are no full-scale signals being transmitted. This is entirely normal and does not indicate any malfunction in part # HM48190. If you have a voltmeter you can test each of the three circuit...
  view full answer...
• Availability of Hopkins Endurance Quick-Fix Replacement 4-Way For Vehicle
  What you're looking for is the # HM48190. This is the same as the # HM48192 but with the vehicle end connector.
  view full answer...
• How To Replace a 4-Way Trailer Connector Without Standard Wire Colors
  In order to replace a 4-way trailer connector you can use part # HM48192 for the trailer end or part # HM48190 for the vehicle end. These connectors both have built-in lights to help with troubleshooting. In regards to installation; the usual wire colors are green for right stop/turn, yellow for left stop/turn, brown for running, and white for ground. If you have different colors which is the case you will unfortunately have to test each wire for function by touching the wire lead directly...
  view full answer...
• Replacement 4-Way Connectors to Replace Damaged Connectors
  We sell replacement 4-way connectors like the part # HM48192 for the trailer end side or the part # HM48190 for the vehicle end side. You'd just need to cut off your damaged 4-way and wire in either connector to it. These also have circuit testers built in for each circuit as well.
  view full answer...
• Adapter Harness to Convert Tekonsha/Hopkins Male Plug to Female Plug
  It sounds like you're trying to convert one of the male ends to female. If that is correct you need an adapter with female on both ends so you can use the the # HM48035 and add the # HM48190 to the other end. There are no premade adapters so this is the simplest solution. You could also cut off one of the male ends you and add the # HM48190 so you have less parts to purchase.
  view full answer...
• How To Mount Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Light
  You do not need a mounting bracket with the Quick-Fix Connector # HM48190 as it comes with mounting holes that you can use. A mounting bracket would only cover the LED lights that allow you to confirm that the wiring circuits on your 2007 Ford Explorer are working properly. It is best to mount it somewhere that you can easily access and will be able to see the LED lights to check operation at the connector. The Hopkins Fold-Over Mounting Bracket # HM48595 will not fit over the Hopkins...
  view full answer...
• Availability of Hopkins Quick Fix Replacement 4-Way for both Trailer and Vehicle Side
  Hey Guenther, we have both sides of the Hopkins Quick Fix Replacement 4-Way ends with the part # HM48190 for the vehicle side and the part # HM48192 for the trailer side.
  view full answer...
• Low Voltage on Factory 4-Way Trailer Connector on a 2002 Toyota Tundra
  If the factory tow package wiring on your 2002 Toyota Tundra uses both fuses and relays then the issue could be a faulty relay. They can sometimes still allow some power to trickle back even if they are bad so that is one thing to check. There could also be a corrosion issue, ground problem, or wiring problem. If you are testing the pins on the 4-Way go ahead and test one of the wires going to the connector instead. If you get the proper voltage on the wire but not the pin then it is...
  view full answer...
• Can a Reese Multi Tow 7-Way and 4-Pole Trailer Connector be Repaired if 4-Pin Connector Broke
  You can purchase a separate 4-pin connector like # HM48190 but it won't fit the slide slot on the mounting bracket on the multi-tow 7-way and 4-pole trailer connector # 74682. You can zip tie it or even let it hang if you prefer. I included a couple video reviews for you too.
  view full answer...
• Recommended 4-Way Flat Connection For Kayak Trailer And Vehicle
  To fix the 4 way connections you cut off, I recommend the Quick Fix 4 Pole Flat Car and Trailer Ends # 48195. If you want to add the LED test lights so you know your vehicle side is working, you can use the Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Vehicle End # HM48190. The 5th wire on the trailer side will need to be doubled up. This extra wire is a running light duplicate that often is added so a jumper wire is not needed from one side...
  view full answer...
  
• Is the Terminal Grease Included with the Hopkins Connector Part # HM48190 Conductive
  The terminal grease that is included with the Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector part # HM48190 is non-conductive therefore you should not have any issues using it on the quick-splice terminals of the trailer connector. The grease as you mentioned is designed to keep out dirt and moisture therefore is highly recommended that you use accordingly. If you need more of the terminal grease for other applications then you can use part # 11755.
  view full answer...
• How To Tow Trailer with 4-Way Using Motorhome with 6-Square Trailer Connector
  In order to tow a trailer with 4-flat using a motorhome with 6-square, you can either make an adapter for the motorhome or you can simply wire on a 6-way to the trailer. There isn't a pre-built adapter for this but you'll need the 6-Pole Square Trailer Wiring Connector Kit part # 37995 regardless of which of the above two options you choose. However, if going with the latter then you'll also need the Vehicle Side 4-Way part # HM48190. This option would not require any splicing into the...
  view full answer...
• Adding a Removable 4 and 7-Way Trailer Connector on a 2005 jeep Wrangler Rubicon
  What you can do is replace the trailer wiring set up you have on your Jeep and hardwire in # HM40975-11998. This will allow you to just unplug the connector part. The wire functions and colors on this harness are a little different. Since the 7-Way part of the connector is hardwired on your Jeep, replacing the whole connector is the best way to go. On your current set up you should have a white, brown, yellow, and green on the 4-Way, and then a black, blue, purple, and white on the 7-Way...
  view full answer...
• Converting Vehicle Side 7-Way Trailer Wiring to 4-Way Standard Wiring
  It sounds like you want to do a conversion from your 7-way to a standard 4-way trailer connection that has the 3 functions and ground. There are a couple different options for you that don't require much if you just need the 4-way connector for a trailer. You can use the Pollak 7 Pole to 4 Way Connector Adapter # PK12716 for the easiest connection. Your 2001 Xterra didn't come with a factory 7-way so you may find there is a 4-way plug connection behind your 7-way that you can simply...
  view full answer...
  
• 4-Way Vehicle Side Trailer Connector that Can be Spliced Into Wires from Trailer Wiring Harness
  I have a great option for you. Take a look at the Hopkins Quick Fix connector # HM48190. All you have to do is remove the screws on this connector, place the wires in the correct locations, and then put the cover and screws back on. The white wire will go to the one exposed pin. Next to it will be the brown wire, then the yellow wire, and the green wire is last. This connector also has a handy LED test light feature so you can see if each function has power without using a meter or circuit...
  view full answer...
• Are Wesbar Coiled 4-Pole Connector 54000-026 and Hopkins Quick-Fix Connector HM48190 Compatible
  Yes, the parts you referenced, Wesbar coiled trailer-end 4-pole with pigtail leads # 54000-026 and Hopkins Quick-Fix Replacement 4-Way Flat Vehicle Connector # HM48190 are compatible. These two parts will give you a coiled 4-pole extension with both vehicle-side and trailer-side 4-pole connectors, with LED test lights on the vehicle side plug.
  view full answer...
• Can New 4-Way be Spliced Onto Trailer Wiring Harness 118566 on 2015 Ford Escape
  Yes, you can splice in a new 4-Way flat vehicle end, such as # HM48190. This vehicle-side 4-Way also has LED test lights so its easy to determine if one of the circuits isn't working. Or for a regular short-length harness you can use # 18252.
  view full answer...
• Adapter to Go from 6-Way Square on Tow Vehicle to 4-Way Flat Trailer Side Connector
  It sound like you want the opposite of adapter # 30104. That would mean your tow vehicle has a 6-Way square connector. What you can do is use # 37995 which has both the vehicle end and trailer ends. On the trailer end, you can wire the loose wires to a vehicle side 4-Way, # HM48190. Then you will have a 6-Way square to 4-Way flat adapter. The other option is to just replace the 4-Way flat on the trailer with the trailer end 6-Way that comes with # 37995.
  view full answer...
• Trailer Wiring Harness with 4-Way Flat Connector for 1997 Honda Valkyrie
  First, with LED lights, the color of the bulb needs to match the color of the lens. Otherwise you will have dim lights or off-color lights. If you want you can replace just the 4-Way end on the harness that you have with # HM48190. If you want to replace the whole harness I recommend going with a powered option such as # 119250KIT which will get the power for the trailer lights directly from the battery instead of drawing it through the tail light wiring.
  view full answer...
• Is There a Coiled 4-Way To 4-Way Extension Available?
  The Wesbar Trailer End Connector - 4-Flat - Coiled # 54000-026 will work to connect a 4-way plug like # HM48190 to the pigtail end to create exactly what you are seeking. Otherwise, we have options like the Hopkins Endurance Easy-Pull 4-Flat Extension w/ 2 Grip Rings - Vehicle and Trailer Ends - 48" # HM47114 to span that distance without the coiled wire.
  view full answer...
• Where to Attach the 12 Volt Power Circuit for 7-Way Wiring on a 2006 Jeep Rubicon
  For the 12 volt accessory circuit of the 7-way you plan on installing on your 2006 Jeep Rubicon you will want to run that all the way to the positive side of the vehicle battery through a 40 amp circuit breaker like part # 9510. 10 gauge wire should be used. If you are looking for a keyed power source that only sees voltage with the key on you will need to also install a part # PK5231201 inline with the 12 volt power circuit from the battery with a keyed power source run to the middle...
  view full answer...
  
• How Can I Determine If My 2023 Toyota Highlander LE Has The Factory Tow Package Or Not?
  The only way to really know if your 2023 Toyota Highlander LE has the factory tow package or not is to contact your local Toyota dealer with your VIN. They can tell you exactly what features your vehicle came with. Vehicles with the factory tow package would have the connector right behind the bumper like you described. So based on that, it sounds like you do have the tow package. We still recommend having a dealership run your VIN to be sure. If you do have the tow package, we suggest...
  view full answer...
• 4-Way Round Trailer Connection Much Smaller Than What I Can Find
  I have never seen a connection like that for a 4-way. Regardless of the pin size the slot is internal to the plug on the connection point instead of external as on current 4-Pole Round Connector # PK11404. I recommend replacing the connection with a standard size round connector # PK11404 or converting to the more common 4-flat # HM48190. The Adapter 4 Round to 4 Flat # will use the standard 4 round size connector.
  view full answer...
  

Do you have a question about this Trailer Wiring?