Recommended Scissor Jacks To Stabilize Winnebago View Sprinter
Question:
How many do I need, 2 or 4, and where exactly do they go on the Sprinter frame? Do you have a picture of the installed spots? Thanks! The recommended scissors jacks, not the single leg thingie.
asked by: Curt
Expert Reply:
To stabilize your Winnebago View Sprinter frame I recommend using scissor jacks like part # JSC-24-IND on the rear corners of your Sprinter. I recommend using 2 jacks. This jack can be bolted or welded when installing. Welding should be done by a certified professional.
I recommend these over the # TJ01RT you came from because they have a much higher support capacity. The # TJ01RT has a support capacity of 1000 lbs versus the # JSC-24-IND that has a capacity of 5000 lbs.
The # JSC-24-IND scissor jacks can be adjusted from 4 to 24 inches. This also requires the crank handle, part # JCH-1 which is sold separately.
You can also use the power drill adapter, part # UF48-979005 that makes raising and lowering the jacks much easier. This adapter fits 3/8 inch drills.
Products Referenced in This Question
Crank Handle for Stromberg Carlson Scissor Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- Stromberg Carlson
more information >
Leveling Scissor Jack - 24" Lift - 5,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Pop Up Camper
- RV Motorhome
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 4001 - 5000 lbs
- Scissor Jack
- 24 Inch Lift
- Bolt-On
- Weld-On
- 1 Jack
- Stromberg Carlson
more information >
Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Tools
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 0 - 1000 lbs
- Drop Down Jack
- Bolt-On
- Weld-On
- 1 Jack
- etrailer
more information >
Continue Researching
- Q&A: Installation Information for the Replacement Cables for Enclosed Trailer Ramp Spring # ERS160D96
- Article: Most Popular Wheel Bearings
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How Does the Domar Stabilizer Jack Operate
- Q&A: Correct Replacement Parts for a Ventline VD0434 Roof Vent
- Q&A: Recommended Tow Bar Wiring Kit For Flat Towing A 2024 Jeep Wrangler With ParkSense
- Q&A: Can 3,500 lb Axle Trailer Leaf Spring 25-1/4 inch get Replaced with 5k Rated Spring
- Article: Trailer Wiring Diagrams
- Q&A: Is Roadmaster Universal Hy-Power Diode Kit the Correct Flat Tow Wiring for a 2024 Jeep Wrangler
- Q&A: Can I Upgrade My 3,500 lb Leaf Springs To 5,000 lb Springs If The Measurements Match?
- Article: Where to Position the Trailer Axle?
- Article: Don't Break Your Pipes or Your Wallet: Winterize and De-Winterize Your RV
- Article: Determining Trailer Tongue Weight
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)