Parts Used To Create The Square Pipe Mount Swivel Jack With Footplate

Question

Question:

Hi Etrailer, I need help determining what parts are used to create the swivel jack mount for product number TJDP-7000S-B

asked by: Bryan M

0

Expert Reply:

If you are looking for the parts needed to mount the jack # TJDP-7000S-B, the parts are already included in the packaging. To mount, place female pipe # TJP-FP58 in the proper location for trailer application. Weld on all the way around the female pivot pipe with 3/16" filet weld.

Just in case you need it, I have the breakdown of the parts used to create the Square Pipe Mount Swivel Jack w Footplate # TJDP-7000S-B.

You will need Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-FT.

For the pipe mount you need the Replacement Male Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 2" - 5/8" Pin Hole # TJP-IP58-CTN, Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks - 5/8" Diameter # TJP-PN58 and Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 5/8" Pin Hole # TJP-FP58.

Also needed is the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K # TJD-7000S-HD and the Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 7,000 lbs # TJD-7000S-GR.

The manufacturer advised there is no replacement for the inner tube and outer tube.

expert reply by: Timothy G

0

Answer 1

The Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs Item #TJD-7000S-GR has the replacement pins in the kit. The washer can just be replaced with any washer that will fit over the shaft. You just want…

view full answer...

Answer 2

I went out into our warehouse to grab the gear set part #TJD-7000S-GR that you mentioned and the outer diameter of the larger gear is 1.7 inches with an inner diameter of .53 of an inch. The smaller gear has an outer diameter of 1.39 inches with the…

view full answer...

Answer 3

I have a solution for you, but we do not have any replacement lights that will fit in those grommets. Instead, you can use the LED Clearance or Side Marker Light #MCL002AXB (amber) and #MCL002RXB, which require a rough cutout dimension of…

view full answer...

Answer 4

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each end…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Parts Used To Create The Square Pipe Mount Swivel Jack With Footplate

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching