Replacement Parts For Ram 12K Support Capacity Jack # TJD-12000SP-F2

Question

Question:

Do you have a rebuild kit for a 12k Ram Trailer jack?

asked by: Kevin G

0

Expert Reply:

Here is a list of the replacement parts we have for the Ram 12K Support Capacity Jack # TJD-12000SP-F2 you found.

Replacement Sidewind Crank # TJD-12000-HD
Replacement Plunger Pin Assembly # TJD-12000-PPN
Replacement Cap # TJD-12000-CP
Replacement Return Spring # TJD-12000-RSP
Replacement Handle Clip # TJD-12000-CLIP
Replacement Handle Shaft # TJD-12000-SHABUS
Replacement Rod and Nut # TJD-12000-RODNUT
Replacement Bearing # TJD-12000-BR
Replacement Sidewind Gear Kit # TJD-12000-GR

expert reply by: Bud M

0

Answer 1

I went ahead and linked the video you are referencing about rebuilding a square jack like the Square Direct Weld Jack #TJD-12000SP-F2 from our website to this answer. We have a number of replacement parts in that video and some that were not included…

view full answer...

Answer 2

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 3

We have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut #TJD-12000-RODNUT will fit the following Ram jacks: #TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle #TJD-12000SP-R2NH 10K…

view full answer...

Answer 4

I have a solution for you, but the Replacement Plunger Pin Assembly for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs #TJD-12000-PPN is 3/4" diameter. Instead, you can use the Replacement 1/2" Plunger Pin Kit for Fulton Marine…

view full answer...

Answer 5

I have attached the diagram with all of the dimensions of the Pro Series Square Jack - Drop Leg w/ Spring Return #PS1400950376 you are looking for. The Pro Series #PS1400950376 has a 10000lb weight capacity, is a direct weld on design, and includes a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Parts For Ram 12K Support Capacity Jack # TJD-12000SP-F2

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching