Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs
(173 reviews)
Price: $185.29
In Stock
Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs
Item # 23-465
Our Price: $185.29
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (173)
- Q & A (0)
- Photos
Dexter Accessories and Parts - 23-465
- Trailer Brakes
- Electric Drum Brakes
- Brake Assembly
- 12 x 2 Inch Drum
- Dexter
- RH
- 7000 lbs
- Self Adjust
12" x 2" Passenger's-side electric trailer brake assembly fits 7,000-lb axles. Mounting flange has a 5-bolt pattern. Nev-R-Adjust brakes require little maintenance. Fits 14-1/2" to 16-1/2" wheels.
Features:
- Electric brakes are easier to install and offer more user control than hydraulic brakes
- Requires only an electric brake controller (sold separately) - no actuator or hydraulic lines necessary
- Nev-R-Adjust brakes automatically adjust to deliver optimum performance and braking power
- No need for manual brake adjustments
- Proper adjustment leads to better brake efficiency and less wear on your tow vehicle's brakes
- Adjuster plugs (included) cover access holes to keep dirt and grime out of the assemblies and off of the shoes
- Mounting bolts and hardware included
- Made in the USA
Specs:
- Application: most standard hub-and-drum assemblies, including Dexter, Lippert (LCI), and AL-KO
- Configuration: right hand (passenger's side)
- Dimensions: 12" diameter x 2" wide
- Mounting flange bolt pattern: 5 bolt
- Wheel size: 14-1/2", 15", 16" and 16-1/2"
- Axle rating: 7,000 lbs
- 5-Year limited warranty
K23-465-00 Dexter 12" Nev-R-Adjust Electric Brake Assembly for 7K Axles - RH
Replaces 23-465
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Product did not meet expectations
- etrailer mistake
- Wrong item was ordered
Customer Reviews
Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs - 23-465
Average Customer Rating: 4.8 out of 5 stars (173 Customer Reviews)
12" x 2" Passenger's-side electric trailer brake assembly fits 7,000-lb axles. Mounting flange has a 5-bolt pattern. Nev-R-Adjust brakes require little maintenance. Fits 14-1/2" to 16-1/2" wheels.by: Sidney11/28/2022
I have had this item installed for approximately one year on our 42 foot, 18,000 pound 5th wheel. It was easy to install and set up and has worked flawlessly ever since. We have put over 6,000 miles on the 5th wheel since the installation. I will definitely buy again if the need arises.
by: John 06/23/2023
OEM Dexter parts well worth the cost. Brakes are very important in the scenarios I use my trailer. You definitely feel 6 brand new brake setups behind you! etrailer kept me well informed through the process on order status. Shipping was quick. Will be shipping etrailer for any of my trailer stuff going forward.
by: Lisa11/25/2023
Quinn did sn excellent job on my order We compared pricing and informed me as to del8very times, I received email updates and was informed as to when to expect delivery. Oustanding and professional customer service, Highly recommend etrailer your trailer needs.
by: Mike A05/09/2019
One is what I had and the second is etrailer. All I ordered arrived in good shape. Everything fit perfectly. I will definitely use etrailer again soon!!
Thanks
Mike A.
5/10/2020
Great. Product as advertised. Fit perfectly. Always use etrailer. Thanks again.
by: Marty B08/03/2018
Order was received timely. I had questions regarding a possible design change going from two spring to single spring. I contacted customer service and they replied swiftly. Not being sure of the answer the customer service rep. Conner contacted the manufacturer to determine proper answer. All is good , apparently Dexter has changed from 2 spring to single spring at the top. The attached pictures show what I am referring to. Look at the wiring in the faulty picture. Of course pulling the hub was my last thing I looked at. Hence why I was getting a ground short and no brakes.
etrailer customer service get A+++
by: Arizona Slim05/08/2017
I had the brake lining shatter off of one of the shoes. This happened within the first 100 miles after putting the new brakes on. Tore the drum up beyond repair. Working on getting the brakes replaced under warranty but I had to ship them the parts back first. Trailer is up on blocks until then.
by: Robert03/31/2023
Love the dexter brakes, however their packaging is inadequate. Out of the 4 brake assemblies I bought 2 of them were partially disassembled.
Jenny N.
4/3/2023
Oh no! Customer Service will be in touch to assist you.
by: William08/30/2018
Product was an exact fit. Much easier than fighting springs and hold downs even with the right tools. It took about 45 min. per wheel start to finish. Etrailer was very helpful when ordering parts.
by: Chris O12/16/2016
Ordered lots of parts on Monday, received most of them by Thursday. The received parts were well packaged and undamaged. A few of the parts they didn't have in stock so they had those drop-shipped to me which should be delivered in the next couple of days.
No supplier I have ordered any parts from has such a great technical reference web site or personal customer support. Yea, Rebecca - Well Done! Yes, I'm very happy with the pricing.
Thanks for your great support and I look forward to doing business with them again. More info to follow as soon as I can get the parts installed on my trailer.
by: John08/14/2023
Exact replacement and easy to install.
by: Thomas 09/28/2021
I needed an order change and paula took care of everything even shipping came day early so i could get trailer reinspected. Will be my only place to order trailer parts ETRAILER
Thomas G.
10/1/2022
Very well Etrailer came thru with the parts ias in dire need of in a timely manner. I needed brake assembliies and drums for my 5th wheel Etrailer researched and very quickly got me the needed parts Not all parts were Dexter but that was expained to me. And the substitues worked very well. I will be a returning customer for sure ss they were very helpful while ordering and thru checkout.
by: Ben07/16/2023
Excellent product, exact replacement. Great customer service from etrailer, and product was delivered 3 days early. Thanks.
by: Ed Wagner07/15/2021
Christina J thanks for all your help the brake assembly was delivered extremely quick and installed easily!
by: Steve03/03/2018
I was worried about putting brakes back together, this is an easy repair with only 5 nuts to put on and rewire. Information on getting the right or left brake was very good and made this an easy project.
Steve
3/3/2019
Great, very happy
by: Glen09/07/2022
You didn't have the brake assembly I wanted but had the 7k at a higher price. Was told there was no difference between the two. I bought the 7K but would like to know if there is no difference, why I was charged the higher price. I needed one so I didn't have much choice. Not Happy. I'll think twice and think again before purchasing from etrailer again.
by: Brad07/08/2019
Product installed easily. Much more efficient than replacing the parts I would have needed and less costly. Part used on a Dexter 7000 lb RV axle.
Brad
7/9/2020
Working well, as it should but it is on a 5th wheel and doesnt have s lot of moles on it.
by: Ron W03/11/2020
I had a dragging brake. When I disassembled, found bottom adjuster was dislodged and unattached spring. Magnet was very much melted. I reassembled the brake assembly good enough to travel to final designation. I ordered this brake assembly, p/N 23-465 for passenger side forward axle and it fit perfectly. I've driven approximately 3,000 miles since repair without issue. I highly recommend this product and company
by: Jerry R10/10/2016
Excellent customer service and the brake units work great!
Jerry R.
10/10/2017
I traded last summer for a new one but the brakes worked just fine.
by: Rob 09/27/2022
Worked well to replace grease covered shoes and magnet. Lower cost than replacing individual components.
by: Ben W.10/23/2014
eTrailer shipped the product the same day and I received these assemblies 2 days later. Great service!
Very easy product to install. Looking forward to getting my trailer on the road and test them out. Keep in mind you'll need to purchase the plugs for the backplate as the old ones usually are bridle and probably won't seal out the elements.
by: PeteM57411/09/2022
Easy to install. I have taken several trips since then. I would buy this product again from etrailer!
by: Arizona Slim03/28/2017
Replacement for 6000 lbs. original equipment brakes. Hoping for more stopping power as I usually tow near the limit of the trailer.
Installation was easy and straight-forward.
First impression is not much different but of course new brakes need to be burnished. The effectiveness is sure to increase. Overall happy :)
by: Curt G.04/27/2017
Great price for a complete brake replacement. Way easier and not much more than just replacing the shoes. I upgraded from the 6000# that were on my fifth wheel to these 7000# ones. Also like the self adjusting feature.
by: Donald02/17/2019
I discovered my brakes on the right side of my trailer were not working by feeling the drums after driving just 2 miles. They were cold, other side hot. Took apart and found no adjusters on ether wheel. Just part of adjuster spring on one wheel. Magnets were warn. So I just replaced the whole brake plate, cheeped and faster. They work great now. This I believe was caused by a blowout.
by: Peter L.02/08/2017
Bought four complete brake assemblies
Delivery was prompt , well packaged
Once installed they worked as described
E- trailer keeps the several trailers we own on the road and operating safely
25
173
Show More Reviews
See what our Experts say about this Dexter Accessories and Parts
- Info Needed to Find Self Adjusting Trailer BrakesThe Dexter Nev-r-Adjust assembly part # 23-464 is a self-adjusting 12 inch by 2 inch assembly for a 7,000 lb axle that has a matching right side of # 23-465. If your trailer has a different size/capacity need let me know what that info is and I will set you up with the parts you are in need of. I attached an install video for the assemblies mentioned as well.
view full answer... - Hub/Drum Recommendation to Fit Timbren Axle Less Kit # ASR35HDS02For a hub/drum that does fit the Timbren Axle Less System part # ASR35HDS02 the part # 8-201-9UC3-EZ is the recommended hub. The hub/drum you mentioned will not fit on this spindle. The only hubs that will fit the # ASR35HDS02 have 6 and 8 lug configurations. For brake assemblies then you'd want the part # 23-465 for the right hand side or part # 23-464 for the left hand side.
view full answer... - Dexter Nev-R-Adjust 6K and 7K Electric Brake AssemblyThe Nev-R-Adjust Electric Brake Assembly for 6K pound axles # 23-459, # 23-458 and the brake assembly for the 7K pound axles # 23-464, # 23-465 are interchangeable in that both are mounted on a 5-bolt pattern and would fit on 12 inch hub/drums. However, the 7K brake has a stronger magnet and upgraded brake shoes with greater stopping power than the 6K. Even though they would fit, you would not want to put the 6K Nev-R-Adjust # 23-459, # 23-458 on a trailer with a 7K pound axle. You...
view full answer... - Replacement Brake Assembly Recommendation for 2004 Fleetwood Prowler Regal 32'Best option is to match the part number you found on your trailer. Realistically the 6k and 7k brake assemblies are mostly interchangeable as they both are 12 inch diameter by 2 inch width so either would technically fit, but going with the correct rating gives you a setup that's easiest to fine tune braking power. If you go with an assembly rated too high the magnet is more sensitive and you'll find that the brakes are harder to get the exact amount of braking power. It'll either feel...
view full answer... - How to Convert 7k Surge Brake Axles to Electric BrakesYou can pretty easily convert a trailer from surge brakes to electric brakes. It basically will require you to remove all of the hydraulic lines, lock out the actuator (or replace it), remove the hubs to replace the assemblies with electric units, and then wire up the assemblies. I attached a help article that will walk you through this entire process. For 7k rated Dexter brake assemblies you would want the part # 23-465 for the right hand side and part # 23-464 for the left hand side. For...
view full answer... - Weak Brake Troubleshooting and Replacement Brake Assemblies for 7k Trailer AxleThere are a couple things you should check before you would want to replace your brake assemblies. I would check the main ground for the trailer. This is the wire that runs from the trailer connector to the trailer frame and provides the ground for the entire trailer. The ground strap may have come loose and now may not be strong enough to fully apply the trailer brakes. Some brake assemblies are manually adjusted. They could very easily be in need of adjustment. You will want to have...
view full answer...
- Brand New 7k Dexter Brake Assemblies on Trailer are Not Strong EnoughWhether you have the 7K Dexter brake assemblies like part # 23-181 or like the Nev-R-Adjust # 23-465, you may simply need to adjust the brakes. Even if your brake controller is set to the highest setting, if your brakes are not adjusted properly then they will not perform correctly. You can adjust your brakes using the Brake Adjustment Spoon for Drum Brakes # W80630 until they are set at the desired braking strength. If you check out the attached review video you can see the access holes...
view full answer... - Dexter 7,000 lb Rated Brake Assembly Recommendation for TrailerDexter would be the final authority on the capacities of their axles. For 7k rated Dexter brake assemblies you would want the part # 23-465 for the right hand side and part # 23-464 for the left hand side. What you described is not uncommon for Dexter axles. There are other instances where the difference between the capacities of two axle setups is either the assemblies or the hubs they put on them.
view full answer... - What Hub/Drums Are Recommended for Timbren 3,500 lb Axle Less SystemThe Timbren 3.5k Axle Less System part # ASR35HDS02 that you referenced does require higher capacity hubs than what you currently have. For a hub/drum that is the same as your current hubs you would want the part # 8-201-9UC3-EZ. This hub comes with the correct fitting bearings for the Timbren axle spindle. For brake assemblies you would then want the part # 23-465 for the right hand side and part # 23-464 for the left hand side.
view full answer...
- Replacement Bearing Kit for Dexter 6K Axle With 031-017-02 and 031-030-02 Wheel BearingsI was able to cross reference the 031-17-02 bearing to a 14125A and the 031-030-02 to a 25580. For a replacement bearing/race/seal kit, you'd use part # BK3-200, which includes the 14125A outer bearing, the 25580 inner bearing, the 10-36 grease seal and a replacement cotter pin. Should you need them, we offer replacement hubs as part # 8-219-13UC3 and replacement self adjusting brake assemblies are # 23-465 for the right side and # 23-464 for the left side.
view full answer... - Replacement Brake Assemblies for Replacing Dexter 023-357The Dexter part number 023-357-00 is a 12x2 electric brake assembly. The correct RH assembly to use to replace what you have would be the part # 23-459 and for the LH assembly you would want the part # 23-458 if you have 6K axles. If you have 7k axles you would want part # 23-458 for the LH side and part # 23-465 for the RH side.
view full answer... - Recommended Brake Assemblies for 7,000 Pound Trailer Axle, 2009 Heartland Bighorn 3370RLIt is best to confirm the axle capacity before purchasing brake assemblies. There should be a sticker or label on the axles with information such as their capacity. If you do find that your axles are 7,000 pound axles, I recommend using the Dexter 12 Inch Nev-R-Adjust Electric Brake Assembly, left hand side # 23-464 and right hand side # 23-465. These brake assemblies automatically adjust to provide optimum performance and braking power. In addition to eliminating the need for brake adjustments,...
view full answer... - Nev-R-Adjust Electric Drum Trailer Brakes for a Trailer with 7K Dexter AxlesMost 7K axles are going to use 12 inch by 2 inch brakes. To determine if these are the right size you can measure the internal diameter of the drum and the width where the pads would make contact with the drum. I am confident that it will turn out to be 12 x 2 inches. For Dexter Nev-R-Adjust electric trailer brakes for 7K axles use # 23-465 for the right hand side and # 23-464 for the left hand side. These brake assemblies mount on a 5-bolt mounting flange. Even though these are Nev-R-Adjust...
view full answer... - Replacement Trailer Brake Assembly and Hub/Drum for 2019 Forest River Cedar Creek 37TRH 5TH WheelThe Dexter Nev-R-Adjust Electric Trailer Brake Assembly # 23-465 is the replacement for your passenger side brake assembly. This matches what was put on by Dexter. The Dexter Trailer Hub and Drum Assembly # 8-219-13UC3 matches what was originally put on your 2019 Forest River Cedar Creek 37TRH, with one exception. You axle has the E-Z cap that you can either transfer to the new hub assembly.
view full answer... - Will Dexter Brake Assemblies Fit on a Lippert AxleYou will have no problem using a Dexter brake assembly on a Lippert 7K axle. We have installed several Dexter brake assemblies on Lippert axles at our shop. Lippert and Dexter use the same standard mounting pattern and brake sizes. If you want standard brake assemblies, you could go with the Right Hand brake # 23-181 and the Left Hand brake # 23-180. I recommend stepping up to the Dexter Nev-R-Adjust brakes, # 23-465 and # 23-464. The cost difference is very minimal compared to the standard...
view full answer... - Replacement Hub/Drums and Self Adjusting Brake Assemblies 2008 Forest River XLR Toy HaulerWe definitely can help you pick out all new hub/drums and self adjusting brake assemblies for your 2008 Forest River fifth wheel XLR 39X12 toy hauler. Based on the dimensions you listed you have a number 42 spindle so for a hub/drum to fit that you'd want the part # 8-201-9UC3-EZ and then for self adjusting brake assemblies you'd want the part # 23-465 for the right hand side or part # 23-464 for the left hand side.
view full answer...
- Comparing Dexter Electric Trailer Brake Assemblies 23-181/23-180 and 23-465/23-464The only difference between the Dexter Electric Trailer Brake Assembly part # 23-181 for right hand or part # 23-180 for left hand and the Dexter Nev-R-Adjust Electric Trailer Brake Assembly part # 23-465 for right hand or part # 23-464 for left hand is the adjustment. The former are manual adjust brakes and the latter are self-adjust brakes. The manual adjust brakes require you to adjust them for even pad wear every so often whereas the self-adjust do this automatically. The adjustment...
view full answer... - Is there a Difference Between Dexter 6k and 7k Rated 12x2 Electric Brake AssembliesActually for a 6k rated Dexter 12x2 brake assembly you would want the part # 23-459 for the right hand side and part # 23-458 for the left hand side. Then for a 7k rated assembly you would want part # 23-465 for the right hand side and part # 23-464 for the left hand side. The magnets are rated differently. That is the biggest difference.
view full answer... - Correct Replacement Left and Right Hand Braking Assemblies for a 12x2 Brake AssemblyFor you, you'll just need to order two of the Dexter Nev-R-Adjust Electric Trailer Brake Assembly # 23-464 for the left hand, and # 23-465 for the right hand side.
view full answer... - Replacement Brake Assembly for 2007 Newman with 7k AxlesThe simplest replacement brake assembly solution we have for your 2007 Newman with 7,000 lb axles is the part # 23-465 for the right hand side and part # 23-464 for the left hand side. These are self adjusting too which means you won't have to worry about ever needing to tighten them up.
view full answer... - Replacing Electric Drum Brakes With Electric Over Hydraulic Disc Brakes On A 2017 Keystone AvalancheThe information I could find about your 2017 Keystone Avalanche was fairly limited, it does look like 7,000 pound axles were used. Using that information, I do have a full parts list with quantities listed below and this is a pretty common upgrade, so it is definitely possible. However, I definitely recommend contacting Keystone with the trailer's VIN to double check that I am correct about said capacity. Though not necessarily a plug and play system, as there will not be, this is pretty...
view full answer... - Can 7,000 lb Dexter Nev-R-Adjust Trailer Brakes be Used on 6,000 lb AxleYes, so long as your 6,000 lb Dexter axle has a 5-bolt brake mounting flange (which it should), then you can use the Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs # 23-465. If you also need the left hand side the correct part number is the Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Left Hand - 7,000 lbs # 23-464.
view full answer... - Determining the Right Brake Assembly and Hub Drum H and H Cargo TrailerTo get the correct brake assembly, you need to know the axle weight capacity, the backing plate bolt pattern, and the dimension of the drum. A 7000 lb axle would typically use a 12 x 2 assembly with a 5 bolt backing plate. Parts # 23-464 and # 23-465 are a good example. For replacement drums, we would need to know the wheel bolt pattern (which is typically 8 on 6-1/2) and the reference numbers off of the existing wheel bearings. Part # 8-219-4UC3 would be a typical hub and drum for a 7000...
view full answer... - Which is Best: Dexter, Tekonsha, or etrailer.com Brake AssembliesThe three brands of brake assemblies are made by different companies. None of them are made by each other. It might seem strange but if it were my trailer I would install Dexter assemblies. They have the best reputation because they are designed well and use high quality components. You really can't beat Dexter's axle components. For a 7k rated axle the best setup around is going to be the Dexter self adjusting assemblies part # 23-465 for the right hand side and part # 23-464 for the...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Lindsey S
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Hannah L
Installed by:
Jeff D
Video Edited:
Joshua S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Sid
11/28/2023
Its been another year and the parts are still functioning flawlessly.