Replacement Top Cap for RAM Square Tube Jack

Question

Question:

RAM model 12000 square tube cap Looking for the cap that goes on the RAM Model 12000 trailer jack.

asked by: Adam H

0

Expert Reply:

It sounds like you are seeking the cap for the top of your square jack. The Replacement Cap for etrailer and Ram Square, Direct Weld, Sidewind Jack # TJD-12000-CP will fit the 4 x 4 inch outside square jacks.

expert reply by: Jason S

0

Answer 1

We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement…

view full answer...

Answer 2

To repair a Ram Series 12000 jack, like #TJD-12000SP-R2, we have the Gear Kit #TJD-12000-GR or the Replacement Rod and Nut #TJD-12000-RODNUT. Or you could need both. I just depends on what the problem is exactly.

view full answer...

Answer 3

The Ram Trailer Jacks generally use a 1" diameter threaded rod whereas the Bulldog Trailer Jacks generally use a 1-1/4" threaded rod. Therefore, it would appear as if you have a Bulldog Trailer Jack and in which case the Replacement Screw…

view full answer...

Answer 4

The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part #TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer…

view full answer...

Answer 5

The Replacement Rod, Nut, and Grease Trap #TJD-12000-RODNUT is a fit for the 12000 series of Ram or etrailer jacks such as #TJD-12000SP-R2. It is specifically designed for square, direct-weld TJD-12000 Series jacks; the lift nut will fit 3-1/2"…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

It sounds like you have an error on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817. There are a lot of different errors that may possibly pop up with the Lippert Ground Control. Can you tell me exactly what the…

view full answer...

Answer 12

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Replacement Top Cap for RAM Square Tube Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching