Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
(774 reviews)
Price: $77.76
In Stock
Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
Item # TJD-5000S
Our Price: $77.76
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (774)
- Q & A (0)
- Photos
etrailer Trailer Jack - TJD-5000S
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- 2001 - 3000 lbs
- Sidewind Jack
- Weld-On
- Leveling Jacks
- Tongue Jacks
- 29 Inch Lift
- With Rectangle Foot
- Steel
- etrailer
Weld-on jack has a retracted height of 24-5/8" and an extended height of 39-7/8". The square design provides superior side-load support. Drop leg offers 13-1/2" of lift on top of 15-1/4" of screw travel. Includes sidewind handle.
Features:
- Utility jack lets you raise and lower your trailer
- Ideal for agricultural and commercial applications
- Square jack provides more side-load capacity than round-tube jacks
- Sidewind handle has zinc finish for attractive look and rust resistance
- Drop leg allows for increased lift and saves time when raising or lowering
- Pin and clip holds leg at desired location
- Effortless greasing with built-in grease zerk
- Black powder coated outer tube and zinc finished inner tube and footplate for corrosion resistance
- Welded-on footplate minimizes sinking in soft ground
- Weld-on installation
Specs:
- Height (from bottom of foot to top of jack):
- 24-5/8" Retracted
- 39-7/8" Extended
- Total lift: 28-3/4"
- Screw travel: 15-1/4"
- Drop leg travel: 13-1/2"
- Lift capacity: 3,000 lbs
- Support capacity: 5,000 lbs
- Outer tube width: 2-1/4"
- Inner tube width: 2"
- Footplate dimensions: 7-1/2" long x 3-3/4" wide
- Handle radius: 7-3/4"
- Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole
- 3-1/2" Between center of hole on bottom and center of nearest hole
- 1-Year warranty
TJD-5100S Ram Square Direct Weld Jack w/ Footplate - Drop Leg - Side Wind - 15-1/4" Screw Travel - 3,000 lbs
Replaces TJD-5000S
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Product did not meet expectations
- Wrong item was ordered
Customer Reviews
Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs - TJD-5000S
Average Customer Rating: 4.8 out of 5 stars (774 Customer Reviews)
Weld-on jack has a retracted height of 24-5/8" and an extended height of 39-7/8". The square design provides superior side-load support. Drop leg offers 13-1/2" of lift on top of 15-1/4" of screw travel. Includes sidewind handle.by: Att:10/12/2023
WE HAVE BEEN USING THIS PRETTY MUCH SINCE WE RECEIVED IT WITH OUT ANY ISSUES. WE USE IT TO STABILIZE A FOLD DOWN SIDE TABLE ON THE SIDE OF A MOBILE WORK STATION THAT MOVES ALMOST WEEKLT FROM WELL TO WELL ITS GETS A LOT OF SWING IN AND OUT OF POSTION THE UP AND DOWN MOVEMENT DOESNT TRAVEL MUCH BUT IS FUNCTION FLAWLESS EVEY TIME
by: Tim 10/02/2022
Great quality jack. Only gripe, minor, is the boxing/packaging was a little deficient and they we a little beat up when I received them. Otherwise first rate.
by: James R.01/05/2018
A great product at a very good price. We replaced an old fold up jack on a 16' utility
trailer with this unit and raising the front of the trailer to hook up / unhook has become a very easy task. This jack is very well made and I would highly recommend.
by: Josh 05/15/2020
I put a couple of these on a chicken tractor and they're doing great. We use them every other day and they are outdoors 100% of the time. I've had to grease them a couple of times and I wasn't sure I was getting enough grease through the zerks so I just took the cap off which was easy enough.
by: Irma09/14/2018
This product is very resistant and of good quality and excellent price. The material and parts are all well assembled, we are using them for trailer stabilization and even though we havent mounted these, we have been using the brand and they are perfect.
by: Hannah06/25/2018
awesome customer service. I had to contact due to backordering of the product and the rep, George, was extrememly knowledgeable and helpful. He got my product switched and shipped quickly!
by: Hewy106/11/2017
These trailer jacks did exactly what I needed them for. Quality appears great, but we shall see in longevity.
by: Kevin 07/25/2022
Works well and at a great price, will probably purchase these often to replace the cheap too wind jacks that's come on new trailers
by: Paul C.06/05/2017
Product was delivered exactly as expected. It was well packaged and delivered very quickly. Condition was perfect and I'm very pleased in all concerns. I would not hesitate to order more products from them in the future. I plan on using this product for additional stabilization of my rv trailer, im sure it will provide cost effiecency, ease of use and stability.
by: Bruce12/04/2017
Everything went just fine. Awesome jacks, can't wait to work with them. I'm building an adjustable loading ramp. I saw one in St Louis and wanted to make one. Your company has a lot to choose from. I will definitely keep you folks in mind for future purchases.
by: Mje03/05/2020
Great product! Great price. Quick delivery. Would highly recommend purchasing from etrailer.
by: Kevin S07/21/2016
Haven't installed the products yet but the delivery and customer service is top notch. I would argue that the delivery is better / faster than [...] 2day shipping. I had a question and called to ask if the spindles I wanted would fit the hubs and after confirmation, placed my order on the phone.
by: Bradley03/11/2023
packaging very poor
by: P.Steve11/04/2021
great product. welded in easily, easy to operate. could not be happier. i'll shop with you again.
by: Brenton10/14/2019
Love it. After a year it looks good, doesn't rattle, and does its job.
by: Mike 11/08/2021
Bought 2 to make gate jacks for hanging gates .
Works perfect !!!
by: N. N. Walker06/12/2017
Exactly what I needed, I ordered 6 of these for a special project for my company. Delivered sooner than I expected, very satisfied with this company's service! Thank you!
by: Mike S.06/14/2016
I received the parts quicker than I expected and the were all correct and in good shape. Easy to order and quick delivery what else can you ask for!
by: GH07/18/2022
Great service, received ahead of schedu le
by: Taylor 07/12/2022
Great jack for the money!
by: Mike06/12/2019
Quick delivery at a great price.
by: Frank Yanish01/05/2017
excellent pricing/product, fastest shipping ever
by: Bruce 02/04/2024
by: Rachel 06/19/2023
by: Vrushab04/10/2023
25
769
Show More Reviews
See what our Experts say about this etrailer Trailer Jack
- Brainstorming Sidewind Trailer Jack for 2 Inch Receivers On Cargo Trailer Corners For StabilizationInteresting. We don't have that specifically, but there are a couple of routes you could go. Most trailers will use the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 # TJSC-24 for stability in the corners so you could mount a receiver shank to that and use # TJSC-24-HD as a sidewind crank. It sounds like you were picturing more of a trailer tongue style option, so you could use a jack like the etrailer Square Jack w/ Footplate - Drop Leg - Bolt On - Zinc - Sidewind - 29-1/8"...
view full answer... - Can the Side Wind Handle on a Side Mount Tongue Jack Be Switched to Mount Inside FrameI do have an option for you but you can't just switch the side of the handle on a trailer tongue jack, that's not something they allow for no matter which you go with. If you want to mount the jack inside the frame and crank from the outside you'll have to use a weld-on option like the Square Direct Weld Jack part # TJD-5000S. Please note, you'd have to weld the jack up high enough for the handle to clear the frame while in use.
view full answer... - How Much Clearance Is Needed to Use the Square Direct Weld Jack w/ FootplateThe clearance measurement you are referring to is largely going to depend on where you weld the outer tube of the Square Direct Weld Jack w/ Footplate part # TJD-5000 to your bumper. However, I can confirm that while the jack is completely retracted, the distance from the bottom of the outer tube to the bottom of the foot plate will be 2-1/2". Therefore, if you were to align the bottom of the outer tube on the jack with the bottom of your bumper you would only need 2-1/2" of clearance....
view full answer... - Recommended Keeper Pins for RAM 7000 and 5000 Series JacksHey Kelly, I went ahead and checked out all of those jacks and I believe I was able to find what you're looking for. So, for # TJDP-7000-B, # TJD-7000, # TJD-7000S, and # TJDP-7000S-B, you can use the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-PN; and for # TJD-5000 and # TJD-5000S you can use the Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks # TJP-PN58.
view full answer... - Leg Tube Dimensions and Pin Hole Diameter of etrailer Jack # TJD-5000SThe tube width of the drop leg that comes with the etrailer jack # TJD-5000S that you referenced is 1-3/4 inch square and the diameter of the pin holes is 5/8 inch.
view full answer... - Is There a Replacement Drop Leg for the Bulldog Square Jack - 3,000 Lbs 195354I do have a part number for you, "DF35000324" but the replacement drop leg for the Bulldog Square Jack with Footplate part # BD195354 is no longer available. Therefore, we could only offer you is a new jack, the Bulldog Square Jack with Footplate part # BD195354. The other option you have is to try and find some old stock of the replacement drop leg or possibly find one second hand. I will say, we do offer a very similar type of jack in the Square Direct Weld Jack with Footplate part #...
view full answer... - How Much Does 3K Square Direct Weld Jack TJD-5000S WeighSquare Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 3,000 lbs Item # TJD-5000S weighs approximately 20 pounds.
view full answer... - Can Handle on 3K Square Direct Weld Jack with Footplate TJD-5000S be Easily RemovedThe handle for Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 3,000 lbs Item # TJD-5000S can be removed but it isn't easy. You would have to take the top cap off and then drive out a roll pin and/or clips holding the handle in one of the gears. If it isn't something that you have to do you will probably want to avoid removing the handle. The same goes for any trailer jack.
view full answer... - Does etrailer Direct Weld Square Sidewind Jack TJD-5000S Use a Drop LegThe etrailer brand Sidewind Drop Leg Jack you looked at, part # TJD-5000S is actually made up of an outer tube, an inner tube that extends and retracts by actuating the crank and a drop leg that fits inside the inner tube. The drop leg can indeed be removed if necessary by removing the included snapper pin. The inner-most tube/drop leg has a series of 5 holes that further allow you to adjust the height of the jack. The jack provides a total lift of 28-3/4 inches, with 15-1/4 inches of...
view full answer...
- Can The Handle Be Replaced On The Square Direct Weld Jack # TJD-5000S For a Nut To Use a Drill? The Handle # TJD-7000S-HD is the only lift option available for the Square Direct Weld Jack # TJD-5000S. You can choose to cut the handle where it inserts into the jack and weld on a 3/4" hex nut which will allow you to use the Adapter # UF48-979005. This will allow you to use a cordless drill to operate the jack.
view full answer... - Recommendation for Square Weld-On Jack Without Drop LegI do have a solution for you, however the Square Direct Weld Jack w/ Footplate # TJD-5000S is not currently available without the attached drop leg. We do have a wide selection of similar style, 3,000 pound jacks that do not come with the drop leg. I recommend the Bulldog Square Jack # BD195369, which is a square, weld-on jack that has a 15 inch lift and does not include a drop leg or foot. I have included a video demonstration of this jack for your review. Another option is the etrailer...
view full answer... - Replacement Drop Leg Pin for Square Direct Weld Jack with Footplate TJD-5000SThe only replacement pin we offer for the Square Direct Weld Jack w/ Footplate part # TJD-5000S is the Replacement Snapper Pin for Ram Jack Footplates, Casters, and Couplers part # JFC-PN which is designed to secure the Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks part # TJD-5000-FT.
view full answer... - Will etrailer Square Marine Jack # MJSQ-2500B Fit 5-1/2 Inch Tall Trailer TongueFrom the center of the top hole on the mounting bracket for the Fulton Square Marine Jack # FHD2500 to the center of the bottom hole there is a distance of right at 5-3/8 inches. This jack will mount to 3 inch x 5 inch trailer frames so if you have a 5-1/2 inch tall frame this will not fit. We do not currently have a bolt-on jack available that will work on a 5-1/2 inch tongue. Your best option will be to go with a weld-on trailer jack like the Square etrailer.com # TJD-5000S. This square...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Updated by:
Lindsey S
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Hannah L
Updated by:
Mike S
Installed by:
Cole B
Written by:
Amanda M
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.