Do the Dutton-Lainson Boat Trailer Deluxe Roller Bunks Have to be Installed on Bunk Boards
Question:
I have a 2007 Tracker Targa 165 SC boat and trailer setup. The lags on the bunk boards fell out and its time to replace. Im intrigued with going to a roller setup, however I do not want to raise the boat up. For me, it makes no sense logically to attach this product to a set of wooden bunk boards. It seems redundant and unnecessary. Can I just attach these to the factory mounting brackets. The existing mounts are 1/4 welded directly to the frame. I would be raising the boat up slightly more than stock but not nearly as much as putting this product on new bunk boards. see photos Im not 100 sure of the boat, motor fuel weight. I believe these rollers will work and might be overkill. But other models on eTrailer seem too light. The duct tape and zip ties were an emergency repair. As I backed down the ramp I noticed the one bunk board was floating funny and only attached by the last lag bolt.
asked by: Ray C
Expert Reply:
If you do not want to mount the Dutton-Lainson Boat Trailer Deluxe Roller Bunk # DL21741 to the bunk boards, there are brackets that can be used.
- Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks # DL21742 (4 needed to mount a pair of boards)
Looking at your pictures, your current brackets appear to have a similar bracket/hole placement as the # DL21742 brackets. So there is a decent chance that you can reuse those brackets.
Knowing that you can always fall back to using the # DL21742 brackets, I would just try fitting the Dutton-Lainson Boat Trailer Deluxe Roller Bunk # DL21741 to your current brackets and if they don't work, pick up the # DL21742 brackets.
Products Referenced in This Question
Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks Parts DL21740 & DL21741
- Boat Trailer Parts
- Bunks
- Rollers
- Roller Bunk Bracket
- Zinc-Plated Steel
- Dutton-Lainson
more information >
Product Page this Question was Asked From
Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers
- Boat Trailer Parts
- Bunks
- Rollers
- Roller Bunk
- Black Rubber
- Dutton-Lainson
more information >
Continue Researching
- Shop: Boat Trailer Deluxe Roller Bunk - 4' Long - 10 Sets of 3 Rollers - by Dutton-Lainson
- Video: Dutton-Lainson Roller Bunks for Boat Trailers Review
- Shop: CE Smith U-Bolts - Galvanized - 3-13/16" Long x 3-1/16" Wide x 1/2" Diameter - Qty 8
- Shop: Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks Parts DL21740 & DL21741
- Shop: Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks Parts DL21754 & DL21755
- Shop: CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" - Qty 4
- Shop: Shackle Strap - 3-1/2" Long
- Q&A: Is Installation Hardware Included with Dutton-Lainson Roller Bunks
- Q&A: How Many Bolts are Required to Install the Dutton-Lainson Roller Bunks # DL21741
- Q&A: What are the Dimensions for the Boat Trailer Roller Bunk Bracket # DL21742
- Q&A: Size of U-Bolt Slots in Dutton-Lainson # DL21742 Roller Bunk Bracket for Roller Bunks DL21740/41
- Search Results: winch strap
- Search Results: dutton~lainson
- Search Results: dl21755
- Q&A: Where Do Roller Bunks Typically Locate on a Boat Trailer
- Q&A: Can Dutton-Lainson Roller Bunk be Attached Directly to Carpeted Bunks on a Boat Trailer
- Shop: Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers
- Video: CE Smith Boat Trailer Carpeted Bunk Boards Review and Installation
- Video: Review of CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE27845
- Q&A: How to Determine U-Bolts and Fasteners Needed to Install SE Smith Bunk Boards and Brackets
- Video: Dutton-Lainson Boat Trailer Parts - Roller and Bunk Parts - DL21754 Review
- Search Results: 25580
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: leaf spring
- Shop: Trailer Wiring
- Article: Trailer Tire Sizing
- Shop: Brake Controller
- Search Results: fender
- Article: Most Popular Wheel Bearings