Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
(254 reviews)
Price: $127.50
Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
Item # TJDP-7000S-B
Our Price: $127.50
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
- All Info
- Reviews (254)
- Q & A (0)
- Photos
etrailer Trailer Jack - TJDP-7000S-B
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- 6001 - 7000 lbs
- Sidewind Jack
- Swivel Jack
- Pipe Mount
- Weld-On
- Leveling Jacks
- Tongue Jacks
- 28 Inch Lift
- With Rectangle Foot
- Steel
- etrailer
Weld-on, pipe-mount swivel jack pivots up for travel, down for use. Square design provides side-load support. Retracted height is 14-1/2". Extended height is 29-1/2". Drop leg offers 13-1/2" of lift on top of 15" of screw travel.
Features:
- Utility jack lets you raise and lower your trailer
- Ideal for agricultural and commercial applications
- Tubular swivel design lets you twist jack up for storage, down for use
- Pull pin with clip holds jack in place
- Lanyard connects pin to jack so it won't get lost
- Square jack provides more side-load capacity than round-tube jacks
- Belly band welded to the outer tube provides extra strength
- Sidewind handle has zinc finish for attractive look and rust resistance
- Drop leg allows for increased lift and saves time when raising or lowering
- Black painted outer tube
- Zinc finished inner tube and footplate for corrosion resistance
- Welded-on footplate minimizes sinking in soft ground
- Effortless greasing with built-in grease zerk
- Weld-on installation with included female pipe mount
Specs:
- Jack height (from bottom of foot to center of pipe mount):
- 14-1/2" Retracted
- 29-1/2" Extended
- Total lift: 28-1/2"
- Screw travel: 15"
- Drop leg travel: 13-1/2"
- Lift capacity: 7,000 lbs
- Support capacity: 8,000 lbs
- Outer tube width: 2-1/2"
- Inner tube width: 2-1/4"
- Footplate dimensions: 8" long x 6" wide
- Pipe mount diameter:
- Inner: 2"
- Outer: 2-1/2"
- Handle radius: 8-1/8"
- Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole
- 1-Year warranty
TJDP-7000S-B Ram Square Pipe Mount Swivel Jack w/ Footplate - Weld On - Side Wind - 15" Screw Travel - 7,000 lbs
Compare to Bulldog BD190758
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Arrived Damaged
- Product did not meet expectations
- Wrong item was ordered
Customer Reviews
Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K - TJDP-7000S-B
Average Customer Rating: 4.8 out of 5 stars (254 Customer Reviews)
Weld-on, pipe-mount swivel jack pivots up for travel, down for use. Square design provides side-load support. Retracted height is 14-1/2". Extended height is 29-1/2". Drop leg offers 13-1/2" of lift on top of 15" of screw travel.by: Gary12/20/2018
These are sweet jacks. I installed a pair on the rear of my 20ft bumper pull equipment trailer. These things will lift the entire trailer off the ground. Comes in handy changing flats. The reason I installed them was to stop the bobcat from lifting my truck off the ground when loading. Got tired of carrying 6x6 blocks to put under the rear of the trailer. I really like the swing feature. When stowed I crank them against the tail light bracket to keep them quiet.
by: Richard 01/23/2023
Exactly what I needed to be a drop leg for loading my Kubota on my trailer without lifting the truck off the ground.
Richard
1/24/2024
Still working great of not better than when new. Definitely keeps from bad things happening loading my trailer.
by: Brian 02/03/2024
It is a good jack. I had to cut mounting bracket off and weld in different location for my application but so far it has worked out well.
by: Tracy 02/20/2023
Nice unit. Just what was looking for.
Tracy
2/21/2024
We liked it so much that we traded in the piece of equipment we put it on and saved it for another!
Jesse M.
2/21/2024
@Tracy Thanks for sharing! Definitely good to hear!
by: Andy K09/15/2017
Used 2 of these pipe mount swivel jacks on the back of a 16k gvw sure trac dump trailer to stabilize the rear of the trailer when loading and unloading equipment. Without these jacks the trailer rear end would go down when pulling a 10k bobcat up the equipment ramps and the truck pulling the trailer would go up dual tires and everything , not good. Excellent sizing, price, and build quality, would recommend to a friend
by: Randy 03/29/2024
Great heavy duty product... put this on my towable Geni lift... Would buy again
by: Frank 08/08/2023
The products ordered were received when expected excluding the USPS delays, and were as expected. I ordered a replacement swivel jack for my Hay Cutter and was pleasantly surprised that it did a better job then the one that came with the cutter (Part# TJDP-7000S-B). All other products received were as described and received in good condition. What more can you ask for.
by: John05/30/2018
Very good, weld on. Only complaint is the slop between the mounting male bracket and female. It causes the camper to lean typically to the drivers side. I’m going to try welding some beads around the male side and build it up to get rid of the slop.
by: Allen02/01/2018
Been usin these for a year now and love them! Never have had one issue with them. Since the mini off rd camper sits on 35" tires and a spring over the drop down extended legs are perfect. I would recommend to anyone who needs the extra length for a high riding trailer or camper.
by: Kathy 03/17/2024
Thank you for fast delivery. Friendly staff and very helpful.
I would buy this jack again. Thank you
by: B. Lincoln02/11/2024
Work good. Fit good. They do their job.
by: Jerry03/30/2022
Had this welded on to my old trailer that did not have a jack. Plenty of power to raise my flatbed trailer with a compact tractor on it. Small price to pay for making my trailer so much easier to use. It's nice that it pivots to run perpendicular to the trailer.
by: George 06/15/2023
Finally a heavy duty jack . Well worth the $
by: Luxurious Restrooms09/06/2023
The product us great. Shipping was fast.
by: Karla 05/03/2021
I bought two of these jacks. One for a bale processor and one for a 10' John Deere rotary mower. Both jacks have held up very well. The one for my bale processor has been a great help to me. In the past I had a hard time finding a jack that would work on all the uneven ground that I had to deal with. I had actually thought about buying another of these jacks for our boom sprayer.
Karla
5/3/2022
Still working great, no problems. Wish I had bought a couple more.
by: Mike 03/02/2023
Has a greater lifting capacity that the jsck that is on the trailer now.
by: Chris 07/15/2023
Product is exactly what I needed, sturdy and works great!
by: Joe12/23/2017
We have not launch yet. I am back at Wallops now here is a couple of pic's of your jacks and how we are using them at NASA
I will send more when we launch
Take care and thanks for your help
by: Jerry 04/03/2020
I think the company did a great job. Only thing i have issue with is a greater in depth drawing of the mounting bracket.
Jerry
4/4/2021
Great
by: Matt 06/13/2023
Excellent product!!
by: Douglas 09/18/2022
Very good build quality. Looks like a jack that can handle the work expected of it. Large footprint. The pins have a small chain on them so that they don't get lost. Crank handle is smooth. Looks like a jack that you could be proud of.
by: Gabriel09/28/2016
This is a good, heavy-duty jack. It lift my trailer with ease.
Gabriel R.
10/2/2017
Raises my trailer with ease. Great product.
by: Jack 01/25/2023
It was easy to order. The jack arrived on time as promised.
by: Allen05/20/2018
This is the 2nd set of these i have gotten from etrailer. As usual fast delivery and great service. These jacks are great and my other set is over a year old and never have had any problems with them at all. i would recommend these to anyone looking for a set with drop legs. The price cannot be beat for the quality.
25
254
Show More Reviews
See what our Experts say about this etrailer Trailer Jack
- Replacement Pipe Mount for Trailer Swivel JackThe degree of tightness of a mounted pipe-mount jack like # TJDP-7000S-B depends on the jack's fit on the trailer mount and on the pin. Any differences in the diameters of the holes versus the pin will allow for some small amount of movement. If for example the trailer is older and very well-used the holes in its pipe mount could be rounded out slightly; the same could happen to the mount on the jack. If the holes are enlarged from years of friction you might be able to find a slightly...
view full answer... - Can a Swivel Mount be Added to Square Direct Weld Trailer Jack # TJD-7000SSquare Direct Weld Jack # TJD-7000S will weld directly to the trailer frame. To make it a swivel jack you would have to weld on pipe mounts such as # BD015279 and # BDPG9810-00. Or you could go with jack # TJDP-7000S-B that already has the mount welded to the jack and includes the pipe that gets welded to the trailer frame. I have linked a video review of this jack for you.
view full answer... - Can the Trailer Valet XL Mount Be Used With The Trailer Valet 5X Trailer Jack? The Trailer Valet XL Mounting Bracket # TVXLMB is actually designed to work exclusively with the Trailer Valet XL Trailer Dolly with Chain Drive # TVXL25 & # TVXL2 and will not work with the Trailer Valet 5X Swivel Jack and Trailer Mover - Topwind # STC-V211, unfortunately. Instead, since your frame is taller than 6", your best bet is to use a weld-on jack like the Square Pipe Mount Swivel Jack w Footplate - Drop Leg # TJDP-7000S-B. This jack will weld directly to the side of your trailer's...
view full answer... - How Much Does The Square Pipe Mount Swivel Jack w Footplate # TJDP-7000S-B Weigh? The Square Pipe Mount Swivel Jack w Footplate # TJDP-7000S-B weighs just 28lbs.
view full answer... - What Size Pin Does the Pipe Mount Use On the Square Pipe Mount Swivel Jack TJDP-7000S-B UseIn regards to the Square Pipe Mount Swivel Jack part # TJDP-7000S-B, the pin that is used to secure the jack to the pipe mount is 5/8" diameter.
view full answer... - Recommended Weld-On Swivel Jack to Fit a 20 Ft. Triton Boat TrailerWe carry a large selection of weld-on jacks that will fit your Triton boat trailer. I have attached a link that will tack you to the product page that has all of these jacks for your to review. As for a jack that I recommend, I like the Square Pipe Mount Swivel Jack Weld On Sidewind, 7K, # TJDP-7000S-B. This jack has a 7,000 lbs lift capacity and has the 2-1/2 inch round tube swivel on the jack. Retracted the jack measures 17-1/2 inches and fully extended the jack will measure 29-1/2 inches...
view full answer... - Economically Priced Trailer Jack with Swivel Pipe Mount that Welds OnFor similar jack with the best price check out the Pro Series jack part # PS1400400303. This welds on with a pipe mount like the jack you referenced and swivels down when needed. It has a 2,000 lb capacity and a topwind.
view full answer... - Swivel Mount Trailer Jack for 6 Inch Tall Trailer FrameThe only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part # STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4" wide x 6" tall. In addition to featuring a bolt on tongue jack, the Trailer Valet as the name states doubles as a trailer dolly which will easily allow one person to move their trailer around. The dolly has integrated brakes which keep it from rolling....
view full answer... - Recommendation for Pipe-Mount Swivel Trailer Jack that has a Grease FittingRound, Pipe Mount Swivel Jack w/ Footplate - Weld On - Topwind - 15-1/4" Travel - 7K Item # TJP-7002-B does not have a grease fitting. But there is a another option that does. Take a look at Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 15" Travel - 7K Item # TJDP-7000S-B. This version does have the grease fitting and has nearly identical specs as its round-tube brother. I have included a link to a video review of this jack for you.
view full answer... - What is Total Height Range of etrailer Jack # TJDP-7000S-BSo the jack you are interested in part # TJDP-7000S-B has a drop leg that can travel up to 13-1/2 inches and has a jack that can travel 15 inches by cranking the handle for a total lift of 28-1/2 inches.
view full answer... - Replacement Mounting Brackets for Square Pipe Mount Swivel Jack w Footplate TJDP-7000S-BIn regards to the Square Pipe Mount Swivel Jack w Footplate part # TJDP-7000S-B, we offer both the Replacement Male Pipe part # TJP-OP58 and the Replacement Female Pipe part # TJP-FP58 but the chain and pin is not available separately. It just takes a standard 5/8" diameter pin like part # 325-GH-099.
view full answer... - 7k Trailer Jack Recommendation for Enclosed TrailerThe Square Pipe Mount Swivel Jack # TJDP-7000S-B is a weld-on 7k trailer jack that would work well for you. The pipe mount would weld to the frame of the trailer and allow you to swivel up and down when needed. You should also note that our jacks are rated for lifting strength (tongue weight) and not for the total trailer weight. For the size of your cargo trailer you most likely would have a 700 lb tongue weight which this jack would make easy work of.
view full answer... - Total Height of Swivel Trailer Jack While RetractedTo total retracted height of the swivel jack # TJDP-7000S-B is 24-1/2 inches.
view full answer... - Does the Pipe Mount BDPG9810-00 and Trailer Jack TJDP-7000S-B Have Same Pipe DimensionsYes the pipe diameters of the # BDPG9810-00 and the # TJDP-7000S-B are the same. Both of them have a 2 inch inner diameter and a 2-1/2 inch outer diameter.
view full answer... - Parts Used To Create The Square Pipe Mount Swivel Jack With Footplate If you are looking for the parts needed to mount the jack # TJDP-7000S-B, the parts are already included in the packaging. To mount, place female pipe # TJP-FP58 in the proper location for trailer application. Weld on all the way around the female pivot pipe with 3/16" filet weld. Just in case you need it, I have the breakdown of the parts used to create the Square Pipe Mount Swivel Jack w Footplate # TJDP-7000S-B. You will need Replacement Drop Leg with Foot for etrailer and Ram Square,...
view full answer... - What Material is The Drop Leg On The Square Pipe Mount Swivel Jack # TJDP-7000S-B? Yes, the drop leg on the Square Pipe Mount Swivel Jack # TJDP-7000S-B is steel. The parts have a zinc finish so you will need to clean off the finish where you intend to weld so the weld does not get contaminated with the coating and be sure the area is well ventilated since the coating can be hazardous. We do have the Weld-On Pipe # TJP-FP58 which fits this jack for additional mounts.
view full answer... - Will Swivel Jack Handle Move When in Stowed Position?The handle for the Square Pipe Mount Swivel Jack, # TJDP-7000S-B, is going to be stiff enough that it will not free float. For example, if you refer to the picture I've attached, you can see the handle sitting in an upright position. You can also take a look at the video I've linked, and at about the 1:30 mark, you will be able to see the handle being used and then come to a stop without falling back down
view full answer...
- Shelby Side Wind Trailer Jack, Part # 6108SW for Triton TrailerI think the Square Pipe Mount Swivel, part # TJDP-7000S-B would be a good choice for you. It has the 8,000lb support capacity which is one of the highest we offer, and is welded to the trailer frame.
view full answer... - Trailer Jack To Support 6X12 Trailer Weighing 2,500 Plus PoundsYes, The Square Pipe Mount Swivel Jack w Footplate # TJDP-7000S-B would be able to lift your trailer from the side to change a flat tire. The jack has a 7,000 pound lift capacity and has a 8,000 pound support capacity. The jack has a weld-on installation. I attached a review video link below.
view full answer... - Bolt-On Swivel Jack For Leveling Tear TrailerFor a jack that is similar and has a bolt-on installation I recommend the Trailer Valet JXS Trailer Jack w/ Footplate # TV64FR. This is a sidewind swivel jack with a 5,000 lb support capacity that fits a frame up to 4-3/4" tall x 3-3/4" deep. However, something like the Ark XO Drop Down Corner RV Stabilizer Jacks # ARK87FR would probably be a better choice. Since these install on the corners it won't be so unstable. These have a retracted height of 19" and extended height of 25" for...
view full answer... - Does the Square Pipe Mount Swivel Jack TJDP-7000S-B Come with the Weld On MountThe Square Pipe Mount Swivel Jack w Footplate part # TJDP-7000S-B does indeed come with the pipe mount that gets welded to the trailer frame that the jack gets attached to and swivels on.
view full answer... - Dimension of Square Pipe Mount Swivel Jack w Footplate # TJDP-7000S-B The Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K # TJDP-7000S-B has a measurement of 10 inches from the top of the jack to the center of the swivel mount. The total retracted jack height from top to bottom is 24-1/2 inches.
view full answer... - Is 28-1/2 Inch of Lift of TJDP-7000S-B With Leg Fully ExtendedYes, the 28-1/2 inches of extension for the Square Pipe Mount Swivel Jack # TJDP-7000S-B is with the leg fully extended.
view full answer... - Bolt-On Swivel Jack Options for 6" Tall Trailer FramesThe only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part # STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4" wide x 6" tall. In addition to featuring a bolt on tongue jack, the Trailer Valet as the name states doubles as a trailer dolly which will easily allow one person to move their trailer around. The dolly has integrated brakes which keep it from rolling....
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Updated by:
Lindsey S
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Mike S
Updated by:
Manda E
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Video Edited:
Jacob T
Video Edited:
Chris R
Installed by:
Cole B
Installed by:
Adam E
Installed by:
Aidan B
Written by:
Amanda M
Video by:
Jonathan Y
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Gary
12/22/2019
Holding up perfect. Just like the day I installed them. Super strong.