Is Installation Hardware Included with Dutton-Lainson Roller Bunks

Question

Question:

Does the hardware nuts bolts etc come with thedl21742 and thedl21740? If not what does it take to install brackets and rollers to frame

asked by: Kim

0

Expert Reply:

The roller bunks # DL21740 and # DL21742 do not include the mounting hardware. You will want to use corrosion resistant hardware such as galvanized or stainless steel fasteners, since it is for a marine application. The hardware is not included because there are different ways to mount the bunks, direct or using brackets, so they did not include hardware. You will need to decide what works best for you and your trailer.

expert reply by: Michael H

0

Answer 1

I pulled a Boat Trailer Roller Bunk Bracket #DL21742 from our warehouse to get the dimensions for you. The overall length is 10-3/8 inches, the length minus the top bracket would be 10-1/16 inches. The height of the main bracket is 7/8 of an inch and…

view full answer...

Answer 2

If you do not want to mount the Dutton-Lainson Boat Trailer Deluxe Roller Bunk #DL21741 to the bunk boards, there are brackets that can be used. - Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks #DL21742 (4 needed to mount a pair of…

view full answer...

Answer 3

A minimum of two bolts will need to be used to install each Dutton-Lainson Roller bunk part #DL21741. You can also use the Roller Bunk Brackets #DL21742 to install the bunks. A pair of these are required to install each bunk.

view full answer...

Answer 4

The Dutton-Lainson Roller Bunk Bracket, part #DL21742, fits Dutton-Lainson Roller Bunks #DL21740 and DL21741. Four are needed to mount a pair of roller bunks. My contact at Dutton-Lainson advises that u-bolts are not specifically required to install…

view full answer...

Answer 5

For an 11 foot long bunks, using 2 sets of the Dutton-Lainson roller bunks, #DL21741, would work well. The capacity for a set is 3,000 pounds so a 2,000 pound boat should not be an issue. You can use your own hardware to secure the rollers to your…

view full answer...

Answer 6

You want to locate the rollers on the frame of your trailer so that they overhang slightly off the back of the trailer so that the boat will contact them before any other portion of the trailer as you load it onto the trailer. I attached a picture…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Is Installation Hardware Included with Dutton-Lainson Roller Bunks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching