Can Roller Bunks be Used on Boat Trailer of 16 ft Sea Nyph Fishing Machine

Question

Question:

will these work with a 16ft seanyph fishing machine

asked by: Warren H

1

Helpful Expert Reply:

I looked up pictures of trailer that typically carry the 16 ft sea nyph fishing machine and yes roller bunks like the # CE27700 can be used on it.

expert reply by: Jameson C

1

Answer 1

You have a couple of options for rollers on your Shorelander trailer. If you want to completely cover the 7 foot bunks you currently have, you can attach a 4 ft roller like part #CE27700, and cut another to cover the 7 ft board. If you do mount the…

view full answer...

Answer 2

Yes, if you have 8 foot long bunks currently then you'd want to install a total of two 4 foot rollers on each bunk like what comes with the #CE27700. So you'd need a quantity of two of this part number and you'd be set.

view full answer...

Answer 3

Although you may be able to get by with just using one set of 5 foot roller bunks, I am a firm believer that in this case more is better. Having rollers the entire length of your wood bunks will not only make the loading and unloading process easier…

view full answer...

Answer 4

For your Commercial Crab Boat, I recommend the CE Smith Roller Bunks for Boat Trailers - 5 Rollers Each - 4' Long - 1,500 lbs - 1 Pair #CE27700. These 4 foot long rollers are 4-3/4 inches wide x 2-1/2 inches diameter. I recommend using the CE…

view full answer...

Answer 5

If the brackets don't allow enough swivel to allow the roller bunks to fit flush on the boat, I recommend replacing the brackets with bolster brackets that will allow enough swivel like the CE Smith Bolster and Swivel Bracket Assemblies -…

view full answer...

Answer 6

Bunk rollers like the #DL21754 you mentioned would be an excellent choice for PWC's that rest on the edges of the bunks, as most of them do. At 4 foot long, they'd probably offer plenty of support, but I'd recommend getting a set…

view full answer...

Answer 7

Normally at the front of the trailer where the jack is there's a keel roller like the part #CE32005G for a 2 inch wide trailer tongue or part #CE32003G for a 3 inch wide tongue that the jack pulls the jet ski up to and is held in place.

view full answer...

Answer 8

We have roller bunk brackets like the part #DL21742 which have a swivel on the top of them which can angle of the hull with bunks like the part #DL21740. I attached a picture that shows the rollers being used on a boat with an angled hull.

view full answer...

Answer 9

For the 10 foot long bunks you have two sets of the CE Smith roller bunks part #CE27700 would work well for you. These can be mounted directly to the wooden bunks you have already or you can remove them and install them with the brackets part…

view full answer...

Answer 10

It is best to have the Dutton-Lainson Boat Trailer Deluxe Roller Bunk #DL21740 swivel. This will allow the #DL21740 to move with the boat when loading it on the trailer.

view full answer...

Answer 11

The CE Smith Roller Bunks, #CE27700, that you referenced would be a great option for your boat trailer. These roller bunks are 4 ft long and they can be mounted directly on top of your current wood bunks. You can also use the CE Smith Mounting…

view full answer...

Answer 12

What I recommend is to use 2 sets of the roller bunks #DL21740. Two bunks can cover the length of one bunk but you will need to trim one to fit. One set would be needed per bunk and then trimmed to fit. One roller bunk alone is 4 feet long. Normally…

view full answer...

Can Roller Bunks be Used on Boat Trailer of 16 ft Sea Nyph Fishing Machine

Product Page this Question was Asked From

Continue Researching