Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
(104 reviews)
Price: $44.95
In Stock
Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
Item # LC146059
Retail:$57.95
Our Price: $44.95
You Save: 22%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (104)
- Q & A (0)
- Videos (1)
- Photos
Lippert Accessories and Parts - LC146059
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Lippert
- Lead leg repair kit for Venture powered landing gear assemblies
- Kit includes:
- 1 Lead drive shaft
- 2 Drive shaft bushings
- 1 E-Clip
- 1 Drive pin
- 1 Spiral pin
- (1) 12T bevel gear
- (1) 16T bevel gear
- 1 Shim washer
- Made in the USA
146059 Lippert Components Venture Lead Leg Repair Kit
Video of Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of Lippert Components - Trailer Jack,Camper Jack - LC146059
Today we're going to take a quick look at the Lippert Components Venture Lead Leg repair kit for 5th-wheel RV landing gear.Now if you've had your landing gear for a long time or it's just not really working the way it should and the gears aren't really lining up they used to. It's getting harder and harder to deploy that landing gear out and retract it back in, an easy way to extend the life of that landing gear is to replace the components inside it.It's going to be a pretty easy job. It might be a little bit messy since there is some grease in there to keep everything lubricated and working as it should. But really, all you'll need is some extra grease and, maybe a pair of pliers and a screwdriver.Pop the top off of your landing gear. Remove the components. Be sure to clean those off.
Look for any spots of damage and try to make sure that you remember which part goes where. And then replace all your components in the same order that you took the old ones out.Included in our kit, we're going to get one drive shaft, which is going to be this longer piece here. We'll also get our two bevel gears. We're going to have our, sort of, smaller but fatter one. This is going to be our 12-T bevel gear, and then our 16-T bevel gear.We'll get our two drive shaft bushings, a shim washer, an E-clip, this spiral pin.
You can see it's a little rolled up spiral there. And also our drive pin.So again, all these components are going to fit in a specific order. Your drive pin is going to fit inside our larger washer like that.And then the spiral pin is going to fit inside our smaller bevel.And again, you just want to make sure to note the order the order that you take things out and just replace them the same way.This is going to be a lot easier and quicker, more affordable way to replace your damaged components and get your landing gear back to working as it should, rather than having to replace your entire assembly.Again if you do need any grease to pack in there to make sure everything is lubricated, you can also find that here at etrailer.com, so definitely check that out if you need to pick any up.This product is also made in the USA, and that's going to do it for our look at the Lippert Components Venture Lead Leg repair kit for 5th-wheel RV landing gear.
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Alternate product found
Customer Reviews
Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear - LC146059
Average Customer Rating: 4.8 out of 5 stars (104 Customer Reviews)
by: Brad03/07/2023
Installed on our 2012 Dutchmen Voltage exact replacement. Awesome fit. Used for rear and stabilizer landing legs. Completely disassembled, cleaned thoroughly entire thread. Existing gears showed normal wear but replaced any way. With new bushing provided back to like new.
The front lead and follow legs were replaced but plan to rebuild old with new gears and bushings will keep just in case of one of those days happens. Highly recommend doing this before a failure on the road.
by: Mike 02/03/2024
Kelly was very helpful with getting me the rebuilding kits for my jack she was very professional with helping me everything fit perfect ty
by: Eric02/04/2024
I had to modify the shaft where it shoulders up to the gear box. The gear box has a squared off shoulder, as to the shaft from this kit has a tapered shoulder. I was able to correct this with a bastard file.
by: Dave (11/11/2023
Great customer service. My 1999 trailer is located in Mexico, it was difficult trying to figure out the correct parts and they were able to figure it out with a few photos. The parts were exactly what I needed and have been working as expected since. Thanks etrailer!
by: Randall 11/22/2023
Received all components as listed on order page, all in good condition. Installation was easy, tolerances are nice and tight but still fit well together. So far, so good.
by: Leann02/09/2024
This was exactly what we needed. Shipped fast. The only thing that would have been easier was if you came and installed it. Lol
by: FireMedic-C35107/26/2023
Rebuild kit was an exact fit and works perfectly, unfortunately the drive screw is binding up so I’ll be replacing the whole leg.
by: Joseph08/12/2022
etrailer is a great company the 2 ladies that helped me were fabulous VERY KNOWAGEABLE AND Friendly MELISSA and JOANNE.
by: Wes03/06/2022
Works perfect on my nitrous toy hauler. Installation was quick and simple.
Wes
3/7/2023
Works great, have had no issues. Trailer goes up and down like it should.
by: Mike 06/10/2023
Would recommend this product rather than buying new landing jack. Very easy repair
by: Michael10/18/2023
Worked good when I sold the camper.
by: Randy 09/15/2023
Excellent parts and shipping couldn't ask for any thing more.
by: Skylar03/16/2023
Have yet to install, hence the less excellent rating. However, the parts do feel quite solid. I ordered both the lead leg kit and follow leg kit just to get them both done and over with (its a 2004 model year)
by: Mark04/12/2019
Works great. Used to to separate the 2 landing legs on my 5th wheel trailer to allow for independent operation with 2 motors. This modification is done on the passenger side leg (the one without the motor). By adding these parts, you can now install the new motor (LG-142178) and gear box (LC276602) to operate each landing leg separately. -obviously you will need to install a second switch and the appropriate wiring. Great modification -should have been installed like this from the factory.
Mark
4/13/2020
Still working great. No issues
by: Harry 04/01/2023
Everything was a easy install the only thing that didn’t fit was the bushings. I will order more parts from e trailer if i ever need anything else. The person that took my order was a big help .
by: Rex11/17/2017
After shearing off the main pin of the landing gear on my Raptor 5th wheel toyhauler, I ordered the the Lippert landing gear repair kit from etrailer. They were extremely helpful, verified fitment, and shipped it immediately. It not only was easy to replace, but fit /worked perfectly.
Rex
11/17/2018
After a year of use, my landing gear is working great. Im so glad I purchaseinstalled the repair kit myself, as it was easy, and I saved hundreds in shop labor costs.
by: Mike08/04/2023
Missing pieces. Not impressed at all.
by: James 06/25/2023
Perfect fit, easy to rebuild , and cheaper than a new leg.
by: Mike 08/07/2022
$50 dollars for a rebuild kit vrs $325 dollars for a complete jack leg, you do the math :) My trailer repair man stated his company couldn't get the rebuild kit and the entire jack leg would cost me $500 dollars retail price !!!! Not only did E-trailer have the jack leg and the rebuild kit, they were way lower priced than dealing with my on sight service tech. So, I bought the rebuild kit and did it myself and it works like it should !!!!!!
by: Grant 12/26/2022
Just the replacement kit I needed to replace the sheared shaft when I retracted the leg too far.
My wife warned me.
Delivery was fast.
by: L.Gray05/21/2019
Lippert landing gear rebuild kit is still working flawlessly. God bless.
Lee G.
5/22/2020
Gears are still working great. God bless.
by: Johnny 08/09/2022
Great service. Real helpful on placing order. Stacy was really polite & getting my order to me on time. Had my lead leg repair kit for landing gear repaired & back on road as promised.
by: Ronald 08/09/2020
received Lippert repair kit for our 5th wheel. it was exactly what we needed. quality parts. installed new gears as well even though I only needed drive shaft. Would highly recommend it.
by: Jim B.10/24/2017
My first review that I compelled to write because the service and product were excellent. After viewing a YouTube video to determine why my Fifth Wheel landing gear would not extend or retract, I knew this repair kit was exactly what I needed. Ordered kit at 4 pm Thursday and received package in the mail Saturday. All parts were an exact match. Lesson learned - lube the bevel gears in top of the landing gear legs. Cap on top is easy to remove. Hats off to Chelsey who helped me place the order and provided exceptional follow-up.
by: Steve03/08/2019
I bought an older 5th wheel camper that needed some work. I was happy to find etrailer that had replacement parts. Delivery was fast and the parts are exact replacements for what I need. I appreciate the follow-up email as well. My leveling jacks are back doing their job. I'm probably going to order the tailgate I found for my truck next!
25
104
Show More Reviews
See what our Experts say about this Lippert Accessories and Parts
- Replacement Motor for Venture Fifth Wheel Landing GearThe replacement motor for Venture fifth wheel landing gear is Lippert Components Venture 5th Wheel RV Landing Gear Motor # LC142178. The switch you'd want is Lippert Components 5th Wheel RV Landing Gear Switch # LC145236; the gearbox is Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies # LC276602. If you needed repair kits, we have those as well, the Lippert Components Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059 and the Follow...
view full answer... - What Causes Landing Gear to Blow Fuse with Replaced Motor and GearboxIf the motor and gearbox both checkout then the next likely cause of the problem would be the internal gears which can be replaced with the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear part # LC146059 or Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear part # LC146060. If you're looking for a higher rated landing gear motor, I recommend the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor part # LC196308. If you want to switch to a dual landing...
view full answer... - Repair Kit for Lippert Landing Gear Set LC333964For the Lippert landing gear set part # LC333964 the correct repair kit would be the part # LC146059.
view full answer... - Difference Between Lippert Lead Leg Repair Kit # LC146059 and Stromberg Carlson # LG-146059The Lippert Components Lead Leg Repair Kit # LC146059 and the Stromberg Carlson Kit # LG-146059 referenced in your question are essentially the same kit. I went out to our warehouse to verify this. It is actually not too uncommon for landing gear components like these to be interchangeable between different manufacturers, especially between Lippert and Stromberg Carlson. If you have a Lippert Landing Gear System on your 2007 Fleetwood Gearbox Fifth Wheel Trailer, then either of these kits...
view full answer... - Parts Needed To Repair Broken Landing Gear Legs On Keystone Raptor TrailerWe do offer repair kits for most landing gear legs, the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear part # LC146059 or Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear part # LC146060. That said, they only included select components and if the part you're looking for is not included you'd be best off replacing the entire legs. The Stromberg Carlson Manual Landing Gear Set part # LG-183708 will replace legs that have a 29-1/2" long outer tube and...
view full answer... - Troubleshooting Venture M-9000-PK Landing Gear on 2010 Komfort Fifth Wheel TrailerThe next step is to take apart the top of the jack and check the gears there. If you find your problem there, possibly some worn gear teeth, and you have Lippert landing gear, the repair kits are parts # LC146059 for the lead leg and # LC146060 for the follow. Another possibility is the screw down the center of the jacks has possibly gotten stripped. However, if this is the case your best bet will be to replace the legs. You'll need to measure the outer tube to determine which legs...
view full answer... - Replacement Landing Gear Repair Kit for VMC900R JacksThe difference in the repair kits for your VMC900R will be the Drive Shaft; a lead leg kit will have a different shaped shaft than the follow leg. The replacement Landing Gear Kit for Venture Follow Legs is # LC146060, while the Lead Leg repair kit is # LC146059. I have linked all of the above mentioned products to this page for your convenience.
view full answer... - Repair Kit Recommendation for a Venture VMC900 Lead LegYes, for your Venture VMC900R lead leg jack the part # LC146059 is the correct repair kit.
view full answer... - Replacement Repair Kits For Venture Landing Gear Legs VMC900The replacement repair kit you will need for your Venture Landing Gear Legs VMC900 is The Lippert Venture Follow Leg Repair Kit # LC146060, for the follow leg, and The Lippert Venture Lead Leg Repair Kit # LC146059 for the lead leg. I attached a review video link below.
view full answer... - How To Fix Stripped Gear Inside Lead Landing Gear Leg on a 2010 Colorado 5th WheelThe most cost effective option we have for you to fix the issue you have with the stripped gear inside of your lead landing gear leg would be to obtain the Lippert Components Venture Lead Leg Repair Kit part # LC146059. If you want to replace the entire leg as well this can be done (although not necessary) but in order to offer a replacement I would need to know the outer tube length and your weld stop spacing.
view full answer... - Determining Which Rebuild Kit Is Correct For Landing Gear On 2010 Forest River Wildcat 5th WheelIt may very well be possible to rebuild the landing gear on your 2010 Forest River Wildcat 5th wheel with a rebuild kit, but first you will need to identify which model landing gear is installed. On either of the landing gear legs there should be a part number, this may be on a white sticker or stamped into the metal depending on the specific landing gear. With this part number I can then identify your landing gear and recommend the correct rebuild kit. If there is not any part numbers...
view full answer... - Replacement Parts for Venture Landing Gear That SlipsThank you for the photo of your trailer landing gear interior. We can help you with a repair kit for the lead and follower legs of your Venture landing gear. For a lead leg repair kit use # LC146059 and for the follow leg use kit # LC146060. It is hard to tell for sure from the photo but it does appear that your existing gear set shows metal filings (a natural outcome of use) that would explain the slipping. White lithium grease # L11354 is ideal for lubricating the new gear kits.
view full answer...
- Landing Gear Lead Leg Repair Kit for Lippert Landing Gear on 2011 Palomino PumaThe gear repair kit for the lead leg of Lippert LCI Power Landing Gear on your 2011 Palomino Puma is the Lippert Components Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059. This repair kit is designed for the lead leg of electric Lippert landing gear. The kit includes 1 lead drive shaft, 2 drive shaft bushings, 1 E-clip, 1 drive pin, 1 spiral pin, 1 12T bevel gear, 1 16T bevel gear, and 1 shim washer.
view full answer... - Venture Landing Gear Rebuild Kits We have Venture landing gear repair kits with part # LC146060 for the follow leg or part # LC146059 for the lead leg. To install the kits you'd want to take the legs off of the trailer.
view full answer... - Correct Repair Kit for Venture Landing Gear Legs VMC900The correct repair kits we have for the Venture Landing Gear Legs VMC900 is part # LC146060 for the follow leg and part # LC146059 for the lead leg.
view full answer... - Does Lippert Venture Lead Leg Repair Kit FIt Stromberg-Carlson Legs on Landing GearIt does, yes; if you have Stromberg-Carlson landing gear you can use the Lippert Venture repair kit, which is the following part number: - Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059
view full answer... - Lead Leg Landing Gear Repair Kit for a 2011 Forest River Flagstaff Classic Super Lite Fifth WheelIt looks like your 2011 Forest River Flagstaff Classic Super Lite does in fact use Lippert Components landing gear. The Venture Lead Leg Repair Kit, part # LC146059, will in fact work with this. This is designed by Lippert Components for repairing these legs. I've linked to a video review of this repair kit for you to look at. Remember that this is the repair kit for the lead leg. If you need the follow leg instead or in addition, then use part # LC146060.
view full answer... - Repair Kit For Venture 5TH Wheel Landing Gear On a 2011 Keystone OutbackIt appears your 2011 Keystone Outback Sydney Edition 330FRL will have Venture landing gear. If this is true the Repair Kit # LC146059 is for the lead leg on the drivers side and the Kit # LC146060 is for the follow leg on the passenger side. I wasn't sure when you said left leg if that was in reference to the trailer or looking at the jacks from the front of the trailer.
view full answer... - How to Find the Correct Replacement Lead Leg for 5th Wheel Landing Gear Thanks for all the information! You are correct that is the lead leg because it is closest to the gear and the motor. However, in order to determine which replacement lead leg you need, you'll need to find the model of the landing gear on your trailer and measure it's outer tube length. This is something we have no way of knowing and I wouldn't want to assume anything. For example, if you do have a Venture landing gear with legs that measure 29-1/2" you can replace the leg with the Replacement...
view full answer... - Replacement Landing Gear Legs or Repair Parts for Landing Gear VM900L-068652We have repair kits for the VM900L series. The repair kit for the follower leg is # LG-146060 and the repair kit for the lead leg is # LC146059. Replacing the parts is going to be a whole lot less expensive that replacing the legs. If you want to replace the legs anyway then we have # LG-179014 as the follower and # LG-179013 as the lead leg.
view full answer... - Lead And Follow Leg Repair Kit For A Lippert Venture Landing Gear VMC900R-327953For your lead jack leg on your Lippert Venture Landing Gear VMC900R-327953, you will want to use the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059. As for a follow leg kit, you will want to use the Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear # LC146060. Attached are a couple of review videos for you to check out.
view full answer... - Recommended Venture Landing Gear Rebuild Kits For the Venture landing gear, I recommend the Lippert Components Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059 and the Lippert Components Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear # LC146060.
view full answer... - Troubleshooting Landing Gear Making Popping Sounds and Operating IntermittentlyI reached out to my contact at Lippert regarding the issue you're having with the landing gear on your trailer and something jumped out at him right away as being the most likely culprit. He noticed that the voltage you checked at the battery was 13.24V but at the motor leads it dropped to 11.94V. This is an indication that the battery was being charged or still had some surface charge but the battery itself wasn't/isn't fully topped off and thus not entirely capable of powering the system...
view full answer... - Recommended Lead and Follow Leg Landing Gear Repair Kit for a Jayco 5th Wheel You most likely have a Lippert Venture landing gear on your Jayco 5th wheel since that's typically what comes standard on most 5th wheels. With that said, you can use the Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear # LC146060 for the follow leg, and # LC146059 for the lead leg.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Installed by:
Kathleen M
Written by:
Chelsea B
Updated by:
Wilson B
Updated by:
Mike S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Brad
3/8/2024
The rebuilds are working as well as the ones I replaced at same time with new. Planned preventive maintenance beats a failure on the road. Keep them greased and replace if show significant wear.