Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
(189 reviews)
Price: $71.39
In Stock
Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
Item # TJD-12000-RODNUT
Our Price: $71.39
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (189)
- Q & A (0)
- Videos (1)
- Photos
etrailer Accessories and Parts - TJD-12000-RODNUT
- Camper Jacks
- Trailer Jack
- Hardware
- Rod
- etrailer
Replaces the ACME threaded rod and threaded nut on your etrailer or Ram square, direct-weld jack with a 10,000-lb lift capacity and a 12,000-lb static capacity. Designed for TJD-12000 Series jacks.
Features:
- Replaces the threaded ACME rod and lift nut from your etrailer and Ram square, direct-weld jacks with a 10,000-lb lift capacity and a 12,000-lb static capacity
- Designed for TJD-12000 Series jacks
- Includes:
- 1 ACME rod
- 1 Lift nut
Specs:
- Lift capacity: 10,000 lbs
- Static capacity: 12,000 lbs
- Overall dimensions of rod: 17-3/4" long x 1" diameter
- Lift nut fits 3-1/2" x 3-1/2" square jack inner tube
TJD-12000-RODNUT Replacement ACME Screw Rod and Lift Nut for Ram 12,000-lb Jacks
Video of Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of etrailer Replacement Rod And Nut etrailer Ram Square Jack - TJD-12000-RODNUT
Hi everybody, Andy here with etrailer.com, and today we're gonna take a brief look at this replacement rod and nut. This is going to replace the threaded ACME rod and lift nut on your etrailer or Ram Square Jack, Direct Weld jacks with a 10,000 pound lift capacity and a 12,000 pound static capacity. This is designed for the TJD-12000 series jacks, so you just have to remove your old one and place this new one in with all of your bearings and other components installed. You will have to reuse your old components, or you can pick up new ones here etrailer.com if you need them. Let me lay this down here real quick and give you some overall dimensions. So looking at the overall length simply from end to end we are sitting right at 17 1/5 inches long, and the diameter is one inch, and the lift nut is 3 1/2 inches by 3 1/2 inches.
And so if you are needing to replace the rod and lift nut in your etrailer or Ram Square jack, specifically the TJD-12000 series, this is going to be exactly what you need. Well, that's gonna conclude our brief look today. I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me.
.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Defective
Customer Reviews
Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K - TJD-12000-RODNUT
Average Customer Rating: 4.6 out of 5 stars (189 Customer Reviews)
Replaces the ACME threaded rod and threaded nut on your etrailer or Ram square, direct-weld jack with a 10,000-lb lift capacity and a 12,000-lb static capacity. Designed for TJD-12000 Series jacks.by: Vince10/23/2022
The jack screw nut on my Big TEX 14k trailer got stripped when it was bottomed out.This unit is a great replacement and arrived from eTrailer a day early. The unit arrived with the grease dish located on the bottom side of the nut, but it was easy to relocate so it matched the original unit and the advertised foto. I would certainly order from etrailer again.
by: Rebecca02/16/2023
The product will not work for our jack as the top shaft is too short (shorter than our original shaft on the top). The rod itself is the right size overall but where you put your bearing and spacer is not long enough for the bearings and spacer we have from the original. We are trying to find a thinner bearing that might work otherwise we will have to buy a whole new jack. (unfortunately the placard that was on the original jack is rub off so we don't know the exact brand that we have but it came off an older model 4 horse gooseneck trailer so no telling what model it is0.
Rebecca
2/16/2024
We unfortunately werent able to use it as it wouldnt work for the jack we had,
Mike L.
2/16/2024
@Rebecca We're sorry to hear that! The replacement rod/nut is designed to replace the original in an etrailer or Ram brand square, direct-weld jack with a 10,000-lb lift capacity and a 12,000-lb static capacity. Designed for TJD-12000 Series jacks.
by: Daniel02/28/2020
My 2017 Big Tex 14k equipment trailer jack would not lift my trailer. I finally got tired of using a jack and took it apart after watching the rebuild video here on eTrailer.com. I then found my jack was stripped. I ordered this part, it fit perfect and fixed my trailer!
Daniel
3/2/2021
Still working like new! Thanks etrailer!
by: Wilbur 02/06/2023
It was easy to remove & replace watched the video just to make sure I did everything right. Received the part a little late, but that was due to weather. Overall Excellent service and understanding when ordering part!
Wilbur
2/7/2024
Working great!
by: Allen04/27/2024
Correct lift nut to repair my Big Tex 14ET trailer jack, the bearing dust cover did not fit so I used the old one. Packaging could have been better.
by: Amador04/08/2024
Great place to find parts you need for your trailer pricings right shipping fast even through USPS. I got it in three days. Thank you.
by: Randall04/07/2024
Product saved me a lot of money so that I could repair my jack instead of buying a new one. Ordering was easy and delivery was fast.
by: Keith10/12/2023
The leadscrew stripped out on my Delco 14k 20' trailer, and I really didn't want to cut the 10k jack off and weld on a new one. The label on the jack had white letters PRO with blue around them, and it looked a lot like the jack you sell:Checking through the product page and Q&A for this leadscrew the measurements looked right. It was an exact replacement and not too bad to replace. Hope this helps if someone else has a Delco trailer with a similar jack.
by: Dale 10/21/2023
Fast delivery. Actually haven't installed the new hitch because the replacement parts took care of the problem with our old one. Very happy with this company and would highly recommend for any trailer parts.
by: Joe 03/05/2024
This replacement rod & nut assembly worked perfectly! Easy to replace following the video posted on their website!
by: Kevin 10/25/2022
Item arrived in good time, exact match and installation went well.
Kevin
10/26/2023
It is holding up well and working smoothly!
by: Ted 03/08/2024
Easy replacement
by: David10/27/2022
Not what I ordered
Jenny N.
11/2/2022
Thank you for sending the picture and letting us know. Customer Service will be in touch with you.
by: Eduardo11/10/2022
It's compatible with my 2020 Big Tex trailer jack.
by: Eric 04/17/2024
Absolutely the best customer service.
The product was as advertised.
Quicker than expected delivery.
by: Brian02/13/2024
Ordered item two weeks ago, still waiting. If you’re in a hurry please find someone else. No refund, no parts till they hold you up for two weeks waiting. Then maybe they’ll look into it.
by: Dave H10/21/2023
My first time dealing with this company and it’s been amazing, easy to order off their website and they provided very prompt updates and order status
by: Edward 02/23/2024
Received unit earlier than expected. The part received did replace our old unit even though it was a smaller diameter by 1/4 of an inch which didn't make a difference at all! Hopefully will last a long time. Thank you Terri N
by: Peter 02/24/2024
Delivery estimate wasn’t even close the part worked great
by: Nate 02/10/2024
I received the part quickly and it fit perfectly.
by: Vladimir 02/12/2024
Fit right in and shipped really fast
by: RT02/16/2024
Fit perfectly on my Big Tex 14TL replacing my stripped screw drive. Easy to install and a lot cheaper than replacing the whole leg!
by: Steven 03/15/2024
Great help in finding the parts I needed
by: Jeffrey09/28/2023
Shipped quickly and great part. Finally have my jack working again!
by: John 03/07/2024
Great on time delivery!
25
189
Show More Reviews
See what our Experts say about this etrailer Accessories and Parts
- Solution for Lippert Stabilizer Jack that Has Broken ScrewWe've checked with Lippert in the past and the screw of their stabilizer jacks are not available so only option would be a new setup with the part # LC298707.
view full answer... - How to Determine Replacement Screw & Nut For Square Weld-On JackYou'd have to know the model number of your weld on jack to find the right replacement screw and nut. For example, the only replacement we carry is the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT which is for TJD-12000 Series jacks.
view full answer... - Replacement Nut for Ram Series 12000 JackThe Replacement Rod, Nut, and Grease Trap # TJD-12000-RODNUT is a fit for the 12000 series of Ram or etrailer jacks such as # TJD-12000SP-R2. It is specifically designed for square, direct-weld TJD-12000 Series jacks; the lift nut will fit 3-1/2" x 3-1/2" square jack inner tubes. If this matches the description of your jack it will work for you.
view full answer... - Replacement Threaded Rod For a 12,000LB Pacific Rim Jack On a Gator Mare TrailerPacific Rim is the manufacturer of the RAM jacks. You can verify the Replacement Rod and Nut # TJD-12000-RODNUT you found is the correct part by confirming your jack is 3-1/2" by 3-1/2" square and the 1" rod is 17-3/4" long. If you have a different measurement on either please let me know.
view full answer... - Does Replacement ACME Screw Rod # TJD-12000-RODNUT Work for RAM Brand Trailer JacksI would almost guarantee that the # TJD-12000-RODNUT is the correct part you need since you said you have a RAM brand trailer jack. This is designed to fit square RAM jacks like what you have so this would be what you'd want most likely. Feel free to email me a picture of what you have though and I'll take a look.
view full answer... - Replacement Trailer Jack For Rice Trailer That Currently Has Ram 14K JacksThe Ram 14K jacks don't have a replacement rod and nut available like the 12K # TJD-12000-RODNUT and are no longer available in that capacity. I recommend changing out your jacks for the 12K option. You can use the Bulldog Side Wind Jack Assembly - 12,500 lbs # BD182700 or the Buyers Products # 3370091410H or # 3370091415H as a replacement. These are all excellent products for the price to help your trailer function as intended.
view full answer... - How to Replace Interior Ram Jack Rod and Nut # TJD-12000-RODNUT on 12000 Series JacksGood news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears # TJD-12000-RODNUT in the # 12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically, you will not need to remove or cut the steel plate inside the top of the jack to do this. You will want to remove the cap, then the roll pin that holds the cross shaft into the leg, this will free up the smaller gear that will be removed...
view full answer...
- Bolt-On Side Mount Caster Wheel Tongue Jack to Replace Fulton 1000-lb Jack We do sell replacement jack parts including the main screw like the one shown in your photo. Examples of these replacement jack screws are # TJD-12000-RODNUT, # BD500250 and # BD500217 which are shown on the linked page. Unless you can positively identify the model of Fulton jack you have I strongly recommend replacing the whole jack instead of trying to rebuild the old one. You may even save money by getting a new jack; you'll also get a new warranty and have the confidence of knowing...
view full answer...
- Ram Square Jack Replacement Screw AssemblyWe have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut # TJD-12000-RODNUT will fit the following Ram jacks: # TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle # TJD-12000SP-R2NH 10K Sidewind with 12-1/4 inches of travel w/o handle # TJD-12000SP-R2 10K Sidewind with 12-1/4 inches of travel w/handle Some other replacement parts for these Series jacks are: # TJD-12000-GR Replacement Gear Kit # TJD-12000-BR Replacement...
view full answer...
- Recommended Trailer Jack Replacement for Stallion BrandThe Stallion Jack brand is not directly compatible with anything we carry. The closest thing we have is the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT which is 3-1/2 inches x 3-1/2 inches. I don't think that will work for you, so I recommend using the Square 2-Speed Jack w/ Crank - Drop Leg w/ Spring Return - Sidewind - 25-7/8" Lift - 10K # TJD2SP-12000SP-F as a replacement.
view full answer...
- Option For Wanting to Upgrade Ram Jack to Powered Landing GearThe Ram 12000 jack that you have can have the motor kit part # BD1824200100 that you mentioned added to it to convert it a powered jack.
view full answer... - Replacement Rod and Nut for a Bulldog 12,000 lb Trailer JackIf your rod is 1-1/4" diameter, then it sounds like you have a 12K Bulldog Trailer Jack for which the Replacement Screw and Nut Kit part # BD500217 at 17" long x 1-1/4" diameter most closely resembles the Replacement Rod and Nut Kit part # TJD-12000-RODNUT that you were looking at so it may be what you need. However, I would not be able to confirm unless I have the model number of the jack and date it was manufactured.
view full answer... - Replacement Screw for Trailer Jack with 1-1/4 Inch DiameterThe Ram Trailer Jacks generally use a 1" diameter threaded rod whereas the Bulldog Trailer Jacks generally use a 1-1/4" threaded rod. Therefore, it would appear as if you have a Bulldog Trailer Jack and in which case the Replacement Screw and Nut Kit part # BD500217 at 17" long x 1-1/4" diameter most closely resembles the Replacement Rod and Nut Kit part # TJD-12000-RODNUT that you were looking at so it may be what you need. However, I would not be able to confirm unless I have the model...
view full answer... - Replacement Bearing, Rod And Nut For The Ram 12000 Series Trailer JackIf you're needing a replacement bearing for your Ram 12000 Series jack, you can use the: -Replacement Bearing for etrailer and Ram Square Jacks # TJD-12000-BR. This will replace an individual bearing on your jack and has an inner diameter of .862", and an outer diameter of 1.955". Additionally, if you're also looking for a replacement rod and nut, you can use the: -Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT. If you're looking for a different...
view full answer... - Replacement RV AC Unit Recommendation for Dometic DUO ThermThe Advent AC unit part # ACDOM150 will work great as a replacement for a Dometic Duo Therm unit like you have. We had a customer come back and tell us how well this worked as a replacement for a Duo Therm and that no modifications were needed.
view full answer...
- Solution for Ram Square Direct Weld Jack that Has Broken Return SpringThe return springs in landing gear jacks are not replaceable or repairable unfortunately so if you have the # TJD-12000SP-R2NH.
view full answer... - Thread Pitch of Replacement Rod and Nut for TJD-12000 Direct Weld Jacks We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement part # TJD-12000-BR.
view full answer...
- Replacement Parts For Ram 12K Support Capacity Jack # TJD-12000SP-F2Here is a list of the replacement parts we have for the Ram 12K Support Capacity Jack # TJD-12000SP-F2 you found. Replacement Sidewind Crank # TJD-12000-HD Replacement Plunger Pin Assembly # TJD-12000-PPN Replacement Cap # TJD-12000-CP Replacement Return Spring # TJD-12000-RSP Replacement Handle Clip # TJD-12000-CLIP Replacement Handle Shaft # TJD-12000-SHABUS Replacement Rod and Nut # TJD-12000-RODNUT Replacement Bearing # TJD-12000-BR Replacement Sidewind Gear Kit # TJD-12000-GR
view full answer... - Replacement Trailer Jack Parts for WW Brand Cattle TrailerThe threaded rod you are looking to replace is not a universal fit for all jacks. I recommend taking a look at the components in your jack to determine the correct replacement. There are a few options we carry but the Bulldog winches have a very specific shape to the nut. I've got the following options to offer: -Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT -Replacement Screw and Nut Kit for 12000-lb Capacity Bulldog Jacks # BD500217 -Replacement...
view full answer... - Recommended HD 12000lb Sidewind Square Jack With At Least 24" LiftI have a different option, but the closest option we have in a sidewind jack with a 12000lb capacity is the Buyers Products Heavy-Duty 4" Square Jack w/ Side Pin Drop Leg # 3370091410H which has 26" of lift. This is a little more than you were looking for but will still work. I included a video of the # 3370091410H for you to take a look at.
view full answer... - Gear Kits for Single Speed Ram or etrailer JackIt is not possible for me to tell you with any degree of certainty that you can retrofit the Replacement Gearbox for etrailer and Ram 2-Speed Square Jacks # TJD2SP-12900-GBX for use with a single speed Ram jack though there are replacement gears available. If you have the TJD-12000 Series jacks such as # TJD-12000SP-R2 there is the Replacement Sidewind Gear Kit # TJD-12000-GR as well as Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT which you...
view full answer... - Recommendations For Repairing Or Replacing An Older Stallion JackI may have a different solution for you, but there will not be a universal kit to add a motor to your Stallion jack, unfortunately. With that being said, I have 2 options below for you to check out. Both will be weld on applications, but are definitely worth looking at. First is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. This will have 38 inches of lift and is rated to a combined weight of 12,000 pounds. One of the big pluses with this unit is that the jacks are independent...
view full answer... - Do Nut & Bearing Come Separate For Ram/etrailer 12k Support/10k Lift Square JackThe replacement nut and bearing for the Ram/etrailer 12k support/10k lift square jacks are not available separately as they are only packaged together with the shaft: - Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT As for the roll pins, they are also available, but are come in the package with replacement gears: - Replacement Sidewind Gear Kit # TJD-12000-GR While I know this isn't what you were looking to hear, you will have some extra parts...
view full answer... - Replacement Top Cap for RAM Square Tube JackIt sounds like you are seeking the cap for the top of your square jack. The Replacement Cap for etrailer and Ram Square, Direct Weld, Sidewind Jack # TJD-12000-CP will fit the 4 x 4 inch outside square jacks.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Jameson C
Expert Research:
Adam R
Installed by:
Kathleen M
Installed by:
Andy C
Updated by:
Wilson B
Updated by:
Jenny M
Updated by:
Kristina F
Updated by:
Mike S
Updated by:
Noah M
Written by:
Amanda M
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Vince
10/24/2023
working fine