Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Corrosion-resistant ball mount is 9-3/8" long and fits 1-1/4" x 1-1/4" trailer hitch receivers.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we'll be reviewing part number C45026. This is the Curt Class-I Draw Bar made from a sturdy steel construction. It has a black gloss powder coat finish so it is going to stand up well against rust and corrosion. This mount goes through a high-quality manufacturing process, a CNC machine for consistent cuts and welds and it goes through a 7-stage washing method to help deliver a nice clean, smooth surface. Both the drop and rise positions are available to help ensure a more level tow. You see here that it does have a hollow shank here on the back side. When choosing a hitch ball, you want to make sure that shank of the hitch ball does not exceed the ball hole diameter which, for this mount, is going to measure right at 3/4". This is the portion here that's going to slide into the receiver tube of the hitch.
This is the shank of the mount. What you'd do is you'd slide this portion in, line up your pin holes and then, you're going to need a hitch pin and clip or a hitch pin and lock. These items are sold separately. You can refer to the Mounts product page in the Related Items to view those products or you can go to our website and type in part number PC2 and it will refer you to this 1/2" pin that comes with a clip. When it's installed in this position, this would be the drop position. We from the inside top edge of the receiver tube to the ball platform.
It's going to give us a drop of 3 1/4". When installed in the rise position doing that same measurement, it's going to us a maximum rise of 2 5/8". The distance from the center of the hitch pin hole to the back of this portion here is going to measure about 6". The distance from the center of the hitch pin hole to the back of the shank is going to measure 1 1/2". The distance from the center of the hitch pin hole to the center of our ball hole is going to measure 9 3/8". This mount is going to provide us with a tongue-weight capacity of 200 pounds and a gross trailer weight capacity of 2,000 pounds.
Because of the weight rating, it is classified as a Class-I draw bar. Here at the front, our draw bar thickness is going to be 3/4". Actually, it's just going to measure right over 1/2" at about 5/8" and about 2" in width. That's going to complete today's review of part number C45026. This is the Curt Class-I Draw Bar rated at 2,000 pounds. .
Average Customer Rating: 4.8 out of 5 stars (1996 Customer Reviews)
Corrosion-resistant ball mount is 9-3/8" long and fits 1-1/4" x 1-1/4" trailer hitch receivers.The product was priced very competitive with other vendors,the quality is great, and the shipping time was better than the other vendors. Thank you I will be doing more business with etrailer when the time comes.
Drawbar was delivered quickly, however, I did not know it required a smaller pin, so, fortunately, I had time to get that ordered before my trip.
I'm very glad to have gotten this hitch, in the year I've had it it's allowed me to trailer motorcycles twice and move myself, saving terrific money over renting a truck. I only wish I had ordered it sooner.
Installation wasn't terribly difficult, though breaking loose the bolts where the hitch installs would likely have been quite unpleasant if I didn't have an 18" wrench handle.
Very beefy, good quality ball mount. It worked perfectly with my curt hitch for my acura Tl. I tow a harborfreight folding trailer and never have an issue.
Excellent- I bought it to get More length from the vehicle without using a extender(which lowers by 50% your weight limits). It fits the bill perfectly and will tow a 400 Pound Sea Doo Spark with my Chevy Spark which has the E trailer hitch . Great service and speedy delivery!!
I would have rated this product as very good, but it would not fit into my 1.25 inch receiver. It was necessary to grind it down a bit and then repaint it. My other ball mount fit in the same receiver with no modification.
Simple, solid, effective. I needed a longer bar for our hitch in order to clear the back bumper of our 2000 Subaru Outback. This is perfect.
While visiting family in Brooklyn, N.Y. my trailer hitch was stolen. What can you expect it was Crookland, oops I mean Brooklyn. This was an exact replacement. Fast service, nothing bad to say all is good except my feelings for Brooklyn.
My go-to trailer hitch stuff place! Always good prices and easy ordering. "Chelsey" was a great help in selecting the best ball receiver.
Solid product, meets all specs. Hollow shank made it easy to install anti-rattle device.
You guys did everything you should have. The mount works great. It was the strangest UPS delivery ever-- thank God for thePost Office. I will happily buy from you again
Worked Great!
Works great.
That was what i was looking for and it arived on time Thanks
Arrived on time. Just what I ordered
parts good , shipping box was all but destroyed. Fits my chev. cavalier just great
Fit and finish are good.
Job well done. Thank you
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
This 13" drawbar keeps the tailgate off the trailer jack.
Being that long also keeps it I storage immediately after I disconnect the trailer.
No need for a locking pin.
Be sure to test fit your rig before trip day. Had to increase the safety chain length with this new ball mount. Not a big deal, but glad I caught it early!
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Maurice
8/14/2023
I have not had any problems with it yet.